Arriba

Inicio » Catalogo » Electrónica, Audio y Video » Componentes Electrónicos > Semiconductores > Circuitos Integrados

Componentes Electrónicos > Semiconductores > Circuitos Integrados

Mostrar: 
Mostrar del 1 al 24 (de 177 productos)
Páginas de Resultados:  1  2  3  4  5 ...  [Siguiente >>] 
  • Adafruit Sewable CR2032 Battery Holder
    Precio:  $46,309.00
    Agregar al Carrito   Vista

    Adafruit Sewable CR2032 Battery Holder

    -Titulo Original : Adafruit Sewable CR2032 Battery Holder-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 653 // Stock Type: Power >> Battery Holders >> Coin Cell // In Stock & Ready to Ship // This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in the metal connection tabs, just large enough for a #5 or smaller needle to pass through. One tab connects to common ground (negative) and the other tab is +3 Volts. This holder is meant to be used with Lithium CR2032 (20mm diameter, 3.2mm thick) sized coin batteries. These are almost always 3V at about 200+ mAh capacity. Lithium coin cells are not rechargeable but they are very easy to find, available at any grocery store. Inserting the coin is easy, the holder is very sturdy, and it snaps out with a push. Its got a nice flat plastic back that you can easily glue in place for extra mechanical stability...
  • Bateria Adafruit Lithium Ion Polymer 3.7v 100mah
    Precio:  $60,249.00
    Agregar al Carrito   Vista

    Bateria Adafruit Lithium Ion Polymer 3.7v 100mah

    -Titulo Original : Battery Packs Lithium Ion Polymer Battery 3.7V 100mAh (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of ~100mAh for a total of about 0.4 Wh. If you need a larger battery, we have a full range of bigger cells The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry. Because they have a genuine JST connector, not a knock-off, the cable wont snag or get stuck in a matching JST jack, they click in and out smoothly. The included protection circuitry keeps the battery voltage from going too high (over-charging) or low (over-use) which means that the battery will cut-out when completely dead at 3.0V. It will also protect against output shorts. However, even with this protection it is very important that you only use a LiIon/LiPoly constant-voltage/constant-current charger to recharge them and at a rate of 100mA or less. We suggest our Micro Lipo charger, which has a 100mA default rate. Like most lipos, the batteries we sell do not have thermistors built in. This is why we suggest charging at 1 C or even less - 100mA is a good rate, and available from any USB port if using a USB-powered charger Additional safety notes: Do not use a NiMH/NiCad/lead-acid charger! Also, do not abuse these batteries, do not short, bend, crush or puncture. Never charge or use unattended. Always inspect batteries and surrounding circuitry constantly for any damage, loose wiring, or possibility of short circuits. As with all Lithium ion polymer batteries and with any power source - they should be used by experts who are comfortable working with power supplie...
  • Adafruit TCA9548A I2C Multiplexer [ADA2717]
    Precio:  $56,269.00
    Agregar al Carrito   Vista

    Adafruit TCA9548A I2C Multiplexer [ADA2717]

    -Titulo Original : Adafruit TCA9548A I2C Multiplexer [ADA2717]-Fabricante : ADAFRUIT-Descripcion Original: Finally, a way to get up to 8 same-address I2C devices hooked up to one microcontroller - this multiplexer acts as a gatekeeper, shuttling the commands to the selected set of I2C pins with your command. // Using it is fairly straight-forward: the multiplexer itself is on I2C address 0x70 (but can be adjusted from 0x70 to 0x77) and you simply write a single byte with the desired multiplexed output number to that port, and bam - any future I2C packets will get sent to that port. In theory, you could have 8 of these multiplexers on each of 0x70-0x77 addresses in order to control 64 of the same-I2C-addressed-part. // Like all Adafruit breakouts, we put this nice chip on a breakout for you so you can use it on a breadboard with capacitors, and pullups and pulldowns to make usage a snap. Some header is required and once soldered in you can plug it into a solderless-breadboard. The chip itself is 3V and 5V compliant so you can use it with any logic level. // You just found the perfect I2C sensor, and you want to wire up two or three or more of them to your Arduino when you realize Uh oh, this chip has a fixed I2C address, and from what I know about I2C, you cannot have two devices with the same address on the same SDA/SCL pins! Are you out of luck? You would be, if you didn't have this ultra-cool TCA9548A 1-to-8 I2C multiplexer! Finally, a way to get up to 8 same-address I2C devices hooked up to one microcontroller - this multiplexer acts as a gatekeeper, shuttling the commands to the selected set of I2C pins with your command. Using it is fairly straight-forward: the multiplexer itself is on I2C address 0x70 (but can be adjusted from 0x70 to 0x77) and you simply write a single byte with the desired multiplexed output number to that port, and bam - any future I2C packets will get sent to that port. In theory, you could have 8 of these multiplexers on each of 0x70-0x77 addresses in order to control 64 of the same-I2C-addressed-part. Like all Adafruit breakouts, we put this nice chip on a breakout for you so you can use it on a breadboard with capacitors, and pullups and pulldowns to make usage a snap. Some header is required and once soldered in you can plug it into a solderless-breadboard. The chip itself is 3V and 5V compliant so you can use it with any logic level...
  • Adafruit 1946 FONA - Mini Cellular GSM Breakout UFL Version
    Precio:  $194,159.00
    Agregar al Carrito   Vista

