Arriba

Inicio » Catalogo » Electrónica, Audio y Video » Componentes Electrónicos > Semiconductores > Circuitos Integrados

Componentes Electrónicos > Semiconductores > Circuitos Integrados

Mostrar: 
Mostrar del 1 al 24 (de 175 productos)
Páginas de Resultados:  1  2  3  4  5 ...  [Siguiente >>] 
  • Adafruit Sewable CR2032 Battery Holder
    Precio:  $46,309.00
    Agregar al Carrito   Vista

    Adafruit Sewable CR2032 Battery Holder

    -Titulo Original : Adafruit Sewable CR2032 Battery Holder-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 653 // Stock Type: Power >> Battery Holders >> Coin Cell // In Stock & Ready to Ship // This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in the metal connection tabs, just large enough for a #5 or smaller needle to pass through. One tab connects to common ground (negative) and the other tab is +3 Volts. This holder is meant to be used with Lithium CR2032 (20mm diameter, 3.2mm thick) sized coin batteries. These are almost always 3V at about 200+ mAh capacity. Lithium coin cells are not rechargeable but they are very easy to find, available at any grocery store. Inserting the coin is easy, the holder is very sturdy, and it snaps out with a push. Its got a nice flat plastic back that you can easily glue in place for extra mechanical stability...
  • Bateria Adafruit Lithium Ion Polymer 3.7v 100mah
    Precio:  $60,249.00
    Agregar al Carrito   Vista

    Bateria Adafruit Lithium Ion Polymer 3.7v 100mah

    -Titulo Original : Battery Packs Lithium Ion Polymer Battery 3.7V 100mAh (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged to 3.7V. This battery has a capacity of ~100mAh for a total of about 0.4 Wh. If you need a larger battery, we have a full range of bigger cells The batteries come pre-attached with a genuine 2-pin JST-PH connector as shown and include the necessary protection circuitry. Because they have a genuine JST connector, not a knock-off, the cable wont snag or get stuck in a matching JST jack, they click in and out smoothly. The included protection circuitry keeps the battery voltage from going too high (over-charging) or low (over-use) which means that the battery will cut-out when completely dead at 3.0V. It will also protect against output shorts. However, even with this protection it is very important that you only use a LiIon/LiPoly constant-voltage/constant-current charger to recharge them and at a rate of 100mA or less. We suggest our Micro Lipo charger, which has a 100mA default rate. Like most lipos, the batteries we sell do not have thermistors built in. This is why we suggest charging at 1 C or even less - 100mA is a good rate, and available from any USB port if using a USB-powered charger Additional safety notes: Do not use a NiMH/NiCad/lead-acid charger! Also, do not abuse these batteries, do not short, bend, crush or puncture. Never charge or use unattended. Always inspect batteries and surrounding circuitry constantly for any damage, loose wiring, or possibility of short circuits. As with all Lithium ion polymer batteries and with any power source - they should be used by experts who are comfortable working with power supplie...
  • Adafruit TCA9548A I2C Multiplexer [ADA2717]
    Precio:  $49,809.00
    Agregar al Carrito   Vista

    Adafruit TCA9548A I2C Multiplexer [ADA2717]

    -Titulo Original : Adafruit TCA9548A I2C Multiplexer [ADA2717]-Fabricante : ADAFRUIT-Descripcion Original: Finally, a way to get up to 8 same-address I2C devices hooked up to one microcontroller - this multiplexer acts as a gatekeeper, shuttling the commands to the selected set of I2C pins with your command. // Using it is fairly straight-forward: the multiplexer itself is on I2C address 0x70 (but can be adjusted from 0x70 to 0x77) and you simply write a single byte with the desired multiplexed output number to that port, and bam - any future I2C packets will get sent to that port. In theory, you could have 8 of these multiplexers on each of 0x70-0x77 addresses in order to control 64 of the same-I2C-addressed-part. // Like all Adafruit breakouts, we put this nice chip on a breakout for you so you can use it on a breadboard with capacitors, and pullups and pulldowns to make usage a snap. Some header is required and once soldered in you can plug it into a solderless-breadboard. The chip itself is 3V and 5V compliant so you can use it with any logic level. // You just found the perfect I2C sensor, and you want to wire up two or three or more of them to your Arduino when you realize Uh oh, this chip has a fixed I2C address, and from what I know about I2C, you cannot have two devices with the same address on the same SDA/SCL pins! Are you out of luck? You would be, if you didn't have this ultra-cool TCA9548A 1-to-8 I2C multiplexer! Finally, a way to get up to 8 same-address I2C devices hooked up to one microcontroller - this multiplexer acts as a gatekeeper, shuttling the commands to the selected set of I2C pins with your command. Using it is fairly straight-forward: the multiplexer itself is on I2C address 0x70 (but can be adjusted from 0x70 to 0x77) and you simply write a single byte with the desired multiplexed output number to that port, and bam - any future I2C packets will get sent to that port. In theory, you could have 8 of these multiplexers on each of 0x70-0x77 addresses in order to control 64 of the same-I2C-addressed-part. Like all Adafruit breakouts, we put this nice chip on a breakout for you so you can use it on a breadboard with capacitors, and pullups and pulldowns to make usage a snap. Some header is required and once soldered in you can plug it into a solderless-breadboard. The chip itself is 3V and 5V compliant so you can use it with any logic level...
  • Adafruit 3988 Prop Maker FeatherWing
    Precio:  $60,609.00
    Agregar al Carrito   Vista

