Arriba

Inicio » Catalogo » Electrónica, Audio y Video » Componentes Electrónicos > Semiconductores > Circuitos Integrados

Componentes Electrónicos > Semiconductores > Circuitos Integrados

Mostrar: 
Mostrar del 121 al 144 (de 176 productos)
Páginas de Resultados: [<< Anterior]  ... 6  7  8  [Siguiente >>] 
  • Adafruit 284 FTDI Friend Extras ADA284
    Precio:  $68,789.00
    Agregar al Carrito   Vista

    Adafruit 284 FTDI Friend Extras ADA284

    -Titulo Original : Adafruit FTDI Friend Extras [ADA284]-Fabricante : Adafruit-Descripcion Original: Long gone are the days of parallel ports and serial ports. Now the USB port reigns supreme! But USB is hard, and you just want to transfer your every-day serial data from a microcontroller to computer. What now? Enter the FTDI Friend! The FTDI Friend is a tweaked out FTDI FT232RL chip adapter. Sure, like the well-known FTDI cable, it can provide power to your project and there are 4 signal lines for sending data back and forth. But the Friend can do much more! For example, you can change the signal and power lines to be either 3.3V or 5V. Arduino-derivatives and XBees use the RTS line for programming but what if you need that DTR line? It's there for you. By default, it's setup so that it matches Adafruit's FTDI cables. The 6th pin is RTS (as of Arduino IDE v18 this will work perfectly for uploading to 'inos), the power wire is +5V and the signal levels are 3.3V. You can even rearrange the wire order with a 6-pin extension cable (not included). In a pinch, you can use it to program AVRs (its a bit slow but works!) Item Specifics Length: 38.07mm/1.5in Width: 17.89mm/0.7in Height: 7.7mm/0.31in Weight: 3.4g/0.12o...
  • Adafruit 3316 VL6180X Time Of Flight Distance Ranging Sensor
    Precio:  $63,549.00
    Agregar al Carrito   Vista

    Adafruit 3316 VL6180X Time Of Flight Distance Ranging Sensor

    -Titulo Original : Adafruit (PID 3316 VL6180X Time Of Flight Distance Ranging Sensor (VL6180)-Fabricante : Adafruit-Descripcion Original: VL6180X Time of Flight distance sensor // Range: 5mm to 200mm // On Board 5V regulator and level shifting // Works with 3V to 5V // Works with Arduino and other micro controller projects // The VL6180X (sometimes called the VL6180) is a Time of Flight distance sensor like no other you've used! The sensor contains a very tiny laser source, and a matching sensor. The VL6180X can detect the time of flight, or how long the laser light has taken to bounce back to the sensor. Since it uses a very narrow light source, it is good for determining distance of only the surface directly in front of it. Unlike sonars that bounce ultrasonic waves, the 'cone' of sensing is very narrow. Unlike IR distance sensors that try to measure the amount of light bounced, the VL6180X is much more precise and doesn't have linearity problems or 'double imaging' where you can't tell if an object is very far or very close. This is the 'little sister' of the Adafruit VL53L0X ToF sensor, and can handle about 5mm to 200mm of range distance. It also includes a lux sensor. If you need a larger range, check out the VL53L0X which can measure 50 - 1200 mm. The sensor is small and easy to use in any robotics or interactive project. Since it needs 2.8V power and logic we put the little fellow on a breakout board with a regulator and level shifting. You can use it with any 3-5V power or logic microcontroller with no worries. Each order comes with a small piece of header. Solder the header onto your breakout board with your iron and some solder and wire it up for instant distance-sensing-success! Communicating to the sensor is done over I2C with some simple commands. Most of the work is handled inside the sensor itself, so its very easy to port our Arduino library to another microcontroller...
  • Adafruit RFID Transponder Tools PN532 NFC/RFID Controller Br
    Precio:  $153,629.00
    Agregar al Carrito   Vista