    Adafruit 1946 FONA - Mini Cellular GSM Breakout UFL Version

    -Titulo Original : Adafruit (PID 1946 FONA - Mini Cellular GSM Breakout UFL Version-Fabricante : Adafruit-Descripcion Original: Send and receive SMS messages // Send and receive GRPS data (TCP/IP, HTTP, etc) // Scan and receive FM radio broadcasts // NOT INCLUDED: Microcontroller, external antenna, SIM card, other components to complete your project // Soldering is required // Introducing Adafruit FONA MiniGSM, an adorable all-in-one cellular phone module that lets you add voice, text, SMS and data to your project in an adorable little package. This module measures only 1.75x1.25. At the heart is a GSM cellular module (we use the latest SIM800). This module can do just about everything. This version has a uFL connector. Quad-band 850/900/1800/1900MHz - connect onto any global GSM network with any 2G SIM (in the USA, T-Mobile is suggested) Make and receive voice calls using a headset OR an external 8Ω speaker + electret microphone Send and receive SMS messages Send and receive GPRS data (TCP/IP, HTTP, etc.) Scan and receive FM radio broadcasts (yeah, we don't exactly know why this was included but it works really well) PWM/Buzzer vibrational motor control AT command interface with auto baud detection Sounds delicious, right? So we plated this fine module onto a little breakout with all the extras you need to make your next project shine: Onboard LiPoly battery charging circuitry so you can take your project on the go. Use any 500mAh+ LiPoly or LiIon battery and recharge over the MicroUSB when necessary. Two LEDs let you know when its charging and done Standard 4-pole TRRS headphone jack. Use any 'Android' or 'iPhone'-compatible headset with mic Breakouts for external 8Ω speaker and electret mic if you don't want to use a headphone Level shifting circuitry so you can run it with 2.8V to 5V logic. Vibrational motor (buzzer) driver so you can have noiseless notifications uFL connections for external antenna Indicator LEDs for power and network connectivity Standard SIM slides into the back On its own, this module can't do anything. It requires a microcontroller to drive it! We suggest and use an Arduino but any 3-5V microcontroller with a UART can send and receive commands over the RX/TX pins...
  • Adafruit 8-channel Bi-directional Logic Level Converter [ad
    Precio:  $51,669.00
    Agregar al Carrito   Vista

    Adafruit 8-channel Bi-directional Logic Level Converter [ad

    -Titulo Original : Adafruit 8-Channel Bi-Directional Logic Level Converter [ADA395]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 395 // Stock Type: Breakout Boards >> Level Shifters & Expanders // In Stock & Ready to Ship // Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V. Although one can use resistors to make a divider, for high speed transfers, the resistors can add a lot of slew and cause havoc that is tough to debug. For that reason, we like using 4050/74LVX245 series and similar logic to perform proper level shifting. Only problem is that they are only good in one direction which can be a problem for some specialty bi-diectional interfaces and also makes wiring a little hairy. That's where this lovely chip, the TXB0108 bi-directional level converter comes in! This chip perform bidirectional level shifting from pretty much any voltage to any voltage and will auto-detect the direction . Only thing that doesn't work well with this chip is i2c (because it uses strong pullups which confuse auto-direction sensor). If you need to use pullups, you can but they should be at least 50K ohm - the ones internal to AVRs/Arduino are about 100K ohm so those are OK! Its a little more luxurious than a 74LVX245 but if you just don't want to worry about directional pins this is a life saver! Since this chip is a special bi-directional level shifter it does not have strong output pins that can drive LEDs or long cables, it's meant to sit on a breadboard between two logic chips! If you do not need instant bi-directional support, we suggest the 74LVX245 as below which has strong output drive. This breakout saves you from having to solder the very fine pitch packages that this chip comes with. We also add 0.1uF caps onto both sides and a 10K pull-up resistor on the output enable pin so you can use it right out of the box...
  • Batería de polímero de litio Kbt 3.8v 2000mah 754444
    Precio:  $86,579.00
    Agregar al Carrito   Vista

