Arriba

Inicio » Catalogo » Electrónica, Audio y Video » Componentes Electrónicos > Semiconductores > Circuitos Integrados

Componentes Electrónicos > Semiconductores > Circuitos Integrados

Mostrar: 
Mostrar del 1 al 24 (de 178 productos)
Páginas de Resultados:  1  2  3  4  5 ...  [Siguiente >>] 
  • Adafruit Magnetic contact switch (door sensor) [ADA375]
    Precio:  $46,349.00
    Agregar al Carrito   Vista

    Adafruit Magnetic contact switch (door sensor) [ADA375]

    -Titulo Original : Adafruit Magnetic contact switch (door sensor) [ADA375]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 375 // Stock Type: Sensors >> Proximity // In Stock & Ready to Ship // This sensor is essentially a reed switch, encased in an ABS plastic shell. Normally the reed is 'open' (no connection between the two wires). The other half is a magnet. When the magnet is less than 13mm (0.5) away, the reed switch closes. They're often used to detect when a door or drawer is open, which is why they have mounting tabs and screws. You can also pick up some double-sided foam tape from a hardware store to mount these, that works well without needing screws...
  • Adafruit Electroluminescent (EL) Panel - 10cm x 10cm Blue [A
    Precio:  $70,529.00
    Expira: 24/02/2023
    Agregar al Carrito   Vista

    Adafruit Electroluminescent (EL) Panel - 10cm x 10cm Blue [A

    -Titulo Original : Adafruit Electroluminescent (EL) Panel - 10cm x 10cm Blue [ADA624]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 624 // Stock Type: EL Wire/Tape/Panel >> EL Panels // In Stock & Ready to Ship // EL panel is the big sister to EL wire - it has the same glow effect but with a flat shape instead of a round shape. This is a big sheet of flexible plastic coated with EL material so its like one big glowing square. It emits an even glow over the entire shape. The glowing part of the panel is 10 cm x 10 cm (approx: 4 x 4). There's a plastic coating is about 10.4cm x 10.4cm. Its covered in what seems to be PVC, the tape is thus weather-proof - but note that the connectors are NOT waterproof, just a bit of heatshrink. This isn't something we would suggest leaving outdoors for extended periods. You can attach it by sewing through the clear plastic edging, or gluing the back to a flat surface. It is flexible but will crease and damage if folded. You can cut the panel up as long as the shape you cut out is continuous and has the JST cable attached. This panel is a blue color when lit and appears blue when off. Because EL tape has more surface area than wire, it requires a more powerful inverter. We suggest you use our 4xAAA inverter which is strong enough to power a single panel at once - plug it in and turn it on! For more permanent installations, the 12V EL inverter can also power a single panel and run off 8xAA batteries or a wall adapter....
  • Adafruit Mini Lipo w/Mini-B USB Jack - USB LiIon/LiPoly Char
    Precio:  $47,149.00
    Agregar al Carrito   Vista

    Adafruit Mini Lipo w/Mini-B USB Jack - USB LiIon/LiPoly Char

    -Titulo Original : Adafruit Mini Lipo w/Mini-B USB Jack - USB LiIon/LiPoly Charger - v1-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1905 // Stock Type: Power >> LiIon & LiPoly >> Chargers // In Stock & Ready to Ship // Adafruit Mini Lipo w/Mini-B USB Jack - USB LiIon/LiPoly charger - v1 Adafruit Product ID: 1905. Battery not included...
  • Adafruit 3988 Prop Maker FeatherWing
    Precio:  $60,609.00
    Agregar al Carrito   Vista

    Adafruit 3988 Prop Maker FeatherWing

    -Titulo Original : Adafruit (3988 Prop Maker FeatherWing-Fabricante : Adafruit-Descripcion Original: The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. Snap-in NeoPixel port - With a 3-pin JST connector, you can plug in one of our JST-wired NeoPixel strips directly, or use a 3-pin JST connector to wire up your favorite shape of addressable NeoPixel LEDs. This port provides high current drive from either the Feather Lipoly or USB port, whichever is higher. A level shifter gives you a clean voltage signal to reduce glitchiness no matter what chip you're using 3W RGB LED drivers - 3 high current MOSFETs will let you connect a 3W RGB LED for powerful eye-blasting glory. For most Feathers, the 3 pins are PWM capable so you can generate any color you like. Available as pin breakouts plus strain-relief holes Triple-Axis Accelerometer with Tap Detection - The LIS3DH is our favorite accelerometer, you can use this for detection motion, tilt or taps. Here's an example of a light saber that makes sounds when swung or hit. We have code for this chip in both Arduino and CircuitPython. Class D Audio Amplifier - Drive a 8Ω 1Watt speaker or 4Ω 3W speaker for sound effects. Plug and play with our cute and slim oval speaker, or connect a picoblade cable for your favorite speaker. For use only with Feathers that have analog audio out such as the Feather M0 Express and M4 series. Low power mode! The power system for the RGB LED, NeoPixels and speaker amplifier can be controlled by a pin to cut power to them, so you have lower power usage when the prop is in sleep or off mode (but can wake up fast by listening to the button press or accelerometer data). When the power pin is set low, the current draw for just the wing is under 1mA and no there's current draw from any attached NeoPixel...
  • Adafruit 3966 BMP388 - Precision Barometric Pressure And Alt
    Precio:  $66,399.00
    Agregar al Carrito   Vista

