-Titulo Original : Adafruit 4258 LPS35HW Water Resistant Pressure Sensor-Fabricante : Adafruit-Descripcion Original: water resistant barometric pressure and temperature sensor that is also safe to use in wet environments // should work well for normal wet situations like weather stations or high humidity // 260 to 1260 hPa absolute pressure range // 24-bit pressure data output -- ODR from 1 Hz to 75 H // 16-bit temperature data output -- SPI and I²C interfaces // Sometimes you need to sense pressure in a damp environment. And sometimes you need to know the relative changes in pressure as well as the absolute pressure. For the times you need to do both (or either), the LPS35HW is the pressure sensor for you. Combining protection from water intrusion with support for high precision relative and absolute measurements, this sensor will do what you need. With drivers for CircuitPython, Arduino, and Raspberry Pi, and support for I2C or SPI (Arduino only SPI support, for now) you'll be measuring pressure in moist situations in no time. The ST LPS35HW is a water resistant barometric pressure and temperature sensor that is also safe to use in wet environments. The sensing element is nestled safely in a ceramic package and is encased in a waterproof gel that prevents water that gets into the sensor from interfering with readings. It does not carry any ratings for resistance to moisture so you probably don't want to take it to the bottom of the Mariana Trench, but it should work well for normal wet situations like weather stations or high humidity. Along with not being afraid of getting wet, the LPS35HW has a 24bit pressure data and 16 bit temperature data, allowing it to deliver pressure readings with +/- 0.1% hPa accuracy. It can measure from 260 to 1260 hPa and is able to withstand pressure up to 20 times its measurement range. To help you take measurements to your requirements, the LPS35HW also offers an adjustable data rate, as well as a low pass filter to remove noise from the signal. Finally, the onboard temperature compensation makes sure that your readings are always good and won't vary as the temperature changes. We placed this sensor on a breakout board with a 3.3V regulator and level shifting circuitry so it can be used by 3V or 5V power/logic devices. A small piece of header is also included, so you can solder it in for use with a breadboard...

-Titulo Original : Adafruit 1335 Peltier Thermoelectric Cooler Module With Heat Sink Assembly, 12 Volt, 5 Amp-Fabricante : Adafruit-Descripcion Original: Keep the heat down with a peltier module. These unique electronic coolers can generate a temperature differential when powered. Put simply, apply 12V 5a power supply to the red (positive) and black (negative) wires and one side will get frosty cold while the other side gets hot. For best results, you'll need to wick away that heat (otherwise the cold side will slowly get warmer). a fan and/or heat sink is ideal. The unit comes fully assembled with the peltier module, heat sink and fan. This is a 12V module, and is rated for up to 72 Watts max (up to 14V/6a) but when used with a regulated 12V output, they don't draw much more than 5 Amps, so we suggest our 12V/5a power adapter for use. (You will need to cut the connector and expose the wires or use a power jack to screw terminal adapter.). Max current: 6a at 12V. Suggested voltage range: 12V to 15.5V. Maximum temperature differential (tmax at QC = 0): 66°c. Maximum cooling power (QC max.) at 15.3V: 97W. 127 peltier elements. DC resistance: 2.5 ohms. Silicone seal. Peltier module: 1.6 inch x 1.6 inch x 0.13 inch (40 x 40 x 3.5 mm). aluminum plate: 1.6 inch x 2.4 inch (40 x 60 mm). heat sink: 3.5 inch x 3.5 inch (90 x 90 mm)...

-Titulo Original : Adafruit Accessories Waterproof 3xAA Battery Holder (1 Piece)-Fabricante : Adafruit-Descripcion Original: Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches together with 4 machine screws. What we like about this design is that the hexnuts are captive in one side and you can assemble/disassemble as many times as you need. There's a potted power switch and a rubber-boot on-off switch (press to turn on/off). Use with any alkaline or rechargeable batteries for about 4.5V output. Would work great with our waterproof DC power plugs (just use heatshrink to waterproof the solder connections) The power cable wires are not polarity marked, use any multimeter to verify the polarity during use. We also have a 2xAA version when you need a smaller & lighter bo...