    Adafruit RFID Transponder Tools PN532 NFC/RFID Controller Br

    -Titulo Original : RFID Transponder Tools PN532 NFC/RFID Controller Breakout-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 364 // Stock Type: Wireless >> RFID / NFC // In Stock & Ready to Ship // The PN532 is the most popular NFC chip, and is what is embedded in pretty much every phone or device that does NFC. It can pretty much do it all, such as read and write to tags and cards, communicate with phones (say for payment processing), and 'act' like a NFC tag. If you want to do any sort of embedded NFC work, this is the chip you'll want to use!NFC (Near Field Communications) is a way for two devices very close to each other to communicate. Sort of like a very short range bluetooth that doesn't require authentication. It is an extension of RFID, so anything you can do with RFID you can do with NFC. You can do more stuff with NFC as well, such as communicate bi-directionally with cell phonesBecause it can read and write tags, you can always just use this for RFID-tag projects. We carry a few different tags that work great with this chip. It can also work with any other NFC/RFID Type 1 thru 4 tag.The PN532 is also very flexible, you can use 3.3V TTL UART at any baud rate, I2C or SPI to communicate with it. This chip is also strongly supported by libnfc , simply plug in an FTDI cable and use the FTDI serial port device to communicate - this lets you do NFC dev using any Linux/Mac/Windows computer! We also include onboard power LED, 3.3V regulator and an FTDI header so you can plug in an FTDI friend or FTDI cable and use with libnfc.Comes with: the PN532 breakout board including a tuned 13.56MHz stripline antenna, 0.1 header, 2 jumpers/shunts and a 4050 level shifter chip. We also toss in a  13.56MHz 1K card! ( You can get more tags from us here ...
  • TMPR Sports > Ascend > Honeycomb Polymer Pickleball Pa -RBQC
    Precio:  $481,429.00
    Expira: 30/03/2024
    Agregar al Carrito   Vista

    TMPR Sports > Ascend > Honeycomb Polymer Pickleball Pa -RBQC

    -Titulo Original : TMPR Sports > Ascend > Honeycomb Polymer Pickleball Paddle > Medium Weight > USAPA Approved-Fabricante : TMPR Sports-Descripcion Original: 5.5" handle length // USAPA approved // Aerodynamic and powerful // Great for singles // Medium Weight (7.6 - 7.9 oz.) // The Ascend XT is a medium weight power paddle. It was designed especially for players coming from tennis or racquetball backgrounds who value the aerodynamic shape, making it easier to rapidly move the paddle and add spin to the ball. Players who like to occasionally use a two-handed backhand will appreciate the extra length of the handle. It is also ideal as a singles paddle where power and speed are crucial. The Ascend XT features a honeycomb polymer with graphics printed directly on a fiberglass face...
  • Adafruit 259 , USB Li-Ion/LiPoly Charger, v1.2
    Precio:  $63,289.00
    Agregar al Carrito   Vista

    Adafruit 259 , USB Li-Ion/LiPoly Charger, v1.2

    -Titulo Original : Adafruit 259 , USB Li-Ion/LiPoly Charger, v1.2-Fabricante : ADAFRUIT-Descripcion Original: Comes assembled and tested with a free bonus jst cable // For charging single lithium ion/lithium polymer // Weight: 5.7G ( 0.2Oz) // Chip supports a 10K ntc thermistor which we have stuffed as a plain 10K. For people who require temperature monitors (using high charge rates), remove the 10K and solder in the thermistor in its place // 0.1 inch // This is a lithium ion and lithium polymer battery charger based on the MCP73833. It uses a USB mini-b for connection to any computer or 'USB wall adapter'. charging is done in three stages: first a preconditioning charge, then a constant-current fast charge and finally a constant-voltage trickle charge to keep the battery topped-up. The fast-charge current is 500MA by default, but is easily adjustable from 100MA up to 1000MA by soldering a through-hole resistor on-board. This board is great for DIY projects because it has 3 indicator LEDs - one for power, one for charging status and a third that indicates when charging is complete. You may also keep the battery connected to the charger and pass power through the additional jst connector using the included cable...
  • Adafruit 4028 CircuitPython Starter Kit Itsy Bitsy M4
    Precio:  $109,779.00
    Agregar al Carrito   Vista