    Adafruit 3966 BMP388 - Precision Barometric Pressure And Alt

    -Titulo Original : Adafruit BMP388 - Precision Barometric Pressure And Altimeter (3966)-Fabricante : Adafruit-Descripcion Original: Product Dimensions: 21.6mm x 16.6mm x 3.0mm / 0.9" x 0.7" x 0.1" // Product Weight: 1.2g / 0.0oz // Bosch has been a leader in barometric pressure sensors, from the BMP085. BMP180, and BMP280... now we've got the next generation, the Adafruit BMP388 Precision Barometric Pressure sensor. As you would expect, this sensor is similar to its earlier versions but even better. The BMP388 has better precision than ever, which makes it excellent for environmental sensing or as a precision altimeter. It can even be used in either I2C and SPI configurations. The BMP3xx is the next-generation of sensors from Bosch, and is the upgrade to the BMP280 - with a low altitude noise as low as 0.1m and the same fast conversion time. And like the previous BMP280, you can use I2C or SPI. For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI. This sensor has a relative accuracy of 8 Pascals, which translates to about ± 0.5 meter of altitude (compare to the BMP280's 12 Pascal/ ±1 meter). The datasheet sort of implies they intend this sensor to be used for drones and quadcopters, to keep altitude stable, but you could also use this for wearables or any project that wants to track height-above-sea-level. Note that for absolute height you'll still need to enter in the barometric pressure at sea level, if the weather changes, but that's true of every altimeter sensor that uses pressure. You can also measure temperature with ±0.5°C accuracy. Nice sensor right? So we made it easy for you to get right into your next project. The surface-mount sensor is soldered onto a PCB and comes with a 3.3V regulator and level shifting so you can use it with a 3V or 5V logic microcontroller without worry. Check out the Arduino library to get data out in under 10 minutes...
  • Adafruit Ir Distance Sensor Includes Cable (10cm-80cm) - Gp
    Precio:  $82,499.00
    Agregar al Carrito   Vista

    Adafruit Ir Distance Sensor Includes Cable (10cm-80cm) - Gp

    -Titulo Original : Adafruit IR distance sensor includes cable (10cm-80cm) - GP2Y0A21YK0F [ADA164]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 164 // Stock Type: Sensors >> Proximity // In Stock & Ready to Ship // This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how close the nearest object is. Comes with 12 long 3-JST interface wire. These sensors are good for short-range detection. For over 1 m distance, we suggest using sonar sensorsTo use, connect black wire to ground, red wire to 5V and white wire to analog input. The analog voltage out will range from 3V when an object is only 4 (10 cm) away and 0.4V when the object is 32 (80 cm) awayFor more information, please see the datasheet ...
  • Rampa portátil DMI para silla de ruedas, Portátil y Ligera
    Precio:  $691,979.00
    Agregar al Carrito   Vista