-Titulo Original : Adafruit 2258 Enclosure For Raspberry Pi 2 & Pi 3 Model B-Fabricante : Adafruit-Descripcion Original: Lid thickness: 0.2 inch // Not superior, cables, or superior camera included // Case dimensions (without lid): 3.7" x 2.5" x 1.0" // Made in China // Also compatible with the superior 1 b+. this enclosure is made of ultra-durable, super-glossy polycarbonate and is both good looking and tough enough to toss into your Backpack or toolbox. It has slim openings for all your cables, an easy-to-remove beveled slot for your Micro SD card, openings for both your superior camera and the much anticipated display. It also has a space for your gpio cable to extend out from the superior we've also added it to our Raspberry superior 2 starter bundle. The superior board snaps into the base and the lid fits nicely onto the top. If you want to break out your superior, you can use your case without the lid and easily add hats to your b+. this is a basic enclosure with a smoke base and a clear top. This case works for the Raspberry superior 2258 b+ and superior 2/superior 3 2258 b only. It does not work for the Raspberry superior 2258 a or b. It can work with the 2258 a+, but there will be a bit of empty space of course, and you'll need to snake your USB cable or connector through the front holes which may not work If the cable is bulky...

-Titulo Original : Adafruit 2 X 2032 Coin Cell Battery Holder - 6V Output With On/Off Switch [ADA783]-Fabricante : Adafruit-Descripcion Original: 2 x 2032 Coin Cell Battery Holder - 6V output with On/Off switch [ADA783...

-Titulo Original : Adafruit Wired Miniature Electret Microphone [ADA1935]-Fabricante : Adafruit-Descripcion Original: That's one tiny microphone! At about the size of a mature aphid, this wired Electret Microphone is perfect for your FONA. This microphone's very similar to our PCB-mount Elecret Microphone but is significantly smaller and has pre-attached 65mm long wires. We don't have a specific datasheet for it but it can be biased with 2V and 2K impedence. You do need an electret microphone amplifier to boost the millivolt-signal up to line level. The FONA has this amplifier part built into it but something like an Arduino does not. We tested it with the FONA and it works great for voice purposes, you may also be able to use it with our other microphone amplifiers (like #1713 and #1063) and if you desolder the onboard microphones...

-Titulo Original : Adafruit Panel Mount Extension USB Cable - Micro B Male To Micro B Female [ADA3258]-Fabricante : Adafruit-Descripcion Original: Interested in making neat stuff with an Arduino-compatible board but not sure where to start? This kit includes all the pieces needed to complete over 20 different circuit and projects. Basically everything you need to be playing within minutes of its arrival. No soldering required, works with Mac, Windows and Linux! This item is the same exact kit as https://www.adafruit.com/product/170 This pack includes the Adafruit Metro. METRO is the culmination of years of playing with AVRs: we wanted to make a development board that is easy to use and is hacker friendly. At the heart is an ATmega328P, with 32KB of flash and 2KB of RAM, running at 16 MHz. It is fully compatible with the Arduino IDE (select Arduino UNO in the board-type menu) Power the METRO with 7-9V polarity protected DC or the micro USB connector to any 5V USB source. The 2.1mm DC jack has an on/off switch next to it so you can turn off your setup easily. The METRO will automagically switch between USB and DC. METRO has 19 GPIO pins, 6 of which are Analog in as well, and 2 of which are reserved for the USB-serial converter. There's also 6 PWMs available on 3 timers (1 x 16-bit, 2 x 8-bit). There's a hardware SPI port, hardware I2C port and hardware UART to USB. Logic level is 5V but by cutting and soldering closed a jumper, you can easily convert it to 3.3V logic USB to Serial converter, there's a hardware USB to Serial converter that can be used by any computer to listen/send data to the METRO, and can also be used to launch and update code via the bootloader Four indicator LEDs, on the front edge of the PCB, for easy debugging. One green power LED, two RX/TX LEDs for the UART, and a red LED connected to pin PB5 Easy reprogramming, comes pre-loaded with the Optiboot bootloader, which is supported by avrdude and only uses 512 bytes. Fully compatible with the Arduino IDE (select Arduino UNO in the board-type menu) Works with all Adafruit shields...