    Batería de polímero de litio Kbt 3.8v 2000mah 754444

    -Titulo Original : KBT 3.8V 2000mAh Li-Polymer Battery: 754444 Lipo Rechargeable Lithium-ion Replacement Batteries With JST Connector-Fabricante : KBT KEEP BETTER TECH-Descripcion Original: - Batería de polímero de litio 754444: 3,8 V 2000 mAh, las baterías vienen con conector JST, muy cómodo de usar. Uso amplio: la batería se ajusta a cámaras digitales, tabletas, monitores domésticos, GPS, juguetes, Network Box, ventilador USB, probador, purificador de aire, controlador, altavoz bluetooth, monitor para bebés, teclado y mouse, etc. - Larga vida útil: con alrededor de 800 ciclos de carga y descarga, la batería puede funcionar durante 1-2 años en uso normal. Si no usa la batería con frecuencia, agote la capacidad de la batería y cárguela por completo una vez al mes. ...
  • Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]
    Precio:  $100,649.00
    Agregar al Carrito   Vista

    Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]

    -Titulo Original : Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 390 // Stock Type: Power >> Solar >> Chargers // In Stock & Ready to Ship // NOTE: This product is only designed for use with solar panels sold at the Adafruit store. We cannot guarantee this will work with solar panels purchased elsewhere. Please purchase this kit and panels from Adafruit to ensure optimized functionality! A 2.1mm adapter cable is also required to adapt a solar panel to the DC power jack. Make your projects to go green this summer with our specialized USB/Solar Lithium Ion Polymer Battery charger! This charger is a very unique design, perfect for outdoor projects, or DIY iPod chargers. We've spent over a year testing and tinkering with this charger to come up with a plug and play solution to charging batteries with the sun and we're really pleased with what we ended up with. Easy to use! Pick up any of our many 3.7V/4.2V LiIon batteries , and a 6V solar panel . Plug the battery into the BATT port using a 2-pin JST cable and the solar panel into the DC jack using a 2.1mm adapter cable Put the solar panel outside (and keep the battery out of the sun, it needs to be kept cool!) to start charging. You can power another project like a Mintyboost at the same time by connecting to the LOAD output port Our carefully designed charger is designed specifically for solar charging, and will automatically draw the most current possible from the panel in any light condition! Even thought it isn't a 'true' MPPT (max power point tracker), it has near-identical performance without the additional cost of a buck-converter. Our detailed tutorial on how to use this charger includes a design document explaining how it all works. For use with Adafruit Lipoly/LiIon batteries only! Other batteries may have different voltage, chemistry, polarity or pinout. Comes with an assembled charger board, a 2-pin JST cable that will fit into either the BATT or LOAD ports, and a large stabilization capacitor that must be installed in your finished project. Doe...
  • Adafruit 2999 ATWINC1500 WiFi Breakout
    Precio:  $108,369.00
    Agregar al Carrito   Vista

    Adafruit 2999 ATWINC1500 WiFi Breakout

    -Titulo Original : Adafruit ATWINC1500 WiFi Breakout-Fabricante : Adafruit-Descripcion Original: Connect your Arduino to the Internet with this fine new FCC-certified WiFi module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performance - running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer but we had to go to work, so we unplugged it). We like these so much, they've completely replaced the CC3000 module on all our projects. The Adafruit ATWINC1500 WiFi Breakout uses SPI to communicate, so with about 6 wires, you can get your wired up and ready to go. Right now the Atmel-supplied library works great with Arduino Zero, and seems to work OK on Uno but may not work on other Arduinos. You can clock it as fast as 12MHz for speedy, reliable packet streaming. And scanning/connecting to networks is very fast, a few seconds. This module works with 802.11b, g, or n networks & supports WEP, WPA and WPA2 encryption. The datasheet says it can do Soft-AP mode but we don't have any code to actually use that. Since this is our new favoritest SPI-protocol WiFi module we've decided to make a little breakout for it. The breakout comes with level shifting on all the input pins so you can use it with 3V or 5V logic. A 3.3V voltage regulator that can handle the 300mA spikes lets you power from 3-5.5VDC. There's also 3 LEDs that you can control over the SPI interface (part of the library code) or you can have controlled by the Arduino library. They'll light up when connected to an SSID, or transmitting data...
  • Adafruit Slim Sticker-type GSM/Cellular Quad-Band Antenna -
    Precio:  $42,329.00
    Expira: 17/07/2023
    Agregar al Carrito   Vista

    Adafruit Slim Sticker-type GSM/Cellular Quad-Band Antenna -

    -Titulo Original : Adafruit Slim Sticker-type GSM/Cellular Quad-Band Antenna - 3dBi uFL [ADA1991]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1991 // Stock Type: Wireless >> Antennas // In Stock & Ready to Ship // That's one slim cellular antenna! At just 75mm long from tip to tip and and with a thickness of just 2mm, this 3dBi GSM antenna is slim, compact and sensitive, with a 3dBi gain.  The antenna juts out from its base with stick-on back so you attach it to an enclosure if you're making something like, say, a DIY phone.  It has a tiny uFL connector on the end - which is perfect for the  FONA - but will also work well for any other RF project on the 850/900/1800/1900/2100 bands, such as any other Cellular or GSM/GPRS device.We also offer a version of this antenna with a longer 300mm cable ...
  • Adafruit AC, DC & Servo Motors Sub-Micro Servo SG51R (1 piec
    Precio:  $66,919.00
    Agregar al Carrito   Vista