    Adafruit 3988 Prop Maker FeatherWing

    -Titulo Original : Adafruit (3988 Prop Maker FeatherWing-Fabricante : Adafruit-Descripcion Original: The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. Snap-in NeoPixel port - With a 3-pin JST connector, you can plug in one of our JST-wired NeoPixel strips directly, or use a 3-pin JST connector to wire up your favorite shape of addressable NeoPixel LEDs. This port provides high current drive from either the Feather Lipoly or USB port, whichever is higher. A level shifter gives you a clean voltage signal to reduce glitchiness no matter what chip you're using 3W RGB LED drivers - 3 high current MOSFETs will let you connect a 3W RGB LED for powerful eye-blasting glory. For most Feathers, the 3 pins are PWM capable so you can generate any color you like. Available as pin breakouts plus strain-relief holes Triple-Axis Accelerometer with Tap Detection - The LIS3DH is our favorite accelerometer, you can use this for detection motion, tilt or taps. Here's an example of a light saber that makes sounds when swung or hit. We have code for this chip in both Arduino and CircuitPython. Class D Audio Amplifier - Drive a 8Ω 1Watt speaker or 4Ω 3W speaker for sound effects. Plug and play with our cute and slim oval speaker, or connect a picoblade cable for your favorite speaker. For use only with Feathers that have analog audio out such as the Feather M0 Express and M4 series. Low power mode! The power system for the RGB LED, NeoPixels and speaker amplifier can be controlled by a pin to cut power to them, so you have lower power usage when the prop is in sleep or off mode (but can wake up fast by listening to the button press or accelerometer data). When the power pin is set low, the current draw for just the wing is under 1mA and no there's current draw from any attached NeoPixel...
  • Adafruit 3966 BMP388 - Precision Barometric Pressure And Alt
    Precio:  $65,429.00
    Agregar al Carrito   Vista

    Adafruit 3966 BMP388 - Precision Barometric Pressure And Alt

    -Titulo Original : Adafruit BMP388 - Precision Barometric Pressure And Altimeter (3966)-Fabricante : Adafruit-Descripcion Original: Product Dimensions: 21.6mm x 16.6mm x 3.0mm / 0.9" x 0.7" x 0.1" // Product Weight: 1.2g / 0.0oz // Bosch has been a leader in barometric pressure sensors, from the BMP085. BMP180, and BMP280... now we've got the next generation, the Adafruit BMP388 Precision Barometric Pressure sensor. As you would expect, this sensor is similar to its earlier versions but even better. The BMP388 has better precision than ever, which makes it excellent for environmental sensing or as a precision altimeter. It can even be used in either I2C and SPI configurations. The BMP3xx is the next-generation of sensors from Bosch, and is the upgrade to the BMP280 - with a low altitude noise as low as 0.1m and the same fast conversion time. And like the previous BMP280, you can use I2C or SPI. For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI. This sensor has a relative accuracy of 8 Pascals, which translates to about ± 0.5 meter of altitude (compare to the BMP280's 12 Pascal/ ±1 meter). The datasheet sort of implies they intend this sensor to be used for drones and quadcopters, to keep altitude stable, but you could also use this for wearables or any project that wants to track height-above-sea-level. Note that for absolute height you'll still need to enter in the barometric pressure at sea level, if the weather changes, but that's true of every altimeter sensor that uses pressure. You can also measure temperature with ±0.5°C accuracy. Nice sensor right? So we made it easy for you to get right into your next project. The surface-mount sensor is soldered onto a PCB and comes with a 3.3V regulator and level shifting so you can use it with a 3V or 5V logic microcontroller without worry. Check out the Arduino library to get data out in under 10 minutes...
  • Adafruit 8-channel Bi-directional Logic Level Converter [ad
    Precio:  $51,669.00
    Agregar al Carrito   Vista