    Rampa portátil DMI para silla de ruedas, Portátil y Ligera

    -Titulo Original : DMI Wheelchair Ramp,Entry Ramp,Threshold Ramp And Handicap Ramp Is Portable And Adjustable From 3-5 Ft Long, 4.5 In Wide For Entryway,Doors,Steps,Shed Or Curb,Storage Bag And 2 Ramps Included-Fabricante : DMI-Descripcion Original: - LA RAMPA PARA SILLA DE RUEDAS TIENE UNA SUPERFICIE ANTIDESLIZANTE SEGURA Y DURADERA y es portátil para uso en interiores o exteriores, ya sea en casa o mientras viaja. La rampa es perfecta para escalones, bordillos, cobertizos, entradas o acceso de vehículos para mejorar la seguridad, la estabilidad y la independencia - LA RAMPA PARA HANDICAP es ajustable y retráctil. Las rampas se ajustan de 3 a 5 pies de largo y tienen 7 pulgadas de ancho y el área interior mide 4,5 pulgadas de ancho para adaptarse a una rueda de no más de 4 pulgadas. Los rieles laterales tienen una altura de 2,25 pulgadas para eliminar el deslizamiento - LA RAMPA PORTÁTIL ES RESISTENTE AL ÓXIDO, duradera y liviana. Cada rampa puede soportar hasta 300 libras para un total de 600 libras. Mover, transportar y almacenar las rampas es fácil y sin esfuerzo, ya que solo pesan 6 libras cada una. - RAMPA DE ACCESO A LA RAMPA DE ENTRADA presenta un ensamblaje rápido y fácil sin herramientas para acceder a cualquier lugar para hacer una solución de movilidad segura y duradera temporal, portátil o permanente - RAMPA PARA SILLA DE RUEDAS PARA HOGAR incluye 2 rampas con bolsa de almacenamiento. Asegúrese de medir las ruedas para asegurarse de que no tengan más de 4 pulgadas de ancho. El producto debe ser utilizado por sillas de ruedas ocupadas con la ayuda de otra persona. - Para ser utilizado por sillas de ruedas ocupadas con la asistencia de otra persona - No recomendado para scooters o sillas eléctricas, o aquellos con ruedas desplazadas o menos de 2,5 pulgadas de distancia al suelo del anillo de empuje Las rampas ajustables para sillas de ruedas más vendidas son perfectas para el hogar, ya que los usuarios de sillas de ruedas pueden entrar y salir fácilmente en áreas interiores o exteriores que necesitan asistencia de rampa. Los usuarios de sillas de ruedas también las encontrarán invaluables cuando visiten a amigos o familiares que pueden no tener entradas accesibles. Ligeras y compactas , estas rampas portátiles son fáciles de transportar o almacenar en la cajuela de un automóvil. Cada rampa pesa solo 6 libras, lo que las hace fáciles de levantar y colocar. Se extienden de 3 a 5 pies, para usar en diferentes tamaños y alturas de escalones. La rampa puede soportar 300 libras (600 libras en total entre ellas). Cómo usar Se incluyen dos rampas. Para extender las rampas, tire de las secciones uno y dos hasta que los botones de bloqueo estén completamente extendidos en los orificios y encajen en su lugar. Después del uso, simplemente retírelos y guárdelos en su práctica bolsa de transporte de nailon.Cómo medir las rampas para sillas de ruedasPara calcular la longitud de la rampa, necesitará medir la altura.La altura es la medida entre el suelo y donde Se colocará la parte superior de la rampa. La Ley de Estadounidenses con Discapacidades (ADA, por sus siglas en inglés) exige que las áreas públicas tengan rampas para sillas de ruedas con una inclinación de 4,8 grados o menos (una proporción de 1:12). Esto equivale a un pie de rampa por cada pulgada de elevación. Para áreas residenciales como viviendas, la ADA recomienda una pendiente de 2:12. Esto equivale a un pie de rampa por cada dos pulgadas de elevación. Para calcular la longitud de la rampa, dividirá la subida por dos. Para uso doméstico, estas rampas funcionarían para elevaciones de hasta 10 pulgadas. A continuación, debe medir el ancho de las ruedas. Estas rampas tienen un área de vía interior de 4,5 pulgadas. Asegúrese de que cada rueda no tenga más de 4 pulgadas de ancho...
  • Adafruit Micro Lipo w/MicroUSB Jack - USB LiIon/LiPoly charg
    Precio:  $38,159.00
    Agregar al Carrito   Vista

    Adafruit Micro Lipo w/MicroUSB Jack - USB LiIon/LiPoly charg

    -Titulo Original : Adafruit Micro Lipo w/MicroUSB Jack - USB LiIon/LiPoly charger - v1 [ADA1904]-Fabricante : ADAFRUIT-Descripcion Original: Battery not included // Adafruit Micro Lipo w/MicroUSB Jack - USB LiIon/LiPoly charger - v1 Adafruit Product ID: 1904. Battery not included...
  • Adafruit 4258 LPS35HW Water Resistant Pressure Sensor
    Precio:  $78,479.00
    Agregar al Carrito   Vista

    Adafruit 4258 LPS35HW Water Resistant Pressure Sensor

    -Titulo Original : Adafruit 4258 LPS35HW Water Resistant Pressure Sensor-Fabricante : Adafruit-Descripcion Original: water resistant barometric pressure and temperature sensor that is also safe to use in wet environments // should work well for normal wet situations like weather stations or high humidity // 260 to 1260 hPa absolute pressure range // 24-bit pressure data output -- ODR from 1 Hz to 75 H // 16-bit temperature data output -- SPI and I²C interfaces // Sometimes you need to sense pressure in a damp environment. And sometimes you need to know the relative changes in pressure as well as the absolute pressure. For the times you need to do both (or either), the LPS35HW is the pressure sensor for you. Combining protection from water intrusion with support for high precision relative and absolute measurements, this sensor will do what you need. With drivers for CircuitPython, Arduino, and Raspberry Pi, and support for I2C or SPI (Arduino only SPI support, for now) you'll be measuring pressure in moist situations in no time. The ST LPS35HW is a water resistant barometric pressure and temperature sensor that is also safe to use in wet environments. The sensing element is nestled safely in a ceramic package and is encased in a waterproof gel that prevents water that gets into the sensor from interfering with readings. It does not carry any ratings for resistance to moisture so you probably don't want to take it to the bottom of the Mariana Trench, but it should work well for normal wet situations like weather stations or high humidity. Along with not being afraid of getting wet, the LPS35HW has a 24bit pressure data and 16 bit temperature data, allowing it to deliver pressure readings with +/- 0.1% hPa accuracy. It can measure from 260 to 1260 hPa and is able to withstand pressure up to 20 times its measurement range. To help you take measurements to your requirements, the LPS35HW also offers an adjustable data rate, as well as a low pass filter to remove noise from the signal. Finally, the onboard temperature compensation makes sure that your readings are always good and won't vary as the temperature changes. We placed this sensor on a breakout board with a 3.3V regulator and level shifting circuitry so it can be used by 3V or 5V power/logic devices. A small piece of header is also included, so you can solder it in for use with a breadboard...
  • 0.5mm Pitch 24 Pins To 24 Pin Extension Cable Ffc Fpc
    Precio:  $44,499.00
    Expira: 01/01/2022
    Agregar al Carrito   Vista