    Adafruit AC, DC & Servo Motors Sub-Micro Servo SG51R (1 piec

    -Titulo Original : AC, DC & Servo Motors Sub-Micro Servo SG51R (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2201 // Stock Type: Robotics & CNC >> Robotics // In Stock & Ready to Ship // This is just about the cutest, tiniest little micro servo we could find, even smaller than the 9 gram micro servos we love so much.  It can rotate approximately 180 degrees (90 in each direction) and works just like the standard kind you're used to but  much smaller .   You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in small places. Of course, its not nearly as strong as a standard servo. Works great with the Motor Shield for Arduino or by just wiring up with the Servo library. Comes with a few horns and hardware. To control with an Arduino, we suggest connecting the orange control wire to pin 9 or 10 and using the  Servo library  included with the Arduino IDE ( see here for an example sketch ). Position 0 (1.5ms pulse) is middle, 90 (~2ms pulse) is all the way to the right, -90 (~1ms pulse) is all the way to the left...
  • Adafruit APDS9960 Proximity, Light, RGB, and Gesture Sensor
    Precio:  $55,949.00
    Agregar al Carrito   Vista

    Adafruit APDS9960 Proximity, Light, RGB, and Gesture Sensor

    -Titulo Original : Adafruit APDS9960 Proximity, Light, RGB, and Gesture Sensor-Fabricante : ADAFRUIT-Descripcion Original: This breakout is chock full o' sensors! Add basic gesture sensing, RGB color sensing, proximity sensing, or ambient light sensing to your project with the Adafruit APDS9960 Proximity, Light, RGB and Gesture Sensor. When connected to your microcontroller (running our library code) it can detect simple gestures (left to right, right to left, up to down, down to up are currently supported), return the amount of red, blue, green, and clear light, or return how close an object is to the front of the sensor. This device uses an I2C interface so it's easy to wire up and use. The APDS9960 from Avago Technologies has an integrated IR LED and driver, along with four directional photodiodes that sense reflected IR energy from the LED. It's proximity detection feature allows it to measure the distance an object is from the front of the sensor (up to a few centimeters) with 8 bit resolution...
  • Adafruit 4367 Circuit Playground TFT Gizmo - Bolt-on Display
    Precio:  $108,119.00
    Expira: 31/08/2022
    Agregar al Carrito   Vista

    Adafruit 4367 Circuit Playground TFT Gizmo - Bolt-on Display

    -Titulo Original : Adafruit 4367 Circuit Playground TFT Gizmo - Bolt-on Display Audio Amplifier-Fabricante : Adafruit-Descripcion Original: ets you add a lovely color display in a sturdy and reliable fashion // This PCB looks just like a round TFT breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections. // Once attached you'll get a 1.54" 240x240 IPS display with backlight control, // two 3-pin STEMMA connectors for attaching NeoPixel strips or servos, and a Class D audio amplifier with a Molex PicoBlade connector that can plug one of our lil speakers. // 53.3mm x 53.3mm x 9.4mm / 2.1" x 2.1" x 0.4" // Extend and expand your Circuit Playground projects with a bolt on TFT Gizmo that lets you add a lovely color display in a sturdy and reliable fashion. This PCB looks just like a round TFT breakout but has permanently affixed M3 standoffs that act as mechanical and electrical connections. Once attached you'll get a 1.54 240x240 IPS display with backlight control, two 3-pin STEMMA connectors for attaching NeoPixel strips or servos, and a Class D audio amplifier with a Molex PicoBlade connector that can plug one of our lil speakers. This is a great companion for our Circuit Playground Express or Bluefruit boards thanks to their fast SPI hardware speeds, and works in Arduino and CircuitPython. If you're using this with Circuit Playground Express and CircuitPython, you won't be able to do a lot because there isn't a ton of memory - mostly just displaying the REPL and maybe running an image slideshow. For CircuitPython use, the Bluefruit is recommended and works really great! You can use it with the Circuit Playground Classic in Arduino but it won't be very fast, as you have to bitbang the SPI - and the display has a lot of pixels - so it's not recommended. You'll have a very slow display. Comes with a PCB that has pre-soldered standoffs attached, and 12x M3 screws for attachment. Fits all Circuit Playgrounds but like we mentioned earlier, the Express and Bluefruit are recommended...
  • Adafruit 74LVC245 - Breadboard Friendly 8-bit Logic Level Sh
    Precio:  $30,769.00
    Agregar al Carrito   Vista