-Titulo Original : Adafruit (PID 1946 FONA - Mini Cellular GSM Breakout UFL Version-Fabricante : Adafruit-Descripcion Original: Send and receive SMS messages // Send and receive GRPS data (TCP/IP, HTTP, etc) // Scan and receive FM radio broadcasts // NOT INCLUDED: Microcontroller, external antenna, SIM card, other components to complete your project // Soldering is required // Introducing Adafruit FONA MiniGSM, an adorable all-in-one cellular phone module that lets you add voice, text, SMS and data to your project in an adorable little package. This module measures only 1.75x1.25. At the heart is a GSM cellular module (we use the latest SIM800). This module can do just about everything. This version has a uFL connector. Quad-band 850/900/1800/1900MHz - connect onto any global GSM network with any 2G SIM (in the USA, T-Mobile is suggested) Make and receive voice calls using a headset OR an external 8Ω speaker + electret microphone Send and receive SMS messages Send and receive GPRS data (TCP/IP, HTTP, etc.) Scan and receive FM radio broadcasts (yeah, we don't exactly know why this was included but it works really well) PWM/Buzzer vibrational motor control AT command interface with auto baud detection Sounds delicious, right? So we plated this fine module onto a little breakout with all the extras you need to make your next project shine: Onboard LiPoly battery charging circuitry so you can take your project on the go. Use any 500mAh+ LiPoly or LiIon battery and recharge over the MicroUSB when necessary. Two LEDs let you know when its charging and done Standard 4-pole TRRS headphone jack. Use any 'Android' or 'iPhone'-compatible headset with mic Breakouts for external 8Ω speaker and electret mic if you don't want to use a headphone Level shifting circuitry so you can run it with 2.8V to 5V logic. Vibrational motor (buzzer) driver so you can have noiseless notifications uFL connections for external antenna Indicator LEDs for power and network connectivity Standard SIM slides into the back On its own, this module can't do anything. It requires a microcontroller to drive it! We suggest and use an Arduino but any 3-5V microcontroller with a UART can send and receive commands over the RX/TX pins...

-Titulo Original : ADAFRUIT INDUSTRIES 85 SHIELD STACKING HEADERS ARDUINO (R3 COMPATIBLE) (1 Piece)-Fabricante : Adafruit-Descripcion Original: Our set includes 1x 10-pin header, 2x 8-pin headers, 2x 6-pin headers, and one 2x3 header. // The legs are all 10.5mm long, so after PCB thickness (1.7mm) you have a height of 8.8mm - just enough to clear the Arduino's USB-B connector // Theyre also fully compatible with shields designed for Arduino R3 and the Leonardo // shields that dont use the 10-pin header or 2x3 header, use the 6 or 8 pin ones. // What are they for? Stacking. You put the headers on top of your Arduino and then you can add shields like our Protoshield or our Motor Shield or our Proto-Screwshield (pictured above) to get your Arduino doing all the cool things you want it to. Our set includes 1x 10-pin header, 2x 8-pin headers, 2x 6-pin headers, and one 2x3 header. The legs are all 10.5mm long, so after PCB thickness (1.7mm) you have a height of 8.8mm - just enough to clear the Arduino's USB-B connector. Theyre also fully compatible with shields designed for Arduino R3 and the Leonardo. For shields that dont use the 10-pin header or 2x3 header, use the 6 or 8 pin ones...