    Adafruit 8-channel Bi-directional Logic Level Converter [ad

    -Titulo Original : Adafruit 8-Channel Bi-Directional Logic Level Converter [ADA395]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 395 // Stock Type: Breakout Boards >> Level Shifters & Expanders // In Stock & Ready to Ship // Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V. Although one can use resistors to make a divider, for high speed transfers, the resistors can add a lot of slew and cause havoc that is tough to debug. For that reason, we like using 4050/74LVX245 series and similar logic to perform proper level shifting. Only problem is that they are only good in one direction which can be a problem for some specialty bi-diectional interfaces and also makes wiring a little hairy. That's where this lovely chip, the TXB0108 bi-directional level converter comes in! This chip perform bidirectional level shifting from pretty much any voltage to any voltage and will auto-detect the direction . Only thing that doesn't work well with this chip is i2c (because it uses strong pullups which confuse auto-direction sensor). If you need to use pullups, you can but they should be at least 50K ohm - the ones internal to AVRs/Arduino are about 100K ohm so those are OK! Its a little more luxurious than a 74LVX245 but if you just don't want to worry about directional pins this is a life saver! Since this chip is a special bi-directional level shifter it does not have strong output pins that can drive LEDs or long cables, it's meant to sit on a breadboard between two logic chips! If you do not need instant bi-directional support, we suggest the 74LVX245 as below which has strong output drive. This breakout saves you from having to solder the very fine pitch packages that this chip comes with. We also add 0.1uF caps onto both sides and a 10K pull-up resistor on the output enable pin so you can use it right out of the box...
  • Cable lcd For Dell G3 3500 G5 5500 G5 5505 01f2kr 1f2kr
    Precio:  $70,539.00
    Agregar al Carrito   Vista

    Cable lcd For Dell G3 3500 G5 5500 G5 5505 01f2kr 1f2kr

    -Titulo Original : Suyitai LCD LVDS LED EDP 144Hz 40PIN Ribbon Video Screen Video Display Cable Wire Line Replacement For Dell G3 3500 G5 5500 G5 5505 01F2KR 1F2KR 450.0K702.0001-Fabricante : Suyitai-Descripcion Original: - Solo necesita el precio razonable, puede obtener un juego de ajedrez hecho de madera real. Nuestros productos también son respetuosos con el medio ambiente, por lo que no se tiñen con ningún proceso químico y tienen un alto nivel de seguridad. - A y A es actualmente el escaso ajedrez del mercado que cumple con las dimensiones estándar. 15 incrustaciones de tablero con cuadrados de 1,65 (fresno europeo/arce), mientras se equipa con piezas Staunton de 3 king y 1,15 de diámetro de base. (el rey mide el doble de la altura de los cuadrados y el diámetro de la base es el 75 por ciento de los cuadrados). - El uso de piezas premium de triple peso brinda comodidad y tranquilidad al usar la tabla, al mismo tiempo que hace que sea menos probable que se vuelque. La almohadilla de vellón en la parte inferior de la pieza de ajedrez protege la superficie del tablero y mejora la resistencia al deslizamiento. El diseño del cajón mantiene el polvo fuera de las piezas de ajedrez y permite un fácil almacenamiento. - Tanto la practicidad como la estética, nuestro juego de ajedrez, pero también tiene una mano de obra meticulosa y detalles sorprendentes, no solo es una colección, sino también una opción perfecta para regalos navideños...
  • Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]
    Precio:  $100,649.00
    Agregar al Carrito   Vista

    Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]

    -Titulo Original : Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 390 // Stock Type: Power >> Solar >> Chargers // In Stock & Ready to Ship // NOTE: This product is only designed for use with solar panels sold at the Adafruit store. We cannot guarantee this will work with solar panels purchased elsewhere. Please purchase this kit and panels from Adafruit to ensure optimized functionality! A 2.1mm adapter cable is also required to adapt a solar panel to the DC power jack. Make your projects to go green this summer with our specialized USB/Solar Lithium Ion Polymer Battery charger! This charger is a very unique design, perfect for outdoor projects, or DIY iPod chargers. We've spent over a year testing and tinkering with this charger to come up with a plug and play solution to charging batteries with the sun and we're really pleased with what we ended up with. Easy to use! Pick up any of our many 3.7V/4.2V LiIon batteries , and a 6V solar panel . Plug the battery into the BATT port using a 2-pin JST cable and the solar panel into the DC jack using a 2.1mm adapter cable Put the solar panel outside (and keep the battery out of the sun, it needs to be kept cool!) to start charging. You can power another project like a Mintyboost at the same time by connecting to the LOAD output port Our carefully designed charger is designed specifically for solar charging, and will automatically draw the most current possible from the panel in any light condition! Even thought it isn't a 'true' MPPT (max power point tracker), it has near-identical performance without the additional cost of a buck-converter. Our detailed tutorial on how to use this charger includes a design document explaining how it all works. For use with Adafruit Lipoly/LiIon batteries only! Other batteries may have different voltage, chemistry, polarity or pinout. Comes with an assembled charger board, a 2-pin JST cable that will fit into either the BATT or LOAD ports, and a large stabilization capacitor that must be installed in your finished project. Doe...
  • Adafruit 4156 20 Pin 0.1 Female Header - Blue - 5 Pack
    Precio:  $42,329.00
    Agregar al Carrito   Vista