    0.5mm Pitch 24 Pins To 24 Pin Extension Cable Ffc Fpc

    -Titulo Original : uxcell 0.5mm Pitch 24 Pins to 24 Pin Extension Connector Aapter for FFC FPC Cable Extend Zip HDD-Fabricante : uxcell-Descripcion Original: 461/5000 [Especificación]: paso de 24 pines a 24 pines de 0.5 mm para cable FFC de 24 pines [Característica]: Soporte de PCB de placa de extensión FPC, conexión de placa de botón / placa de convertidor a placa base [Tipo]: Este es un adaptador de extensión de conector FPC de paso de 0,5 mm para una instalación más larga. [Paquete]: 1 x Pin a Pin Adaptador de extensión de conector FPC de paso de 0,5 mm [Aplicación]: FPC está encontrando una amplia aceptación en la industria informática, particularmente en aplicaciones como la computadora portátil Lap Top, Palm Top y Note Pad...
  • Adafruit L3GD20H Triple-Axis Gyro Breakout Board - L3GD20/L3
    Precio:  $62,259.00
    Agregar al Carrito   Vista

    Adafruit L3GD20H Triple-Axis Gyro Breakout Board - L3GD20/L3

    -Titulo Original : Adafruit L3GD20H Triple-Axis Gyro Breakout Board - L3GD20/L3G4200 Upgrade - L3GD20H [ADA1032]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1032 // Stock Type: Sensors >> Motion // In Stock & Ready to Ship // A gyroscope is a type of sensor that can sense twisting and turning motions. Often paired with an accelerometer, you can use these to do 3D motion capture and inertial measurement (that is - you can tell how an object is moving!) As these sensors become more popular and easier to manufacture, the prices for them have dropped to the point where you can easily afford a triple-axis gyro! Only a decade ago, this space-tech sensor would have been hundreds of dollars. This breakout board is based around the latest gyro technology, the L3GD20H from STMicro . It's the upgrade to the L3G4200 ( see this app note on what to look for if upgrading an existing design to the L3GD20 ) with three full axes of sensing. The chip can be set to ±250, ±500, or ±2000 degree-per-second scale for a large range of sensitivity. There's also built in high and low pass sensing to make data processing easier. The chip supports both I2C and SPI so you can interface with any microcontroller easily. Since this chip is a 3.3V max device, but many of our customers want to use it with an Arduino, we soldered it to a breakout board with level shifting circuitry so you can use the I2C or SPI interface safely using a 5V interface device. We also place a 3.3V regulator on there so you can power it from 5V. Since we expect people will want to attach it firmly to their project, the PCB comes with four 2.1mm mounting holes. Use #2-56 imperial or M2 screws screws. Getting started is easy - simply connect SDA to your Arduino I2C data pin (On the UNO this is A4), SCL to I2C clock (Uno: A5), GND to ground, and Vin to 3 or 5VDC. Then install and run our easy to use Arduino library, which will print out the XYZ sensor data to the serial terminal. Our library also supports SPI on any 4 digital I/O pins, see the example for wiring...
  • Adafruit 259 , USB Li-Ion/LiPoly Charger, v1.2
    Precio:  $71,939.00
    Agregar al Carrito   Vista

    Adafruit 259 , USB Li-Ion/LiPoly Charger, v1.2

    -Titulo Original : Adafruit 259 , USB Li-Ion/LiPoly Charger, v1.2-Fabricante : ADAFRUIT-Descripcion Original: Comes assembled and tested with a free bonus jst cable // For charging single lithium ion/lithium polymer // Weight: 5.7G ( 0.2Oz) // Chip supports a 10K ntc thermistor which we have stuffed as a plain 10K. For people who require temperature monitors (using high charge rates), remove the 10K and solder in the thermistor in its place // 0.1 inch // This is a lithium ion and lithium polymer battery charger based on the MCP73833. It uses a USB mini-b for connection to any computer or 'USB wall adapter'. charging is done in three stages: first a preconditioning charge, then a constant-current fast charge and finally a constant-voltage trickle charge to keep the battery topped-up. The fast-charge current is 500MA by default, but is easily adjustable from 100MA up to 1000MA by soldering a through-hole resistor on-board. This board is great for DIY projects because it has 3 indicator LEDs - one for power, one for charging status and a third that indicates when charging is complete. You may also keep the battery connected to the charger and pass power through the additional jst connector using the included cable...
  • Adafruit 3357 Music Maker FeatherWing - MP3 OGG WAV MIDI Syn
    Precio:  $90,729.00
    Agregar al Carrito   Vista