    Adafruit 4028 CircuitPython Starter Kit Itsy Bitsy M4

    -Titulo Original : Adafruit (4028 CircuitPython Starter Kit Itsy Bitsy M4-Fabricante : Adafruit-Descripcion Original: You've heard about CircuitPython and maybe you want to get started fast with a breadboard-friendly microcontroller board! We recommend the ItsyBitsy M4 - a super fast chip with tons of GPIO, analog inputs & outputs, with so much RAM that you'll never have to worry about running out of memory. And what better way to get acquainted with ItsyBitsy M4 than with this handy CircuitPython Starter Kit? Small, powerful, with a ultra fast ATSAMD51 Cortex M4 processor running at 120 MHz - this microcontroller board is perfect when you want something very compact, with a ton of horsepower and a bunch of pins. This Itsy is like a bullet train, with it's 120MHz Cortex M4 with floating point support and 512KB Flash and 192KB RAM. Your code will zig and zag and zoom, and with a bunch of extra peripherals for support, this will for sure be your favorite new chipset. We give you a pack of parts for getting started, a lovely Blinka-purple case and even a sticker. Now you've got no excuse for not digging in. Makes for a great workshop pack, hackerspace kit, or gift. Please note the ItsyBitsy M4 is not soldered, some light soldering is required to attach headers to the chip! Once you've got it assembled, tuck it all into the handy carrying case. Includes: 1 x Adafruit ItsyBitsy M4 Express come with loose headers (not shown in the photo but they're in there) 1 x Maker-Friendly Zipper Case in Royal Purple 1 x Half-Size Breadboard 1 x USB Cable - 6 A/microB 1 x Premium Male/Male Jumper Wires set Starter Pack Component Bag 1x Breadboard-friendly SPDT Slide Switch 1x Diffused RGB (tri-color) LED 1x Piezo Buzzer 1x Photo cell light sensor 3x 12mm Tactile Switches 1x Diffused 10mm Red LED 1x Diffused 10mm Green LED 1x 10K Trim Potentiometer 5x 10K 5% 1/4W resistors 5x 560 ohm 5% 1/4W resistor...
  • Adafruit USB Mini-B Breakout Board [ADA1764]
    Precio:  $24,509.00
    Agregar al Carrito   Vista

    Adafruit USB Mini-B Breakout Board [ADA1764]

    -Titulo Original : Adafruit USB Mini-B Breakout Board [ADA1764]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1764 // Stock Type: Breakout Boards >> Batteries/Power // In Stock & Ready to Ship // Simple but effective - this breakout board has a USB Mini-B connector, with all 5 pins broken out. Great for pairing with a microcontroller with USB support, or adding USB 5V power to a project. Comes with one fully assembled and tested mini B breakout PCB and a small stick of 0.1 header so you can solder it on and plug into a breadboard...
  • Adafruit Super-bright 5mm Ir Led (25 Pack) [ada388]
    Precio:  $45,329.00
    Expira: 28/08/2023
    Agregar al Carrito   Vista

    Adafruit Super-bright 5mm Ir Led (25 Pack) [ada388]

    -Titulo Original : Adafruit Super-bright 5mm IR LED (25 pack) [ADA388]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 388 // Stock Type: LEDs >> Bare LEDs // In Stock & Ready to Ship // Infrared LEDs are used for remote controls (they're the little LED in the part you point at your TV) and 'night-vision' cameras, and these little blue guys are high powered ones! They are 940nm wavelength, which is what nearly all devices listen to. They're 20 degree beamwidth, and work great for any kind of remote control application. We used one of these to make a camera control footswitch/intervalometer. These are the same LEDs we use in our super TV-B-Gone kit. You can drive them continuously (for 'night vision' illumination) with 100mA and for IR remote application they can take up to 1 Amp pulses (!). For high powered use, we suggest matching these up with our power MOSFETs . If you want to make a sender/receiver pair, you'll want to get an IR remote receiver sensor as well. We have a tutorial that covers everything you'll need to know about IR remote control sensing as well as how to 'clone' a remote contro...
  • Adafruit NeoTrellis RGB Driver PCB for 4x4 Keypad (3954)
    Precio:  $61,849.00
    Expira: 04/04/2021
    Agregar al Carrito   Vista

    Adafruit NeoTrellis RGB Driver PCB for 4x4 Keypad (3954)