    Adafruit 4156 20 Pin 0.1 Female Header - Blue - 5 Pack

    -Titulo Original : Adafruit 4156 20 Pin 0.1 Female Header - Blue - 5 Pack-Fabricante : Adafruit-Descripcion Original: great for connecting things together, soldering to perf-boards, sockets for wires or break-away header, // Each pack contains five blue 20-pin 0.1" pitch female headers // These are a little extra special in that the plastic holding the pins together is made of blue plastic instead of classic black. // You can cut these down to different sizes fairly easily with diagonal cutters to cut in between pins. // Female header is like the duct tape of electronics. It's great for connecting things together, soldering to perf-boards, sockets for wires or break-away header, etc. We go through these real fast, and thought that given how handy they are, we'd offer them in a pack of five! Each pack contains five blue 20-pin 0.1 pitch female headers. These are a little extra special in that the plastic holding the pins together is made of blue plastic instead of classic black. You can cut these down to different sizes fairly easily with diagonal cutters to cut in between pins...
  • Bateria Lipo 3.7v 200mah 25 X 20 X 6mm Jst Conector
    Precio:  $55,839.00
    Agregar al Carrito   Vista

    Bateria Lipo 3.7v 200mah 25 X 20 X 6mm Jst Conector

    -Titulo Original : 3.7V 200mAh 602025 Lipo battery Rechargeable Lithium Polymer ion Battery Pack with JST Connector-Fabricante : ZONYAKY-Descripcion Original: Voltage: DC 3.7V; Capacity: 200mAh Material: Lithium Polymer; Net Weight: 7g Size: 25 x 20 x 6mm / 0.98 x 0.79 x 0.24 (L*W*T) Connector Type: 2P PH2.0mm Pitch; Cable Length: 5cm / 2 Package Content: 1 x Lithium Polymer Batter...
  • Adafruit AC, DC & Servo Motors Sub-Micro Servo SG51R (1 piec
    Precio:  $66,919.00
    Agregar al Carrito   Vista

    Adafruit AC, DC & Servo Motors Sub-Micro Servo SG51R (1 piec

    -Titulo Original : AC, DC & Servo Motors Sub-Micro Servo SG51R (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2201 // Stock Type: Robotics & CNC >> Robotics // In Stock & Ready to Ship // This is just about the cutest, tiniest little micro servo we could find, even smaller than the 9 gram micro servos we love so much.  It can rotate approximately 180 degrees (90 in each direction) and works just like the standard kind you're used to but  much smaller .   You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in small places. Of course, its not nearly as strong as a standard servo. Works great with the Motor Shield for Arduino or by just wiring up with the Servo library. Comes with a few horns and hardware. To control with an Arduino, we suggest connecting the orange control wire to pin 9 or 10 and using the  Servo library  included with the Arduino IDE ( see here for an example sketch ). Position 0 (1.5ms pulse) is middle, 90 (~2ms pulse) is all the way to the right, -90 (~1ms pulse) is all the way to the left...
  • Adafruit APDS9960 Proximity, Light, RGB, and Gesture Sensor
    Precio:  $55,949.00
    Agregar al Carrito   Vista

    Adafruit APDS9960 Proximity, Light, RGB, and Gesture Sensor

    -Titulo Original : Adafruit APDS9960 Proximity, Light, RGB, and Gesture Sensor-Fabricante : ADAFRUIT-Descripcion Original: This breakout is chock full o' sensors! Add basic gesture sensing, RGB color sensing, proximity sensing, or ambient light sensing to your project with the Adafruit APDS9960 Proximity, Light, RGB and Gesture Sensor. When connected to your microcontroller (running our library code) it can detect simple gestures (left to right, right to left, up to down, down to up are currently supported), return the amount of red, blue, green, and clear light, or return how close an object is to the front of the sensor. This device uses an I2C interface so it's easy to wire up and use. The APDS9960 from Avago Technologies has an integrated IR LED and driver, along with four directional photodiodes that sense reflected IR energy from the LED. It's proximity detection feature allows it to measure the distance an object is from the front of the sensor (up to a few centimeters) with 8 bit resolution...
  • Adafruit 2542 FONA 808 - Mini Cellular GSM GPS Breakout ADA2
    Precio:  $170,859.00
    Expira: 11/01/2022
    Agregar al Carrito   Vista