-Titulo Original : Adafruit (3988 Prop Maker FeatherWing-Fabricante : Adafruit-Descripcion Original: The Adafruit Feather series gives you lots of options for a small, portable, rechargeable microcontroller board. Perfect for fitting into your next prop build! This FeatherWing will unlock the prop-maker inside all of us, with tons of stuff packed in to make sabers & swords, props, toys, cosplay pieces, and more. Snap-in NeoPixel port - With a 3-pin JST connector, you can plug in one of our JST-wired NeoPixel strips directly, or use a 3-pin JST connector to wire up your favorite shape of addressable NeoPixel LEDs. This port provides high current drive from either the Feather Lipoly or USB port, whichever is higher. A level shifter gives you a clean voltage signal to reduce glitchiness no matter what chip you're using 3W RGB LED drivers - 3 high current MOSFETs will let you connect a 3W RGB LED for powerful eye-blasting glory. For most Feathers, the 3 pins are PWM capable so you can generate any color you like. Available as pin breakouts plus strain-relief holes Triple-Axis Accelerometer with Tap Detection - The LIS3DH is our favorite accelerometer, you can use this for detection motion, tilt or taps. Here's an example of a light saber that makes sounds when swung or hit. We have code for this chip in both Arduino and CircuitPython. Class D Audio Amplifier - Drive a 8Ω 1Watt speaker or 4Ω 3W speaker for sound effects. Plug and play with our cute and slim oval speaker, or connect a picoblade cable for your favorite speaker. For use only with Feathers that have analog audio out such as the Feather M0 Express and M4 series. Low power mode! The power system for the RGB LED, NeoPixels and speaker amplifier can be controlled by a pin to cut power to them, so you have lower power usage when the prop is in sleep or off mode (but can wake up fast by listening to the button press or accelerometer data). When the power pin is set low, the current draw for just the wing is under 1mA and no there's current draw from any attached NeoPixel...

-Titulo Original : Adafruit Membrane 3x4 Matrix Keypad Extras [ADA419]-Fabricante : Adafruit-Descripcion Original: Punch in your secret key into this numeric matrix keypad. This keypad has 12 buttons, arranged in a telephone-line 3x4 grid. It's made of a thin, flexible membrane material with an adhesive backing (just remove the paper) so you can attach it to nearly anything. The keys are connected into a matrix, so you only need 7 microcontroller pins (3-columns and 4-rows) to scan through the pad. Check the tutorials tab for links to an Arduino library and example code...

-Titulo Original : Adafruit Membrane 1x4 Keypad Extras [ADA1332]-Fabricante : Adafruit-Descripcion Original: Easy to use keypad for your Arduino or Raspberry Pi project // This keypad has 4 buttons, and since every key has its own wire line, no matrix code is required // The membrane is soft and has a removable paper backing to expose a strong adhesive // Includes a 5-pin extra-long header strip so you can plug this into a breadboard with ease. // Keypad dimensions: 69.14mm / 2.72" x 20.07mm / 0.79" // Punch in your secret key into this numeric membrane keypad. This keypad has 4 buttons, and since every key has its own wire line, no matrix code is required - just treat these like every day switches. The membrane is soft and has a removable paper backing to expose a strong adhesive so you can stick this on an enclosure and feed the cable through a slot. Its a simple keypad but that's why we like it. We include a 5-pin extra-long header strip so you can plug this into a breadboard with ease. Technical Details Weight: 2.83g Keypad dimensions: 69.14mm / 2.72 x 20.07mm / 0.79 Length of cable + connector: 87.31mm / 3.43 x 14.28mm / 0.56 5-pin 0.1 pitch connecto...