    -Titulo Original : Adafruit NeoTrellis RGB Driver PCB for 4x4 Keypad (3954)-Fabricante : ADAFRUIT-Descripcion Original: 4x4 button pad boards // Each order comes with one NeoTrellis board with seesaw chip and 16 NeoPixels already soldered in place // Elastomer button pad not included // By popular request, we've upgraded our popular Trellis elastomer button kits to now have a PCB with full color NeoPixel support! You heard that right, no more single-color LEDs, you can now have any color you like under the fantastic rubbery button pads we sell. These 4x4 button pad boards are fully tile-able and communicate over I2C. With 5 address pins, you've got the ability to connect up to 32 together in any arrangement you like. With our trusty seesaw I2C-to-anything chip, you don't even need to manage the NeoPixel driving. That's right! Both the button management and LED driving is completely handled for you all over plain I2C. With both Arduino/C++ and CircuitPython/Python library support, you can use these pads with any and all microcontroller or computer boards. Perfect for your next cool interface, MIDI instrument, control panel...whatever could benefit from beautiful diffused colorful buttons. For fast connection to a single board, we include a JST-PH 4-pin connector that will give you power+data access. It's Grove compatible (the cable fits, even though its not the exact same connector), or you can use a JST-PH 4 pin cable. You can tile up to 32 boards together by soldering them edge-to-edge and soldering closed the I2C address jumpers, then use one I2C connection for all tiled NeoTrellis boards! Each order comes with one NeoTrellis board with seesaw chip and 16 NeoPixels already soldered in place. Elastomer button pad not included, so be sure to pick one up...
  • Adafruit 2821 Feather HUZZAH With ESP8266 WiFi ADA2821
    Precio:  $93,809.00
    Agregar al Carrito   Vista

    Adafruit 2821 Feather HUZZAH With ESP8266 WiFi ADA2821

    -Titulo Original : Adafruit Feather HUZZAH With ESP8266 WiFi [ADA2821]-Fabricante : Adafruit-Descripcion Original: Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather HUZZAH ESP8266 - our take on an 'all-in-one' ESP8266 WiFi development board with built in USB and battery charging. Its an ESP8266 WiFi module with all the extras you need, ready to rock! Measures 2.0 x 0.9 x 0.28 (51mm x 23mm x 8mm) without headers soldered in Light as a (large?) feather - 9.7 grams ESP8266 @ 80MHz with 3.3V logic/power 4MB of FLASH (32 MBit) Built in WiFi 802.11 b/g/n 3.3V regulator with 500mA peak current output CP2104 USB-Serial converter onboard with 921600 max baudrate for speedy uploading Auto-reset support for getting into bootload mode before firmware upload 9 x GPIO pins - can also be used as I2C and SPI 1 x analog inputs 1.0V max Built in 100mA LiPoly charger with charging status indicator LED, can also cut a trace to disable the charger Pin #0 red LED for general purpose blinking. Pin #2 blue LED for bootloading debug & general purpose blinking Power/enable pin 4 mounting holes Reset butto...
  • Adafruit Pigrrl 2.0 Custom Gamepad Pcb [ada3015]
    Precio:  $54,259.00
    Agregar al Carrito   Vista

    Adafruit Pigrrl 2.0 Custom Gamepad Pcb [ada3015]

    -Titulo Original : Adafruit PiGRRL 2.0 Custom Gamepad PCB [ADA3015]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 3015 // Stock Type: Kits & Projects >> Project packs // In Stock & Ready to Ship // This is the Custom Gamepad PCB for the PiGRRL 2 pack ! The board is designed for use in portable gaming projects like the PiGRRL 2 but it's basically everything-you-need to make your very own DIY gaming project with GPIO inputWe've dramatically cut the build time in half of the PiGRRL 2 pack by making this custom gamepad PCB. Just solder in 6mm tactile switch buttons and an 2x20 header or IDC box header to the gamepad PCB - No more tedious button wiring! Comes with just the PCB! Best for people who already have the rest of the parts, or are doing a custom build. Check out the PiGrrl2 tutorial guide for schematics, details, files, and mor...
  • Adafruit Passive Gps Antenna Ufl - 9mm X 9mm -2dbi Gain
    Precio:  $30,279.00
    Agregar al Carrito   Vista

    Adafruit Passive Gps Antenna Ufl - 9mm X 9mm -2dbi Gain

    -Titulo Original : Passive Gps Antenna Ufl - 9mm X 9mm -2dbi Gain-Fabricante : ADAFRUIT-Descripcion Original: Wow that's a tiny GPS antenna! This passive antenna is only 9mm x 9mm x 6.5mm in size, with a 50mm long uFL cable. Great for when you want to keep things small. Comes with a standard uFL connector on the end. Perfect for our FONA 808! Not good for our Ultimate GPS breakouts/shields/hat as those are designed for active antennas. This is the 9mm versio...
  • Adafruit Pro Trinket Liion/lipoly Backpack Add-on
    Precio:  $38,899.00
    Agregar al Carrito   Vista