    Adafruit 2542 FONA 808 - Mini Cellular GSM GPS Breakout ADA2

    -Titulo Original : Adafruit FONA 808 - Mini Cellular GSM GPS Breakout [ADA2542]-Fabricante : Adafruit-Descripcion Original: Includes GPS and GSM antennas // Quad-band 850/900/1800/1900MHz - connect onto any global GSM network with any 2G SIM (in the USA, T-Mobile is suggested) // Fully-integrated GPS (MT3336 chipset) that can be controlled and query over the same serial port // Make and receive voice calls using a headset or an external 32Ω speaker + electret microphone // Send and receive SMS messages, GPRS data (TCP/IP, HTTP, etc) // Cellular + GPS tracking, all in one? Introducing Adafruit FONA 808 MiniGSM + GPS, an all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your project in an tiny package. This module measures only 1.75x1.6 but packs a surprising amount of technology into it's little frame. At the heart is a powerfull GSM cellular module (we use the latest SIM808) with integrated GPS. This module can do just about everything. Onboard LiPoly battery charging circuitry so you can take your project on the go. Use any 500mAh+ LiPoly or LiIon battery and recharge over the MicroUSB when necessary. Two LEDs let you know when its charging and done Standard 4-pole TRRS headphone jack. Use any 'Android' or 'iPhone'-compatible headset with mic Breakouts for external 32Ω speaker and electret mic if you don't want to use a headphone Level shifting circuitry so you can run it with 2.8V to 5V logic. Vibrational motor (buzzer) driver so you can have noiseless notifications uFL connections for external antennas Indicator LEDs for power and network connectivity Standard SIM slides into the back On its own, this module can't do anything. It requires a microcontroller to drive it! We suggest and use an Arduino but any 3-5V microcontroller with a UART can send and receive commands over the RX/TX pins...
  • Adafruit 74LVC245 - Breadboard Friendly 8-bit Logic Level Sh
    Precio:  $30,769.00
    Agregar al Carrito   Vista

    Adafruit 74LVC245 - Breadboard Friendly 8-bit Logic Level Sh

    -Titulo Original : Adafruit 74LVC245 - Breadboard Friendly 8-bit Logic Level Shifter [ADA735]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 735 // Stock Type: Components & Parts >> IC & Transistors // In Stock & Ready to Ship // Most of our customers love using the Arduino for prototyping, design and invention but find themselves stuck when trying to connect the Arduino to the latest sensors, displays, controllers, interfaces, etc. as they are almost all 3.3V logic these days. We try to solve this problem by having all our breakout boards be 5V compatible or when that's not possible, including a level shifter chip but there are still thousands of tempting devices out there. This chip solves the problem of how to interface 3.3V logic devices to a 5.0V logic chip such as the Arduino. Most 3.3V devices do not like being run with 5V signals and can be damaged or flaky. The 74LVC245 is designed so that even when it runs at 1.8V, it still happily accepts 5V signals in one pin and converts it to a lower logic level on the opposite pin. This chip is only for digital signals, it doesn't convert analog signals (you need an op amp for that). It has 8 pipes it can convert but it won't work with bi-directional/pull-up based devices such as I2C or 1-Wire. It does work great for SPI, Serial, Parallel bus, and other logic interfaces. Using it is simple. We suggest checking out the 74LVC245 datasheet for details but essentially: connect VCC to your logic level you want to convert to (say 3.3V), Ground connects to Ground. Wire OE (output enable) to ground to enable the device and DIR (direction) to VCC. Then digital logic on the A pins up to 5V will appear on the B pins shifted down to the VCC logic...
  • Adafruit Mini Metal Speaker w/ Wires - 8 ohm 0.5W [ADA1890]
    Precio:  $30,649.00
    Expira: 17/06/2021
    Agregar al Carrito   Vista

    Adafruit Mini Metal Speaker w/ Wires - 8 ohm 0.5W [ADA1890]

    -Titulo Original : Adafruit Mini Metal Speaker w/ Wires - 8 ohm 0.5W [ADA1890]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1890 // Stock Type: Components & Parts >> Speakers // In Stock & Ready to Ship // Listen up! This tiny 1 diameter speaker cone is the perfect addition to any small audio project where you need an 8 Ω impedance and will be using 0.5W or less of power. We particularly like this cone as it's very simple and its metal body is extremely lightweight. It's very similar to the speaker in the Drawdio kit. Works great with our Wave shield or class D amplifier board . Just be careful not to overdrive it if you're using the class D amp breakouts as it can put 1.7W into the speaker, blowing it out! Start with lower volume and increase carefully...
  • Adafruit FONA - Mini Cellular GSM Breakout - SMA Version [AD
    Precio:  $230,909.00
    Agregar al Carrito   Vista