    Adafruit 74LVC245 - Breadboard Friendly 8-bit Logic Level Sh

    -Titulo Original : Adafruit 74LVC245 - Breadboard Friendly 8-bit Logic Level Shifter [ADA735]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 735 // Stock Type: Components & Parts >> IC & Transistors // In Stock & Ready to Ship // Most of our customers love using the Arduino for prototyping, design and invention but find themselves stuck when trying to connect the Arduino to the latest sensors, displays, controllers, interfaces, etc. as they are almost all 3.3V logic these days. We try to solve this problem by having all our breakout boards be 5V compatible or when that's not possible, including a level shifter chip but there are still thousands of tempting devices out there. This chip solves the problem of how to interface 3.3V logic devices to a 5.0V logic chip such as the Arduino. Most 3.3V devices do not like being run with 5V signals and can be damaged or flaky. The 74LVC245 is designed so that even when it runs at 1.8V, it still happily accepts 5V signals in one pin and converts it to a lower logic level on the opposite pin. This chip is only for digital signals, it doesn't convert analog signals (you need an op amp for that). It has 8 pipes it can convert but it won't work with bi-directional/pull-up based devices such as I2C or 1-Wire. It does work great for SPI, Serial, Parallel bus, and other logic interfaces. Using it is simple. We suggest checking out the 74LVC245 datasheet for details but essentially: connect VCC to your logic level you want to convert to (say 3.3V), Ground connects to Ground. Wire OE (output enable) to ground to enable the device and DIR (direction) to VCC. Then digital logic on the A pins up to 5V will appear on the B pins shifted down to the VCC logic...
  • Adafruit Small Enclosed Piezo w/Wires [ADA1740]
    Precio:  $24,339.00
    Expira: 08/09/2023
    Agregar al Carrito   Vista

    Adafruit Small Enclosed Piezo w/Wires [ADA1740]

    -Titulo Original : Adafruit Small Enclosed Piezo w/Wires [ADA1740]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1740 // Stock Type: Sensors >> Sound/Noise // In Stock & Ready to Ship // This small (14mm diameter) piezo element is nicely enclosed so you can attach easily. Piezo elements convert vibration to voltage or voltage to vibration. That means you can use this as a buzzer for making beeps, tones and alerts AND you can use it as a sensor, to detect fast movements like knocks. You can also use it under a drum pad to make a drum/crash sensor It's rated for up to 9Vpp use but you can also use 3V square waves and its plenty loud. For music use with an Arduino, check out the Tone tutorial . For sensing, the Knock tutorial is your guide! There are thin wires attached, we plugged them into a solderless breadboard, but they might too thin to plug in directly into the Arduino socket headers...
  • Adafruit FONA - Mini Cellular GSM Breakout - SMA Version [AD
    Precio:  $230,909.00
    Agregar al Carrito   Vista

    Adafruit FONA - Mini Cellular GSM Breakout - SMA Version [AD

    -Titulo Original : Adafruit FONA - Mini Cellular GSM Breakout - SMA Version [ADA1963]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1963 // Stock Type: Wireless >> Cellular // In Stock & Ready to Ship // Ring, Ring! Who's that callin'? It's your breadboard! Introducing Adafruit FONA MiniGSM, an adorable all-in-one cellular phone module that lets you add voice, text, SMS and data to your project in an adorable little package. This module measures only 1.75x1.25 but packs a surprising amount of technology into its little frame. At the heart is a GSM cellular module (we use the latest SIM800) the size of a postage stamp. This module can do just about everything. This version has an SMA connector. For the uFL version, click here! Quad-band 850/900/1800/1900MHz - connect onto any global GSM network with any 2G SIM (in the USA, T-Mobile is suggested)Make and receive voice calls using a headset OR an external 8Ω speaker + electret microphoneSend and receive SMS messagesSend and receive GPRS data (TCP/IP, HTTP, etc.)Scan and receive FM radio broadcasts (yeah, we don't exactly know why this was included but it works really well)PWM/Buzzer vibrational motor controlAT command interface with auto baud detectionSounds delicious, right? So we plated this fine module onto a little breakout with all the extras you need to make your next project shineOnboard LiPoly battery charging circuitry so you can take your project on the go. Use any 500mAh+ LiPoly or LiIon battery and recharge over the MicroUSB when necessary. Two LEDs let you know when its charging and doneStandard 4-pole TRRS headphone jack. Use any 'Android' or 'iPhone'-compatible headset with micBreakouts for external 8Ω speaker and electret mic if you don't want to use a headphoneLevel shifting circuitry so you can run it with 2.8V to 5V logic.Vibrational motor (buzzer) driver so you can have noiseless notificationsSMA connection for external antennaIndicator LEDs for power and network connectivity Standard SIM slides into the bac...
  • Adafruit 977 Accessories TO-220 Clip-On Heatsink 1 Piece
    Precio:  $43,489.00
    Expira: 07/10/2023
    Agregar al Carrito   Vista