    Adafruit Pro Trinket Liion/lipoly Backpack Add-on

    -Titulo Original : Adafruit Pro Trinket LiIon/LiPoly Backpack Add-On-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2124 // Stock Type: Power >> LiIon & LiPoly >> Accessories // In Stock & Ready to Ship // If you have a Pro Trinket you probably know it's the perfect little size for a portable project. This LiPoly backpack makes it really easy to do! Instead of wiring 2 or 3 boards together to make a charging system, this little PCB sits on top of the Pro Trinket and allows a LiPoly/LiIon battery to plug in. When the Pro Trinket USB port is powered, the battery is recharged automatically. Unplug the USB port and the Pro Trinket will switch over to the rechargeable battery.Ideally, this backpack is for use with the 3.3V Pro Trinket, so that the battery voltage (3.7V-4.2V) will get regulated down to 3.3V on the Pro Trinket board. However, many times, you can run a 5V Pro Trinket + accessories off of the ~4V from the LiPoly battery with no problem. (Technically its overclocking but we've never seen that affect the Pro Trinket itself, AVRs are happy to overclock without complaint).Solder the backpack on with the extra long header so that it can still plug into a breadboard, or clip the long header leads short afterwards for a slim package. There are two LEDs - one red and one green. While charging, the red LED is lit. When the battery is fully charged and ready for use, the green LED turns on. Seriously, it could not get more easy.If you want to add an On/Off switch, we also made that really easy. The two 0.1 holes with a box around them are the battery output line. Carefully cut the trace between them with a hobby knife and replace with two wires from a switch like this slide switch , or this pushbutton one , for example. Charging is performed in three stages: first a preconditioning charge, then a constant-current fast charge and finally a constant-voltage trickle charge to keep the battery topped-up. The charge current is 100mA by default, so it will work with any size battery and USB port. If you want you can easily change it over to 500mA mode by soldering closed the jumper on the bottom, for when you'l...
  • Adafruit 4031 Vertical Breadboard Friendly 3.5mm Mono Headph
    Precio:  $23,609.00
    Agregar al Carrito   Vista

    Adafruit 4031 Vertical Breadboard Friendly 3.5mm Mono Headph

    -Titulo Original : Adafruit [4031 Vertical Breadboard Friendly 3.5mm Mono Headphone Jack-Fabricante : Adafruit-Descripcion Original: Dimensions: 18 x 13.5 x 9mm // Product Weight: 1.0g / 0.0oz // Adafruit Part # 4031 // Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jack is inserted. You can use any 3.5mm audio cable with this jack. The pins are on 0.1 spacing so it plugs very solidly (and vertically!) into a breadboard, perma-proto or perf-board. Works best if soldered into a perf-board but does work in a solder-less one Each order comes with one headphone jack. Breadboard and audio cable not included...
  • Adafruit Magnetic contact switch (door sensor) [ADA375]
    Precio:  $41,709.00
    Agregar al Carrito   Vista

    Adafruit Magnetic contact switch (door sensor) [ADA375]

    -Titulo Original : Adafruit Magnetic contact switch (door sensor) [ADA375]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 375 // Stock Type: Sensors >> Proximity // In Stock & Ready to Ship // This sensor is essentially a reed switch, encased in an ABS plastic shell. Normally the reed is 'open' (no connection between the two wires). The other half is a magnet. When the magnet is less than 13mm (0.5) away, the reed switch closes. They're often used to detect when a door or drawer is open, which is why they have mounting tabs and screws. You can also pick up some double-sided foam tape from a hardware store to mount these, that works well without needing screws...
  • Adafruit Feather M4 Express - Featuring ATSAMD51 - ATSAMD51
    Precio:  $104,399.00
    Agregar al Carrito   Vista