    Adafruit 3357 Music Maker FeatherWing - MP3 OGG WAV MIDI Syn

    -Titulo Original : Adafruit (PID 3357 Music Maker FeatherWing - MP3 OGG WAV MIDI Synth Player-Fabricante : Adafruit-Descripcion Original: Features the VS1053B codec chip - decodes Ogg Vorbis, MP3/MP2/MP1, MP4, AAC, WMA, FLAC, WAV/PCM, MIDI. // SPI Interface // Can play audio from an uSD (micro SD) card // FAT16/FAT32 formatted SD card // Built-in MIDI synth/drum machine with dozens of instruments // Bend all audio files to your will with the Adafruit Music Maker FeatherWing! It's a fun-size version of our Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). You can do all sorts of stuff with the audio as well such as adjusting bass, treble, and volume digitally. All this functionality is implemented in a light-weight SPI interface so that any Feather Board can play audio from an SD card. There's also a special MIDI mode that you can boot the chip into that will read 'classic' 31250Kbaud MIDI data from the UART TX pin and act like a synth/drum machine - there are dozens of built-in drum and sample effects! What a great musical add-on to your Feather! That's why we spun up this super FeatherWing, perfect for use with a great many of our Feather Boards! Here are some specs: Features the VS1053B codec chip - decodes Ogg Vorbis, MP3/MP2/MP1, MP4, AAC, WMA, FLAC, WAV/PCM, MIDI. Stereo audio out with proper audio filter caps and ground reference so it can be safely connected directly to headphones, a stereo system or other powered speakers MicroSD card socket, for any FAT16/FAT32 formatted SD card from 64MB or greater Built in MIDI synth/drum machine with dozens of instruments Each order comes with one tested FeatherWing, and two sticks of 0.1 male headers to plug it into your Feather. Some light soldering is required to attach the through-hole headers to the PCB for plugging into your Feather Board. Headphones, SD card and Feather Board not included...
  • Adafruit Speakers & Transducers Thin Plastic Speaker w/Wires
    Precio:  $29,879.00
    Expira: 14/08/2021
    Agregar al Carrito   Vista

    Adafruit Speakers & Transducers Thin Plastic Speaker w/Wires

    -Titulo Original : Speakers & Transducers Thin Plastic Speaker w/Wires - 8 ohm 0.25W (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1891 // Stock Type: Components & Parts >> Speakers // In Stock & Ready to Ship // Listen up! This 1.5 diameter speaker cone is the perfect addition to any audio project where you need an 8Ω impedance and are using 0.25W of power. The speakers are rated at 0.25W, with a maximum input of 0.5W (printed wattage on back of speaker may have either value).We particularly like this cone as it's very simple and its plastic body is extremely lightweight and thin. Originally designed for 'talking' greeting cards, its fairly loud yet lightweight. Works great with our Wave shield or class D amplifier board . Just be careful not to overdrive the speaker as high volumes can blow it out! Start with lower volume and increase carefully...
  • Adafruit Small Enclosed Piezo w/Wires [ADA1740]
    Precio:  $24,339.00
    Expira: 08/09/2023
    Agregar al Carrito   Vista

    Adafruit Small Enclosed Piezo w/Wires [ADA1740]

    -Titulo Original : Adafruit Small Enclosed Piezo w/Wires [ADA1740]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1740 // Stock Type: Sensors >> Sound/Noise // In Stock & Ready to Ship // This small (14mm diameter) piezo element is nicely enclosed so you can attach easily. Piezo elements convert vibration to voltage or voltage to vibration. That means you can use this as a buzzer for making beeps, tones and alerts AND you can use it as a sensor, to detect fast movements like knocks. You can also use it under a drum pad to make a drum/crash sensor It's rated for up to 9Vpp use but you can also use 3V square waves and its plenty loud. For music use with an Arduino, check out the Tone tutorial . For sensing, the Knock tutorial is your guide! There are thin wires attached, we plugged them into a solderless breadboard, but they might too thin to plug in directly into the Arduino socket headers...
  • Adafruit Drv8871 Dc Motor Driver Breakout Board - 3.6a Max
    Precio:  $60,769.00
    Agregar al Carrito   Vista