    Adafruit 977 Accessories TO-220 Clip-On Heatsink 1 Piece

    -Titulo Original : Adafruit Accessories TO-220 Clip-On Heatsink (1 Piece)-Fabricante : Adafruit-Descripcion Original: Get the most out of your regulators, transistors and other TO-220 packaged chips by clipping on a heat-sink. Your transistor or regulator may advertise it can handle high currents but when multiplied by the drop voltage, the Wattage may be too high for the bare chip! Most TO-220's can disipate about 2W's worth without a sink...
  • Adafruit Fast Vibration Sensor Switch (Easy to Trigger) [ADA
    Precio:  $26,509.00
    Expira: 06/05/2023
    Agregar al Carrito   Vista

    Adafruit Fast Vibration Sensor Switch (Easy to Trigger) [ADA

    -Titulo Original : Adafruit Fast Vibration Sensor Switch (Easy to Trigger) [ADA1766]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1766 // Stock Type: Sensors >> Motion // In Stock & Ready to Ship // The poor man's accelerometer/motion sensor! These spring-vibration switches are non-directional vibration induced trigger switches. Inside is a very soft spring coiled around a long metal pin. When the switch is moved, the spring touches the center pole to make contact. So, when there's motion, the two pins will act like a closed switch. When everything is still, the switch is open. Great for basic projects and wearables! We also have a version with a slightly stiffer spring which makes it harder to trigger , and a version with a much more stiff spring which is even harder to trigger ...
  • Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board
    Precio:  $56,269.00
    Agregar al Carrito   Vista

    Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board

    -Titulo Original : Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board-Fabricante : ADAFRUIT-Descripcion Original: TB6612 motor driver // 1.2A per channel // Runs at 2.7V-5V logic. The motor voltage is separate from the logic voltage. Good for motor voltages from 4.5V up to 13.5V // Dimensions: 27mm x 19mm x 3mm / 1.1" x 0.7" x 0.1" // Weight: 1.8g // Spin two DC motors, step one bi-polar or uni-polar stepper, or fire off two solenoids with 1.2A per channel using the TB6612. These are perhaps better known as the drivers in our assembled Adafruit Motorshield or Motor HAT. We really like these dual H-bridges, so if you want to control motors without a shield or HAT these are easy to include on any solderless breadboard or perma-proto. We solder on TB6612 onto a breakout board for you here, with a polarity protection FET on the motor voltage input and a pullup on the standby enable pin. Each breakout chip contains two full H-bridges (four half H-bridges). That means you can drive 2-4 solenoids (only two can be active at a time, on opposite bridges), two DC motors bi-directionally, or one stepper motor. Just make sure they're good for 1.2 Amp or less of current, since that's the limit of this chip. They do handle a peak of 3A but that's just for a short amount of time, like 20 milliseconds. What we like most about this particular driver is that it comes with built in kick-back diodes internally so you dont have to worry about the inductive kick damaging your project or driver! There's two digital inputs per H-bridge (one for each half of the bridge) as well as a PWM input per driver so you can control motor speed. Runs at 2.7V-5V logic. The motor voltage is separate from the logic voltage. Good for motor voltages from 4.5V up to 13.5V! This wont work well for 3V motors. Comes as one assembled and tested breakout plus a small strip of header. You'll need to do some light soldering to attach the header onto the breakout PCB. Arduino, motors, and power supply not included. Check out our handy tutorial on assembly and wiring...
  • Adafruit Stereo Enclosed Speaker Set - 3w 4 Ohm
    Precio:  $60,049.00
    Expira: 23/03/2023
    Agregar al Carrito   Vista

    Adafruit Stereo Enclosed Speaker Set - 3w 4 Ohm

    -Titulo Original : Adafruit Stereo Enclosed Speaker Set - 3W 4 Ohm-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1669 // Stock Type: Components & Parts >> Speakers // In Stock & Ready to Ship // Listen up! This set of two 2.8 x 1.2 speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclosed for good audio volume and quality. The pair have a handy SPK input cable to add audio to your displays (the connectors are similar to the JST-PH series  which is ~2.0mm spacing). We're specifically carrying these to use with our 10.1 inch , 7 inch , or 5.6 inch 1280x800 Display w/ Audio driver boards. However, they work peachy-keen with any of our audio amps as well, such as the MAX98306 , TS2012 or TPA2016 stereo class D amplifiers...
  • Adafruit 3229 Radio FeatherWing - RFM69HCW 900MHz
    Precio:  $77,039.00
    Agregar al Carrito   Vista