    Adafruit FONA - Mini Cellular GSM Breakout - SMA Version [AD

    -Titulo Original : Adafruit FONA - Mini Cellular GSM Breakout - SMA Version [ADA1963]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1963 // Stock Type: Wireless >> Cellular // In Stock & Ready to Ship // Ring, Ring! Who's that callin'? It's your breadboard! Introducing Adafruit FONA MiniGSM, an adorable all-in-one cellular phone module that lets you add voice, text, SMS and data to your project in an adorable little package. This module measures only 1.75x1.25 but packs a surprising amount of technology into its little frame. At the heart is a GSM cellular module (we use the latest SIM800) the size of a postage stamp. This module can do just about everything. This version has an SMA connector. For the uFL version, click here! Quad-band 850/900/1800/1900MHz - connect onto any global GSM network with any 2G SIM (in the USA, T-Mobile is suggested)Make and receive voice calls using a headset OR an external 8Ω speaker + electret microphoneSend and receive SMS messagesSend and receive GPRS data (TCP/IP, HTTP, etc.)Scan and receive FM radio broadcasts (yeah, we don't exactly know why this was included but it works really well)PWM/Buzzer vibrational motor controlAT command interface with auto baud detectionSounds delicious, right? So we plated this fine module onto a little breakout with all the extras you need to make your next project shineOnboard LiPoly battery charging circuitry so you can take your project on the go. Use any 500mAh+ LiPoly or LiIon battery and recharge over the MicroUSB when necessary. Two LEDs let you know when its charging and doneStandard 4-pole TRRS headphone jack. Use any 'Android' or 'iPhone'-compatible headset with micBreakouts for external 8Ω speaker and electret mic if you don't want to use a headphoneLevel shifting circuitry so you can run it with 2.8V to 5V logic.Vibrational motor (buzzer) driver so you can have noiseless notificationsSMA connection for external antennaIndicator LEDs for power and network connectivity Standard SIM slides into the bac...
  • Adafruit 2136 2.54mm/0.1 Pitch Terminal Block - 3-pin
    Precio:  $34,299.00
    Expira: 10/08/2023
    Agregar al Carrito   Vista

    Adafruit 2136 2.54mm/0.1 Pitch Terminal Block - 3-pin

    -Titulo Original : Adafruit 2136 2.54mm/0.1 Pitch Terminal Block - 3-pin-Fabricante : Adafruit-Descripcion Original: Dimensions (w/o pins): 9mm x 8mm x 6mm / 0.4" x 0.3" x 0.2" // Pin Length: 3mm / 0.1" // Weight: 0.8g // Wire gauge: 26-20AWG // Distance btwn terminal blocks: 2.5mm // After a long day out harvesting in the terminal block fields, we've returned with a veritable bounty of these very nice and compact 2.54mm/0.1 terminal blocks in a variety of sizes. Our harvest of terminal blocks is great news since nothing makes a project harder to maintain than a lot of loose wiring. That's why we like to use terminal blocks whenever making PCB-to-wire connections. These are 2.54mm spaced blocks so they fit easily into perf or protoboards. They don't fit well into solderless breadboards since the legs are not very long, and they don't snap together or fit side-by-side on a 0.1 grid - but that's okay since we've got a bunch of sizes to choose from. These terminal blocks are also big enough for a range of wire gauges and easy to adjust with a screwdriver. They're not too chunky - so won't take up too much space on your protoboard - and found them pretty ideal for projects where you need a specific number of pins...
  • Adafruit Fast Vibration Sensor Switch (Easy to Trigger) [ADA
    Precio:  $26,509.00
    Expira: 06/05/2023
    Agregar al Carrito   Vista

    Adafruit Fast Vibration Sensor Switch (Easy to Trigger) [ADA

    -Titulo Original : Adafruit Fast Vibration Sensor Switch (Easy to Trigger) [ADA1766]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1766 // Stock Type: Sensors >> Motion // In Stock & Ready to Ship // The poor man's accelerometer/motion sensor! These spring-vibration switches are non-directional vibration induced trigger switches. Inside is a very soft spring coiled around a long metal pin. When the switch is moved, the spring touches the center pole to make contact. So, when there's motion, the two pins will act like a closed switch. When everything is still, the switch is open. Great for basic projects and wearables! We also have a version with a slightly stiffer spring which makes it harder to trigger , and a version with a much more stiff spring which is even harder to trigger ...
  • Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board
    Precio:  $56,269.00
    Agregar al Carrito   Vista

    Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board

    -Titulo Original : Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board-Fabricante : ADAFRUIT-Descripcion Original: TB6612 motor driver // 1.2A per channel // Runs at 2.7V-5V logic. The motor voltage is separate from the logic voltage. Good for motor voltages from 4.5V up to 13.5V // Dimensions: 27mm x 19mm x 3mm / 1.1" x 0.7" x 0.1" // Weight: 1.8g // Spin two DC motors, step one bi-polar or uni-polar stepper, or fire off two solenoids with 1.2A per channel using the TB6612. These are perhaps better known as the drivers in our assembled Adafruit Motorshield or Motor HAT. We really like these dual H-bridges, so if you want to control motors without a shield or HAT these are easy to include on any solderless breadboard or perma-proto. We solder on TB6612 onto a breakout board for you here, with a polarity protection FET on the motor voltage input and a pullup on the standby enable pin. Each breakout chip contains two full H-bridges (four half H-bridges). That means you can drive 2-4 solenoids (only two can be active at a time, on opposite bridges), two DC motors bi-directionally, or one stepper motor. Just make sure they're good for 1.2 Amp or less of current, since that's the limit of this chip. They do handle a peak of 3A but that's just for a short amount of time, like 20 milliseconds. What we like most about this particular driver is that it comes with built in kick-back diodes internally so you dont have to worry about the inductive kick damaging your project or driver! There's two digital inputs per H-bridge (one for each half of the bridge) as well as a PWM input per driver so you can control motor speed. Runs at 2.7V-5V logic. The motor voltage is separate from the logic voltage. Good for motor voltages from 4.5V up to 13.5V! This wont work well for 3V motors. Comes as one assembled and tested breakout plus a small strip of header. You'll need to do some light soldering to attach the header onto the breakout PCB. Arduino, motors, and power supply not included. Check out our handy tutorial on assembly and wiring...
  • Adafruit Stereo Enclosed Speaker Set - 3w 4 Ohm
    Precio:  $60,049.00
    Expira: 23/03/2023
    Agregar al Carrito   Vista