    Adafruit Drv8871 Dc Motor Driver Breakout Board - 3.6a Max

    -Titulo Original : Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A Max-Fabricante : ADAFRUIT-Descripcion Original: Crank up your robotics with powerful Adafruit DRV8871 motor driver breakout board. This motor driver has a lot of great specs that make it useful for a wide variety of mechatronics. In particular, the simple resistor-set current limiting and auto-magic PWM support make it super easy to use with just about any brushed DC motor. Check out the specs for the DRV8871: 6.5V to 45V motor power voltage Up to 5.5V logic level on IN pins 565mΩ Typical RDS(on) (high + low) 3.6A peak current PWM control Current limiting/regulation without an inline sense resistor Undervoltage lockout Overcurrent protection Thermal shutdown Using it is super simple. Connect your motor to the OUT terminal block. Power the board with 6.5-45VDC power on VMotor and provide the H-bridge input control on IN1 and IN2. You can even PWM the inputs and the driver chip will do the right thing. You can set the current limiting with an external resistor Rlim. We solder in a 30K resistor by default for a ~2A current limit, however you can remove this resistor and/or solder a resistor over it to change the resistance and change the limit. Each order comes with one fully assembled and tested motor driver breakout, two 2-pin terminal blocks and a small strip of header. Some light soldering is required to attach the header and terminal blocks but its a simple task that can be done with basic soldering equipment. Technical Details Product Dimensions: 24.4mm x 20.4mm x 9.7mm / 1.0 x 0.8 x 0.4 Product Weight: 2.2g / 0.1o...
  • Adafruit 2359 Raspberry Pi A Case - Smoke Base W/Clear Top
    Precio:  $46,989.00
    Agregar al Carrito   Vista

    Adafruit 2359 Raspberry Pi A Case - Smoke Base W/Clear Top

    -Titulo Original : Adafruit 2359 Raspberry Pi A Case - Smoke Base W/Clear Top-Fabricante : Adafruit-Descripcion Original: Case Dimensions (without lid): 73mm x 63mm x 26mm / 2.9" x 2.5" x 1" // Lid Thickness: 4mm / 0.2" // 39g // It took awhile to perfect - but that's okay since we can now safely say that the Adafruit case for Raspberry Pi Model A+ is The Single Greatest Raspberry Pi Model A+ Case Ever. This enclosure was designed by Mike Doell - just like our elegant, beautiful, and functional Pi Case for Raspberry Pi Model B+ / Pi 2. Made of ultra-durable, super-glossy polycarbonate, it is both good looking and tough enough to toss into your bookbag or toolbox. It has slim openings for all your cables, an easy-to-remove beveled slot for your Micro SD card, slots for both your Pi Camera and upcoming Display, and a space for your GPIO cable to extend out from the Pi. The Pi snaps into the base and the lid fits snugly onto the top. If you want to break out your Pi you can use your case without the lid and add hats to your A+ with ease. This is the basic, classic enclosure with a smoke base and a clear top. More colors are coming soon and we'll have packs to mix and match for ultimate Raspberry Pi A+ enclosure fun, but we'll be starting out with this very neutral gray/clear combo. This case works for the Raspberry Pi Model A+ only. It does not work for the Raspberry Pi Model A, B, B+, or Pi 2. It does work with the model A+ but there will be a bit of empty space of course, and you'll need to snake your USB cable or connector through the front holes which may not work if the cable is bulky No Pi, cables, or Pi Camera included. This product is just the case...
  • Adafruit Photo cell (CdS photoresistor) [ADA161]
    Precio:  $25,459.00
    Expira: 04/01/2022
    Agregar al Carrito   Vista

    Adafruit Photo cell (CdS photoresistor) [ADA161]

    -Titulo Original : Adafruit Photo cell (CdS photoresistor) [ADA161]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 161 // Stock Type: Sensors >> Light/Color/Photo // In Stock & Ready to Ship // CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is about 5-10KΩ, when dark it goes up to 200KΩ.To use, connect one side of the photo cell (either one, its symmetric) to power (for example 5V) and the other side to your microcontroller's analog input pin. Then connect a 10K pull-down resistor from that analog pin to ground. The voltage on the pin will be 2.5V or higher when its light out and near ground when its dark. CdS photocells are not RoHS compliant , so if you need something equivalent but RoHS compiant, check out the photo transistor. For a full tutorial with wiring diagrams, code examples and project ideas, please read the photocell tutorial page ...
  • Adafruit Antennas GPS Antenna 3-5V 28dB 5 meter SMA
    Precio:  $105,229.00
    Agregar al Carrito   Vista

    Adafruit Antennas GPS Antenna 3-5V 28dB 5 meter SMA

    -Titulo Original : Antennas GPS Antenna 3-5V 28dB 5 meter SMA-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 960 // Stock Type: Wireless >> Antennas // In Stock & Ready to Ship // Give your Ultimate GPS V3 a boost with this external active antenna. This GPS antenna draws about 10mA and will give you an additional 28 dB of gain. It's got a 5 meter long cable so it will easily reach wherever you need it to. The antenna is magnetic so it will stick to the top of a car or truck (or any other steel structure) Comes with a standard SMA connector on the end. If you want to connect to our Ultimate GPS V3 module, be sure to pick up a uFL to SMA adapter! GPS not included...
  • Adafruit 4-Channel I2C-Safe Bi-Directional Logic Level Conve
    Precio:  $35,869.00
    Expira: 22/01/2023
    Agregar al Carrito   Vista