    Adafruit 3229 Radio FeatherWing - RFM69HCW 900MHz

    -Titulo Original : Adafruit (PID 3229 Radio FeatherWing - RFM69HCW 900MHz-Fabricante : Adafruit-Descripcion Original: SX1231 based module with SPI interface // Packet radio with ready-to-go Arduino libraries // Uses the license-free ISM bands // +13 to +20 dBm up to 100 mW Power Output Capability (power output selectable in software) // 50mA (+13 dBm) to 150mA (+20dBm) current draw for transmissions // Add short-hop wireless to your Feather with these Radio Featherwings. These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x's). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. These radio modules come in four variants (two modulation types and two frequencies) The RFM69's are easiest to work with, and are well known and understood. The LoRa radios are exciting, longer-range and more powerful but also more expensive. RFM69 @ 433 MHz - basic packetized FSK/GFSK/MSK/GMSK/OOK radio at 433 MHz for use in Europe ITU 1 license-free ISM, or for amateur use with restrictions (check your local amateur regulations!) RFM69 @ 900 MHz - basic packetized FSK/GFSK/MSK/GMSK/OOK radio at 868 or 915 MHz for use in Americas ITU 2 license-free ISM, or for amateur use with restrictions (check your amateur regulations!) RFM98 @ 433 MHz - LoRa capable radio at 433 MHz for use in Europe ITU 1 license-free ISM, or for amateur use with restrictions (check your local amateur regulations!) RFM95 @ 900 MHz - LoRa capable radio at 868 or 915 MHz for use in Americas ITU 2 license-free ISM, or for amateur use with restrictions (check your local amateur regulations!) This is the RFM69 @ 900 MHz version, it can be used for 868 MHz or 915 MHz (the radios use software configured frequency) These are +20dBm FSK packet radios that have a lot of nice extras in them such as encryption and auto-retransmit. They can go at least 500 meters line of sight using simple wire antennas, probably up to 5Km with directional antennas and settings tweaking...
  • Adafruit 3346 I2S 3W Stereo Speaker Bonnet For Raspberry Pi
    Precio:  $71,619.00
    Agregar al Carrito   Vista

    Adafruit 3346 I2S 3W Stereo Speaker Bonnet For Raspberry Pi

    -Titulo Original : Adafruit (PID 3346 I2S 3W Stereo Speaker Bonnet For Raspberry Pi - Mini Kit-Fabricante : Adafruit-Descripcion Original: 3W Stereo Amplifier Bonnet for Raspberry Pi // I2S digital sound standard interface // Plug any 4 ohm or 8 ohm speakers // Operating Voltage: 5V (2.4A for 3W 4 ohm speakers) // Works with Raspberry Pi with 2x20 headers (A+, B+, Zero, Pi 2, Pi 3, etc) // Hey Mr. DJ! Turn up that Raspberry Pi mix to the max with this cute 3W Stereo Amplifier Bonnet for Raspberry Pi. (It's not big enough to be an official HAT, so we called it a bonnet, you see?) It's the exact same size as a Raspberry Pi Zero but works with any and all Raspberry Pi computers with a 2x20 connector - A+, B+, Zero, Pi 2, Pi 3, etc. We've tested it out with Raspbian (the offical operating system) and Retropie. This Bonnet uses I2S a digital sound standard, so you get really crisp audio. The digital data goes right into the amplifier so there's no static like you hear from the headphone jack. And it's super easy to get started. Just plug in any 4Ω to 8Ω speakers, up to 3 Watts, run our installer script on any Raspberry Pi, reboot and you're ready to jam! Each order comes as a fully tested PCB with a 2x20 header and 2x terminal blocks. Some light soldering is required to attach the header onto PCB so you can plug it into your Raspberry Pi. Once that's done either plug one of our enclosed speaker sets right into the JST jack in the middle or you can solder the terminal blocks in and then connect any speaker you like like our 4Ω 3W or 8Ω 1W. Hey you can even use a surface transducer! Our tutorial will get you set up with instructions, you'll be rockin' out in 15 minutes. Don't forget to make sure you have a good strong 5V power supply - especially if you're using the 3W 4 ohm speakers! Our 2.4A power plug is recommended. Pi Zero and speakers not included...
  • Adafruit Flora RGB Smart NeoPixel Version 2 - Pack of 4 [ADA
    Precio:  $66,349.00
    Expira: 10/02/2021
    Agregar al Carrito   Vista