    Adafruit Stereo Enclosed Speaker Set - 3w 4 Ohm

    -Titulo Original : Adafruit Stereo Enclosed Speaker Set - 3W 4 Ohm-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1669 // Stock Type: Components & Parts >> Speakers // In Stock & Ready to Ship // Listen up! This set of two 2.8 x 1.2 speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclosed for good audio volume and quality. The pair have a handy SPK input cable to add audio to your displays (the connectors are similar to the JST-PH series  which is ~2.0mm spacing). We're specifically carrying these to use with our 10.1 inch , 7 inch , or 5.6 inch 1280x800 Display w/ Audio driver boards. However, they work peachy-keen with any of our audio amps as well, such as the MAX98306 , TS2012 or TPA2016 stereo class D amplifiers...
  • Adafruit 3979 ESP32 WROVER-B Module - ESP32 With PSRAM Modul
    Precio:  $78,479.00
    Agregar al Carrito   Vista

    Adafruit 3979 ESP32 WROVER-B Module - ESP32 With PSRAM Modul

    -Titulo Original : Adafruit ESP32 WROVER-B Module - ESP32 With PSRAM Module (3979)-Fabricante : Adafruit-Descripcion Original: Product Dimensions: 31.5mm x 18.0mm x 3.3mm / 1.2" x 0.7" x 0.1" // Product Weight: 2.4g / 0.1oz // The ESP8266 started a small revolution by bringing WiFi to a small and cheap package that also had enough processing power and enough pins to get small things done. Now get ready to take your bite-sized WiFi capabilities to the next level with the ESP-WROVER-32 WiFi / Bluetooth Classic / BLE Module! This modules is even more powerful than the WROOM-32 - it has a 8MB PSRAM chip for when you have massive data buffering needs. It is a bigger module than the WROOM-32. The core processing chip (ESP32) and SPI Flash (4MB) is the same, its just got waaay more RAM available. According to Espressif, the ESP-WROVER-32 is a powerful, generic WiFi-BT-BLE MCU module that targets a wide variety of applications ranging from low-power sensor networks to the most demanding tasks such as voice encoding, music streaming and MP3 decoding. For advanced users only! This product is just the module - which can be difficult to use. You'll need to solder it onto a board with supporting circuitry (See the Espressif's assembled ESP32 development board for a more complete design). This module is for developers at this time, and is FCC, CE, IC, MIC (Telec), KCC, and NCC certified. Please note this product is for people who are comfortable compiling via the Tensilica toolchain. There are the beginnings of an Arduino IDE setup, Lua and MicroPython port. We are providing these for the community of advanced hackers, coders and makers who are willing to help make demos, projects and tutorials for the ESP32...
  • Adafruit 3915 Circuit Playground Express Enclosure
    Precio:  $38,959.00
    Expira: 27/01/2022
    Agregar al Carrito   Vista

    Adafruit 3915 Circuit Playground Express Enclosure

    -Titulo Original : Adafruit 3915 Circuit Playground Express Enclosure-Fabricante : Adafruit-Descripcion Original: This enclosure is only compatible with the Circuit Playground Express! // This minimal but elegant acrylic case will turn your board into an electronic snowflake // The enclosure is designed to snap together securely with no tools required // lic case will turn your board into an electronic snowflake. The enclosure is designed to snap together securely with no tools required. You can still press all the buttons and slide the switch thanks to a clever plastic widget fitted inside // The case winds around all the touch pads so you can still touch them or attach alligator clips // We've got nice cases for many of our beloved boards, but the Circuit Playground Express has been left out of couture enclosure game. Enter Ada-friend Mike Doell to the rescue! This minimal but elegant acrylic case will turn your board into an electronic snowflake. The enclosure is designed to snap together securely with no tools required. You can still press all the buttons and slide the switch thanks to a clever plastic widget fitted inside. The case winds around all the touch pads so you can still touch them or attach alligator clips. On the back, we have two slots that can be used to pass through ribbon or webbing up to 1 /2.5mm wide There is also a slim 1/4-20 nut that is embedded in the center back. This is compatible with any camera mounting accessory, so if you need a solid attachment, you can use any camera positioning tool or tripod. Since it's crystal clear, you can see all the NeoPixels shining in glorious color. The light sensor also works just fine and the case will not block IR messages going in or out. Even though there are no microphone or speaker holes, audio passes through the case via various small openings - we tested it and the difference is barely noticeable. This enclosure is only compatible with the Circuit Playground Express! This case will protect your Circuit Playground Express from every day usage, but it is not waterproof or weatherproof. This product comes as 2 molded plastic halves with the buttons in place. No boards, cables, or accessories are included...
  • Adafruit Flora RGB Smart NeoPixel Version 2 - Pack of 4 [ADA
    Precio:  $66,429.00
    Expira: 10/02/2021
    Agregar al Carrito   Vista