    Adafruit Feather M4 Express - Featuring ATSAMD51 - ATSAMD51

    -Titulo Original : Adafruit Feather M4 Express - Featuring ATSAMD51 - ATSAMD51 Cortex M4-Fabricante : ADAFRUIT-Descripcion Original: 512KB Flash and 192KB RAM // ATSAMD51J19 // 120MHz Cortex M4 // It's what you've been waiting for, the Feather M4 Express featuring ATSAMD51. This Feather is fast like a swift, smart like an owl, strong like a ox-bird (it's half ox, half bird, OK?) This feather is powered by our new favorite chip, the ATSAMD51J19 - with its 120MHz Cortex M4 with floating point support and 512KB Flash and 192KB RAM. Your code will zig and zag and zoom, and with a bunch of extra peripherals for support, this will for sure be your favorite new chipset. And best of all, it's a Feather - so you know it will work with all our FeatherWings! What a great way to quickly get up and running. The most exciting part of the Feather M4 is that while you can use it with the Arduino IDE - and it's bonkers fast when you do, we are shipping it with CircuitPython on board. When you plug it in, it will show up as a very small disk drive with main.py on it. Edit main.py with your favorite text editor to build your project using Python, the most popular programming language. No installs, IDE or compiler needed, so you can use it on any computer, even ChromeBooks or computers you can't install software on. When you're done, unplug the Feather and your code will go with you. The Feather M4 Express uses the extra space left over to add a Mini NeoPixel, 2 MB SPI Flash storage and a little prototyping space. You can use the SPI Flash storage like a very tiny hard drive. When used in CircuitPython, the 2 MB flash acts as storage for all your scripts, libraries and files. When used in Arduino, you can read/write files to it, like a little datalogger or SD card, and then with our helper program, access the files over USB...
  • Adafruit Audio Ic Development Tools Mono 2.5w Class D Audio
    Precio:  $34,269.00
    Agregar al Carrito   Vista

    Adafruit Audio Ic Development Tools Mono 2.5w Class D Audio

    -Titulo Original : Audio IC Development Tools Adafruit Mono 2.5W Class D Audio Amplifier - PAM8302 (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2130 // Stock Type: Breakout Boards >> Amplifiers/Sound // In Stock & Ready to Ship // This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Î speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic LM386 amps! The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin  to ground. The output is Bridge Tied - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Output Power: 2.5W at 4Î, 10% THD, 1.5W at 8Î, 10% THD, with 5.5V Supply50dB PSRR at 1KHzFilterless design, with ferrite bead + capacitors on output.Fixed 24dB gain, onboard trim potentiometer for adjusting input volume.Thermal and short-circuit/over-current protectionLow current draw: 4mA quiescent and 1uA in shutdown mod...
  • Adafruit 3988 Prop Maker FeatherWing
    Precio:  $54,549.00
    Agregar al Carrito   Vista

    Adafruit 3988 Prop Maker FeatherWing

    -Titulo Original : Adafruit (3988 Prop Maker FeatherWing-Fabricante : Adafruit-Descripcion Original: The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. Snap-in NeoPixel port - With a 3-pin JST connector, you can plug in one of our JST-wired NeoPixel strips directly, or use a 3-pin JST connector to wire up your favorite shape of addressable NeoPixel LEDs. This port provides high current drive from either the Feather Lipoly or USB port, whichever is higher. A level shifter gives you a clean voltage signal to reduce glitchiness no matter what chip you're using 3W RGB LED drivers - 3 high current MOSFETs will let you connect a 3W RGB LED for powerful eye-blasting glory. For most Feathers, the 3 pins are PWM capable so you can generate any color you like. Available as pin breakouts plus strain-relief holes Triple-Axis Accelerometer with Tap Detection - The LIS3DH is our favorite accelerometer, you can use this for detection motion, tilt or taps. Here's an example of a light saber that makes sounds when swung or hit. We have code for this chip in both Arduino and CircuitPython. Class D Audio Amplifier - Drive a 8Ω 1Watt speaker or 4Ω 3W speaker for sound effects. Plug and play with our cute and slim oval speaker, or connect a picoblade cable for your favorite speaker. For use only with Feathers that have analog audio out such as the Feather M0 Express and M4 series. Low power mode! The power system for the RGB LED, NeoPixels and speaker amplifier can be controlled by a pin to cut power to them, so you have lower power usage when the prop is in sleep or off mode (but can wake up fast by listening to the button press or accelerometer data). When the power pin is set low, the current draw for just the wing is under 1mA and no there's current draw from any attached NeoPixel...
  • Adafruit 3966 BMP388 - Precision Barometric Pressure And Alt
    Precio:  $58,879.00
    Agregar al Carrito   Vista