    Adafruit 4-Channel I2C-Safe Bi-Directional Logic Level Conve

    -Titulo Original : Adafruit 4-Channel I2C-Safe Bi-Directional Logic Level Converter [ADA757]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 757 // Stock Type: Breakout Boards >> Level Shifters & Expanders // In Stock & Ready to Ship // Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V. We do have some other handy level shifters in the shop, from the DIP 74LVC245 to the fancy bi-directional TXB0108 . However, neither of these are happy to work with I2C, which uses a funky pull-up system to transfer data back and forth. This level shifter board combines the ease-of-use of the bi-directional TXB0108 with an I2C-compatible FET design following NXP's app note. This breakout has 4 BSS138 FETs with 10K pullups. It works down to 1.8V on the low side, and up to 10V on the high side. The 10K's do make the interface a little more sluggish than using a TXB0108 or 74LVC245 so we suggest checking those out if you need high-speed transfer. While we designed it for use with I2C, this works as well for  TTL Serial,  slow...
  • Adafruit 3229 Radio FeatherWing - RFM69HCW 900MHz
    Precio:  $77,039.00
    Agregar al Carrito   Vista

    Adafruit 3229 Radio FeatherWing - RFM69HCW 900MHz

    -Titulo Original : Adafruit (PID 3229 Radio FeatherWing - RFM69HCW 900MHz-Fabricante : Adafruit-Descripcion Original: SX1231 based module with SPI interface // Packet radio with ready-to-go Arduino libraries // Uses the license-free ISM bands // +13 to +20 dBm up to 100 mW Power Output Capability (power output selectable in software) // 50mA (+13 dBm) to 150mA (+20dBm) current draw for transmissions // Add short-hop wireless to your Feather with these Radio Featherwings. These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x's). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. These radio modules come in four variants (two modulation types and two frequencies) The RFM69's are easiest to work with, and are well known and understood. The LoRa radios are exciting, longer-range and more powerful but also more expensive. RFM69 @ 433 MHz - basic packetized FSK/GFSK/MSK/GMSK/OOK radio at 433 MHz for use in Europe ITU 1 license-free ISM, or for amateur use with restrictions (check your local amateur regulations!) RFM69 @ 900 MHz - basic packetized FSK/GFSK/MSK/GMSK/OOK radio at 868 or 915 MHz for use in Americas ITU 2 license-free ISM, or for amateur use with restrictions (check your amateur regulations!) RFM98 @ 433 MHz - LoRa capable radio at 433 MHz for use in Europe ITU 1 license-free ISM, or for amateur use with restrictions (check your local amateur regulations!) RFM95 @ 900 MHz - LoRa capable radio at 868 or 915 MHz for use in Americas ITU 2 license-free ISM, or for amateur use with restrictions (check your local amateur regulations!) This is the RFM69 @ 900 MHz version, it can be used for 868 MHz or 915 MHz (the radios use software configured frequency) These are +20dBm FSK packet radios that have a lot of nice extras in them such as encryption and auto-retransmit. They can go at least 500 meters line of sight using simple wire antennas, probably up to 5Km with directional antennas and settings tweaking...
  • Adafruit 3915 Circuit Playground Express Enclosure
    Precio:  $38,959.00
    Expira: 27/01/2022
    Agregar al Carrito   Vista

    Adafruit 3915 Circuit Playground Express Enclosure

    -Titulo Original : Adafruit 3915 Circuit Playground Express Enclosure-Fabricante : Adafruit-Descripcion Original: This enclosure is only compatible with the Circuit Playground Express! // This minimal but elegant acrylic case will turn your board into an electronic snowflake // The enclosure is designed to snap together securely with no tools required // lic case will turn your board into an electronic snowflake. The enclosure is designed to snap together securely with no tools required. You can still press all the buttons and slide the switch thanks to a clever plastic widget fitted inside // The case winds around all the touch pads so you can still touch them or attach alligator clips // We've got nice cases for many of our beloved boards, but the Circuit Playground Express has been left out of couture enclosure game. Enter Ada-friend Mike Doell to the rescue! This minimal but elegant acrylic case will turn your board into an electronic snowflake. The enclosure is designed to snap together securely with no tools required. You can still press all the buttons and slide the switch thanks to a clever plastic widget fitted inside. The case winds around all the touch pads so you can still touch them or attach alligator clips. On the back, we have two slots that can be used to pass through ribbon or webbing up to 1 /2.5mm wide There is also a slim 1/4-20 nut that is embedded in the center back. This is compatible with any camera mounting accessory, so if you need a solid attachment, you can use any camera positioning tool or tripod. Since it's crystal clear, you can see all the NeoPixels shining in glorious color. The light sensor also works just fine and the case will not block IR messages going in or out. Even though there are no microphone or speaker holes, audio passes through the case via various small openings - we tested it and the difference is barely noticeable. This enclosure is only compatible with the Circuit Playground Express! This case will protect your Circuit Playground Express from every day usage, but it is not waterproof or weatherproof. This product comes as 2 molded plastic halves with the buttons in place. No boards, cables, or accessories are included...
  • Adafruit Thermocouple Amplifier MAX31855 breakout board (MAX
    Precio:  $77,519.00
    Agregar al Carrito   Vista