    Adafruit Flora RGB Smart NeoPixel Version 2 - Pack of 4 [ADA

    -Titulo Original : Adafruit Flora RGB Smart NeoPixel Version 2 - Pack of 4 [ADA1260]-Fabricante : ADAFRUIT-Descripcion Original: Flora NeoPixels // Designed specifically for wearables // ultra-bright LED (each pixel can draw as much as 60mA) // High Speed 800KHz communication // Full 24-bit color ability with PWM taken care of by the controller chip // What's a wearable project without LEDs? Our favorite part of the Flora platform is these tiny smart pixels. Designed specifically for wearables, these updated Flora NeoPixels have ultra-cool technology: these ultra-bright LEDs have a constant-current driver cooked right into the LED package! The pixels are chainable - so you only need 1 pin/wire to control as many LEDs as you like. They're easy to sew, and the chainable design means no crossed threads. This is the second version of the Flora NeoPixels, which runs at at 'high speed' 800KHz communication. Unfortunately they are not back-compatible with the chip-on-back 'low speed' (400KHz) Flora NeoPixels. If you have a project that already uses low speed pixels, and you want to attach more pixels to the chain, you will need to purchase version 1's as these are not cross-compatible. These pixels have full 24-bit color ability with PWM taken care of by the controller chip. Since the LED is so bright, you need less current/power to get the effects you want. The driver is constant current so its OK if your battery power changes or fluctuates a little. Each pixel draws as much as 60mA (all three RGB LEDs on for full brightness white). In theory, the Flora can drive up to 500 pixels at 30 FPS (it will run out of RAM after that). However, after about 10 pixels (or if the distance between pixels is more than an inch or two) the resistance of the thread can affect the power supply. For large quantities of pixels over 10, you may want to consider using stranded core wire or copper braid to provide a power bus for the pixels - the current draw will add up fast! Each order comes with 4 individually controllable pixels...
  • Adafruit Bluefruit Le Sniffer - Bluetooth Low Energy (ble 4
    Precio:  $122,389.00
    Expira: 12/12/2021
    Agregar al Carrito   Vista

    Adafruit Bluefruit Le Sniffer - Bluetooth Low Energy (ble 4

    -Titulo Original : Adafruit Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v2.0 [ADA2269]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2269 // Stock Type: Wireless >> Bluetooth // In Stock & Ready to Ship // Interested in learning how Bluetooth Low Energy works down to the packet level? Debugging your own BLE hardware, and trying to spot where something is going wrong? Or maybe you're writing a custom application for your phone or tablet that needs to talk to existing BLE hardware, but you don't know how it works beneath the surface? We have the perfect tool for you!This Bluefruit LE Friend is programmed with a special firmware image that turns it into an easy to use Bluetooth Low Energy sniffer. You can passively capture data exchanges between two BLE devices, pushing the data into Wireshark, the open source network analysis tool, where you can visualize things on a packet level, with useful descriptors to help you make sense of the values without having to crack open the 2000 page Bluetooth 4.0 Core Specification every time.Plug it into your development machine, fire up the special sniffer bridge SW, select the device you want to sniff, and it will fire up Wireshark for you and start pushing data in via a live stream (using Nordic's Windows software), or save to a pcap file that you can analyze with Wireshark later. Please Note :  You can only use this device to listen on Bluetooth Low Energy devices! It will not work on Bluetooth (classic) devices. The Nordic Wireshark-streaming sniffer software is currently Windows only. We have example code using the python API that will work on any OS to log the sniffed data to a pcap file for analysis so you can use this sniffer with any OS with python.The sniffer firmware cannot be used with the the Nordic DFU bootloader firmware, which means that if you want to reprogram this devices you must use a J-Link (and, likely, a SWD adapter + SWD Breakout ) You cannot over-the-air reprogram it. Check out our tutorial for more details and software downloads...
  • Adafruit 284 FTDI Friend Extras ADA284
    Precio:  $76,599.00
    Agregar al Carrito   Vista

    Adafruit 284 FTDI Friend Extras ADA284

    -Titulo Original : Adafruit FTDI Friend Extras [ADA284]-Fabricante : Adafruit-Descripcion Original: Long gone are the days of parallel ports and serial ports. Now the USB port reigns supreme! But USB is hard, and you just want to transfer your every-day serial data from a microcontroller to computer. What now? Enter the FTDI Friend! The FTDI Friend is a tweaked out FTDI FT232RL chip adapter. Sure, like the well-known FTDI cable, it can provide power to your project and there are 4 signal lines for sending data back and forth. But the Friend can do much more! For example, you can change the signal and power lines to be either 3.3V or 5V. Arduino-derivatives and XBees use the RTS line for programming but what if you need that DTR line? It's there for you. By default, it's setup so that it matches Adafruit's FTDI cables. The 6th pin is RTS (as of Arduino IDE v18 this will work perfectly for uploading to 'inos), the power wire is +5V and the signal levels are 3.3V. You can even rearrange the wire order with a 6-pin extension cable (not included). In a pinch, you can use it to program AVRs (its a bit slow but works!) Item Specifics Length: 38.07mm/1.5in Width: 17.89mm/0.7in Height: 7.7mm/0.31in Weight: 3.4g/0.12o...
Mostrar del 1 al 24 (de 177 productos)
Páginas de Resultados:  1  2  3  4  5 ...  [Siguiente >>] 
Destacados
Revisar todos destacados

Información

Información

Nuestras ofertas

Nuestras ofertas

Su cuenta

Su cuenta

Mantente conectado

Mantente conectado

Contáctenos

Contáctenos

elbazardigital.com   © 2024