    Adafruit 3966 BMP388 - Precision Barometric Pressure And Alt

    -Titulo Original : Adafruit BMP388 - Precision Barometric Pressure And Altimeter (3966)-Fabricante : Adafruit-Descripcion Original: Product Dimensions: 21.6mm x 16.6mm x 3.0mm / 0.9" x 0.7" x 0.1" // Product Weight: 1.2g / 0.0oz // Bosch has been a leader in barometric pressure sensors, from the BMP085. BMP180, and BMP280... now we've got the next generation, the Adafruit BMP388 Precision Barometric Pressure sensor. As you would expect, this sensor is similar to its earlier versions but even better. The BMP388 has better precision than ever, which makes it excellent for environmental sensing or as a precision altimeter. It can even be used in either I2C and SPI configurations. The BMP3xx is the next-generation of sensors from Bosch, and is the upgrade to the BMP280 - with a low altitude noise as low as 0.1m and the same fast conversion time. And like the previous BMP280, you can use I2C or SPI. For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI. This sensor has a relative accuracy of 8 Pascals, which translates to about ± 0.5 meter of altitude (compare to the BMP280's 12 Pascal/ ±1 meter). The datasheet sort of implies they intend this sensor to be used for drones and quadcopters, to keep altitude stable, but you could also use this for wearables or any project that wants to track height-above-sea-level. Note that for absolute height you'll still need to enter in the barometric pressure at sea level, if the weather changes, but that's true of every altimeter sensor that uses pressure. You can also measure temperature with ±0.5°C accuracy. Nice sensor right? So we made it easy for you to get right into your next project. The surface-mount sensor is soldered onto a PCB and comes with a 3.3V regulator and level shifting so you can use it with a 3V or 5V logic microcontroller without worry. Check out the Arduino library to get data out in under 10 minutes...
  • Adafruit Round Force-Sensitive Resistor (FSR) - Interlink 40
    Precio:  $33,619.00
    Expira: 12/10/2021
    Agregar al Carrito   Vista

    Adafruit Round Force-Sensitive Resistor (FSR) - Interlink 40

    -Titulo Original : Adafruit Round Force-Sensitive Resistor (FSR) - Interlink 402 [ADA166]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 166 // Stock Type: Sensors >> Touch // In Stock & Ready to Ship // FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This sensor is a Interlink model 402 FSR with 1/2 diameter sensing region.FSR's are basically a resistor that changes its resistive value (in ohms Ω) depending on how much its pressed. These sensors are fairly low cost, and easy to use but they're rarely accurate. They also vary some from sensor to sensor perhaps 10%. So basically when you use FSR's you should only expect to get ranges of response. While FSRs can detect weight, they're a bad choice for detecting exactly how many pounds of weight are on them.FSRs are made of plastic and the connection tab is crimped on delicate material. The best way to connect to these is to simply plug them into a breadboard or use a clamp-style connector like alligator clips, female header, or a terminal block. It is possible to solder onto the tabs but you must be very fast because if your iron is not good quality or you dally even a few seconds, you will melt the plastic and ruin the FSR! For a full tutorial with wiring diagrams, code examples and project ideas, please read the FSR tutorial page ...
  • Cable lcd For Dell G3 3500 G5 5500 G5 5505 01f2kr 1f2kr
    Precio:  $63,479.00
    Agregar al Carrito   Vista

    Cable lcd For Dell G3 3500 G5 5500 G5 5505 01f2kr 1f2kr

    -Titulo Original : Suyitai LCD LVDS LED EDP 144Hz 40PIN Ribbon Video Screen Video Display Cable Wire Line Replacement For Dell G3 3500 G5 5500 G5 5505 01F2KR 1F2KR 450.0K702.0001-Fabricante : Suyitai-Descripcion Original: - Solo necesita el precio razonable, puede obtener un juego de ajedrez hecho de madera real. Nuestros productos también son respetuosos con el medio ambiente, por lo que no se tiñen con ningún proceso químico y tienen un alto nivel de seguridad. - A y A es actualmente el escaso ajedrez del mercado que cumple con las dimensiones estándar. 15 incrustaciones de tablero con cuadrados de 1,65 (fresno europeo/arce), mientras se equipa con piezas Staunton de 3 king y 1,15 de diámetro de base. (el rey mide el doble de la altura de los cuadrados y el diámetro de la base es el 75 por ciento de los cuadrados). - El uso de piezas premium de triple peso brinda comodidad y tranquilidad al usar la tabla, al mismo tiempo que hace que sea menos probable que se vuelque. La almohadilla de vellón en la parte inferior de la pieza de ajedrez protege la superficie del tablero y mejora la resistencia al deslizamiento. El diseño del cajón mantiene el polvo fuera de las piezas de ajedrez y permite un fácil almacenamiento. - Tanto la practicidad como la estética, nuestro juego de ajedrez, pero también tiene una mano de obra meticulosa y detalles sorprendentes, no solo es una colección, sino también una opción perfecta para regalos navideños...
  • Adafruit Bluefruit LE UART Friend - Bluetooth Low Energy (BL
    Precio:  $73,489.00
    Agregar al Carrito   Vista