    Adafruit Thermocouple Amplifier MAX31855 breakout board (MAX

    -Titulo Original : Adafruit Thermocouple Amplifier MAX31855 breakout board (MAX6675 upgrade) [ADA269]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 269 // Stock Type: Sensors >> Temperature // In Stock & Ready to Ship // Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. The MAX31855K does everything for you, and can be easily interfaced with any microcontroller, even one without an analog input. This breakout board has the chip itself, a 3.3V regulator with 10uF bypass capacitors and level shifting circuitry, all assembled and tested. Comes with a 2 pin terminal block (for connecting to the thermocouple) and pin header (to plug into any breadboard or perfboard). Goes great with our 1m K-type thermocouple . If you need a thermocouple interface that can handle other types of thermocouples, check out our 'Universal' MAX31856 amplifier board which can be configured in the Arduino sketch to interface with just about any kind of thermocouple New! Now uses the MAX31855K instead of the MAX6675, so it can measure a wider temperature measurement range. Please note! the MAX31855 is not pin compatible or drop-in code compatible with the MAX6675. We do have an Arduino library for both chips but you'll need to adjust any existing MAX6675 designs for the new MAX31855. The MAX6675 has been discontinued by Maxim.Works with any K type thermocoupleWill not work with any other kind of thermocouple other than K type -200°C to +1350°C output in 0.25 degree increments - note that K thermocouples have about ±2°C to ±6°C accuracyInternal temperature reading3.3 to 5v power supply and logic level compliant!SPI data output requires any 3 digital I/O pins. Hey we even have a handy tutorial on thermocouples which includes an Arduino library, wiring diagrams and example code. How easy is that...
  • Adafruit Circuit Playground Classic
    Precio:  $90,379.00
    Agregar al Carrito   Vista

    Adafruit Circuit Playground Classic

    -Titulo Original : Circuit Playground Classic-Fabricante : ADAFRUIT-Descripcion Original: Circuit Playground, featuring ATMega32U4 is designed to be used with Arduino IDE and code.org CS Discoveries // ATmega32u4 Processor, running at 3.3V and 8MHz. MicroUSB port for programming and debugging with Arduino IDE // The Circuit Playground has USB HID support, so it can act like a mouse or keyboard and attach directly to computers. // Green "ON" LED so you know its powered // Red "#13" LED for basic blinking // Would you like to learn electronics, with an all-in-one board that has sensors and LEDs built in? Circuit Playground is here - and it's the best way to practice programming on real hardware with no soldering or sewing required! This is the Classic version of Circuit Playground, which comes with an ATmega32u4. It's designed to be used with Arduino IDE and code.org CS Discoveries only. It even comes with Firmata already programmed in, so you can use it immediately with code.org Discoveries without any preparation or updates. If you would like to use MakeCode or CircuitPython, check out Circuit Playground Express, which can be used with MakeCode, CircuitPython or Arduino. Circuit Playground features an ATmega32u4 processor (3.3V @ 8MHz), just like our popular Flora. The board's also round and has alligator-clip pads around it so you don't have to solder or sew to make it work. You can power it from USB, a AAA battery pack, or with a Lipoly battery (for advanced users). Just program your code into the board then take it on the go! MicroUSB port for programming and debugging with Arduino IDE USB port can act like serial port, keyboard, mouse, joystick or MIDI Circuit Playground has built-in USB support. Built in USB means you plug it in to program it and it just shows up. All you really need is a Micro-B data/sync USB cable - not included! With the new 1.6.4+ Arduino IDE, it takes only a few seconds to add support. The Circuit Playground has USB HID support, so it can act like a mouse or keyboard and attach directly to computers. Features: 10 x mini NeoPixels, each one can display any color Motion sensor Temperature sensor Light sensor Sound sensor Mini speaker 2 x Push buttons Slide switch 8 x alligator-clip friendly input/output pins I2C, UART, and 4 pins that can do analog inputs/PWM output All 8 pads can act as capacitive touch inputs Reset butto...
Mostrar del 1 al 24 (de 178 productos)
Páginas de Resultados:  1  2  3  4  5 ...  [Siguiente >>] 
Destacados
Revisar todos destacados

Información

Información

Nuestras ofertas

Nuestras ofertas

Su cuenta

Su cuenta

Mantente conectado

Mantente conectado

Contáctenos

Contáctenos

elbazardigital.com   © 2024