    Adafruit Flora RGB Smart NeoPixel Version 2 - Pack of 4 [ADA

    -Titulo Original : Adafruit Flora RGB Smart NeoPixel Version 2 - Pack of 4 [ADA1260]-Fabricante : ADAFRUIT-Descripcion Original: Flora NeoPixels // Designed specifically for wearables // ultra-bright LED (each pixel can draw as much as 60mA) // High Speed 800KHz communication // Full 24-bit color ability with PWM taken care of by the controller chip // What's a wearable project without LEDs? Our favorite part of the Flora platform is these tiny smart pixels. Designed specifically for wearables, these updated Flora NeoPixels have ultra-cool technology: these ultra-bright LEDs have a constant-current driver cooked right into the LED package! The pixels are chainable - so you only need 1 pin/wire to control as many LEDs as you like. They're easy to sew, and the chainable design means no crossed threads. This is the second version of the Flora NeoPixels, which runs at at 'high speed' 800KHz communication. Unfortunately they are not back-compatible with the chip-on-back 'low speed' (400KHz) Flora NeoPixels. If you have a project that already uses low speed pixels, and you want to attach more pixels to the chain, you will need to purchase version 1's as these are not cross-compatible. These pixels have full 24-bit color ability with PWM taken care of by the controller chip. Since the LED is so bright, you need less current/power to get the effects you want. The driver is constant current so its OK if your battery power changes or fluctuates a little. Each pixel draws as much as 60mA (all three RGB LEDs on for full brightness white). In theory, the Flora can drive up to 500 pixels at 30 FPS (it will run out of RAM after that). However, after about 10 pixels (or if the distance between pixels is more than an inch or two) the resistance of the thread can affect the power supply. For large quantities of pixels over 10, you may want to consider using stranded core wire or copper braid to provide a power bus for the pixels - the current draw will add up fast! Each order comes with 4 individually controllable pixels...
  • Adafruit Bluefruit Le Sniffer - Bluetooth Low Energy (ble 4
    Precio:  $114,469.00
    Expira: 12/12/2021
    Agregar al Carrito   Vista

    Adafruit Bluefruit Le Sniffer - Bluetooth Low Energy (ble 4

    -Titulo Original : Adafruit Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v2.0 [ADA2269]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2269 // Stock Type: Wireless >> Bluetooth // In Stock & Ready to Ship // Interested in learning how Bluetooth Low Energy works down to the packet level? Debugging your own BLE hardware, and trying to spot where something is going wrong? Or maybe you're writing a custom application for your phone or tablet that needs to talk to existing BLE hardware, but you don't know how it works beneath the surface? We have the perfect tool for you!This Bluefruit LE Friend is programmed with a special firmware image that turns it into an easy to use Bluetooth Low Energy sniffer. You can passively capture data exchanges between two BLE devices, pushing the data into Wireshark, the open source network analysis tool, where you can visualize things on a packet level, with useful descriptors to help you make sense of the values without having to crack open the 2000 page Bluetooth 4.0 Core Specification every time.Plug it into your development machine, fire up the special sniffer bridge SW, select the device you want to sniff, and it will fire up Wireshark for you and start pushing data in via a live stream (using Nordic's Windows software), or save to a pcap file that you can analyze with Wireshark later. Please Note :  You can only use this device to listen on Bluetooth Low Energy devices! It will not work on Bluetooth (classic) devices. The Nordic Wireshark-streaming sniffer software is currently Windows only. We have example code using the python API that will work on any OS to log the sniffed data to a pcap file for analysis so you can use this sniffer with any OS with python.The sniffer firmware cannot be used with the the Nordic DFU bootloader firmware, which means that if you want to reprogram this devices you must use a J-Link (and, likely, a SWD adapter + SWD Breakout ) You cannot over-the-air reprogram it. Check out our tutorial for more details and software downloads...
Mostrar del 1 al 24 (de 175 productos)
Páginas de Resultados:  1  2  3  4  5 ...  [Siguiente >>] 
Destacados
Revisar todos destacados

Información

Información

Nuestras ofertas

Nuestras ofertas

Su cuenta

Su cuenta

Mantente conectado

Mantente conectado

Contáctenos

Contáctenos

elbazardigital.com   © 2024