    Adafruit Bluefruit LE UART Friend - Bluetooth Low Energy (BL

    -Titulo Original : Adafruit Bluefruit LE UART Friend - Bluetooth Low Energy (BLE)-Fabricante : ADAFRUIT-Descripcion Original: Add bluetooth support to your project easily using this easy to use module from Adafruit // Download the free iOS and Android App by Adafruit to get started quickly // High quality module with custom firmware written by Adafruit. Having issues? This product is fully supported by Adafruit! // Full control over the device // Would you like to add powerful and easy-to-use Bluetooth Low Energy to your robot, art or other electronics project? Heck yeah! With BLE now included in modern smart phones and tablets, its fun to add wireless connectivity. So what you really need is the new Adafruit Bluefruit LE UART Friend! The Bluefruit LE UART Friend makes it easy to add Bluetooth Low Energy connectivity to anything with a hardware or software serial port. We even have nice hardware flow control so you won't have to think about losing data. Connect to your Arduino or other microcontroller or even just a standard FTDI cable for debugging and testing. This multi-function module can do quite a lot! For most people, they'll be very happy to use the standard Nordic UART RX/TX connection profile. In this profile, the Bluefruit acts as a data pipe, that can 'transparently' transmit back and forth from your iOS or Android device. You can use our iOS App or Android App, or write your own to communicate with the UART service. Download Adafruit's free Android/iOS app and you're ready to rock...
  • Adafruit 4156 20 Pin 0.1 Female Header - Blue - 5 Pack
    Precio:  $38,099.00
    Agregar al Carrito   Vista

    Adafruit 4156 20 Pin 0.1 Female Header - Blue - 5 Pack

    -Titulo Original : Adafruit 4156 20 Pin 0.1 Female Header - Blue - 5 Pack-Fabricante : Adafruit-Descripcion Original: great for connecting things together, soldering to perf-boards, sockets for wires or break-away header, // Each pack contains five blue 20-pin 0.1" pitch female headers // These are a little extra special in that the plastic holding the pins together is made of blue plastic instead of classic black. // You can cut these down to different sizes fairly easily with diagonal cutters to cut in between pins. // Female header is like the duct tape of electronics. It's great for connecting things together, soldering to perf-boards, sockets for wires or break-away header, etc. We go through these real fast, and thought that given how handy they are, we'd offer them in a pack of five! Each pack contains five blue 20-pin 0.1 pitch female headers. These are a little extra special in that the plastic holding the pins together is made of blue plastic instead of classic black. You can cut these down to different sizes fairly easily with diagonal cutters to cut in between pins...
  • Bateria Lipo 3.7v 200mah 25 X 20 X 6mm Jst Conector
    Precio:  $50,259.00
    Agregar al Carrito   Vista

    Bateria Lipo 3.7v 200mah 25 X 20 X 6mm Jst Conector

    -Titulo Original : 3.7V 200mAh 602025 Lipo battery Rechargeable Lithium Polymer ion Battery Pack with JST Connector-Fabricante : ZONYAKY-Descripcion Original: Voltage: DC 3.7V; Capacity: 200mAh Material: Lithium Polymer; Net Weight: 7g Size: 25 x 20 x 6mm / 0.98 x 0.79 x 0.24 (L*W*T) Connector Type: 2P PH2.0mm Pitch; Cable Length: 5cm / 2 Package Content: 1 x Lithium Polymer Batter...
Mostrar del 121 al 144 (de 176 productos)
Páginas de Resultados: [<< Anterior]  ... 6  7  8  [Siguiente >>] 
Destacados
Revisar todos destacados

Información

Información

Nuestras ofertas

Nuestras ofertas

Su cuenta

Su cuenta

Mantente conectado

Mantente conectado

Contáctenos

Contáctenos

elbazardigital.com   © 2024