-Titulo Original : Adafruit A/V And RCA (Composite Video, Audio) Cable For Raspberry Pi [ADA2881]-Fabricante : Adafruit-Descripcion Original: Description this a/v rca cable for raspberry pi is a great way to turn your pi 3, 2, a+ or b+'s output into a fullposite video and audio device. Simply connect the cable to your raspberry pi's 3. 5mm jack and the other side into whatever device you're looking to connect to and get full rca visuals and sound. We're big fans of rca connectors. They're one of our favorite plugs that everyone has a fond memory of using. Yellow'sposite video while red and white are for stereo audio. The cable is around 5 feet long. This cable has the right wiring so you canposite video out - e. G. The trrs corresponds to left, right, ground, video...

-Titulo Original : Adafruit (PID 3229 Radio FeatherWing - RFM69HCW 900MHz-Fabricante : Adafruit-Descripcion Original: SX1231 based module with SPI interface // Packet radio with ready-to-go Arduino libraries // Uses the license-free ISM bands // +13 to +20 dBm up to 100 mW Power Output Capability (power output selectable in software) // 50mA (+13 dBm) to 150mA (+20dBm) current draw for transmissions // Add short-hop wireless to your Feather with these Radio Featherwings. These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x's). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. These radio modules come in four variants (two modulation types and two frequencies) The RFM69's are easiest to work with, and are well known and understood. The LoRa radios are exciting, longer-range and more powerful but also more expensive. RFM69 @ 433 MHz - basic packetized FSK/GFSK/MSK/GMSK/OOK radio at 433 MHz for use in Europe ITU 1 license-free ISM, or for amateur use with restrictions (check your local amateur regulations!) RFM69 @ 900 MHz - basic packetized FSK/GFSK/MSK/GMSK/OOK radio at 868 or 915 MHz for use in Americas ITU 2 license-free ISM, or for amateur use with restrictions (check your amateur regulations!) RFM98 @ 433 MHz - LoRa capable radio at 433 MHz for use in Europe ITU 1 license-free ISM, or for amateur use with restrictions (check your local amateur regulations!) RFM95 @ 900 MHz - LoRa capable radio at 868 or 915 MHz for use in Americas ITU 2 license-free ISM, or for amateur use with restrictions (check your local amateur regulations!) This is the RFM69 @ 900 MHz version, it can be used for 868 MHz or 915 MHz (the radios use software configured frequency) These are +20dBm FSK packet radios that have a lot of nice extras in them such as encryption and auto-retransmit. They can go at least 500 meters line of sight using simple wire antennas, probably up to 5Km with directional antennas and settings tweaking...

-Titulo Original : Adafruit (3942 HC-SR04 Ultrasonic Sonar Distance Sensor 2 X 10K Resistors-Fabricante : Adafruit-Descripcion Original: Power and Logic Voltage: DC 5V // Current during measurment: 15mA // Ultrasonic Frequency: 40 KHz // Measuring Angle: 15º // Trigger Input Signal: 10uS high pulse // If you're like me, you've dreamed of being a dolphin - smoothly gliding through the water. Using your echo-location abilities to detect tasty fish treats. Until genetic modifications catches up with our desires, we'll just have to make do with these handy HC-SR04 Ultrasonic Sonar Distance Sensors and a pair of flippers. These ubiquitous sensors are really common in robotics projects, but they can also be used for automation, interactive art and motion sensing. They work at about 2cm to 400cm away, but we think 10cm-250cm will get you the best results. These sensors are fast, fairly easy to use, and low cost. They do require powering from 5V for best results: connect GND (ground) and VCC to 5V power. While the Trig signal can be 3V or 5V, the 'return' Echo signal is 5V logic. For that reason, we include two 10K resistors, use these as a divider to convert the 5V logic level to a safe 2.5V that you can ready with your 3V device...

-Titulo Original : Adafruit EL Wire Coin Cell Mini Inverter [ADA1350]-Fabricante : Adafruit-Descripcion Original: A really tiny portable inverter for EL wire. Powers off of a single CR2032 coin battery (not included!), it can drive up to 50cm / 20 inches of our high-brightness EL wire or 10cm x 1cm long piece of EL tape for 3 hours (or longer if the EL wire is less than 50cm long). There is a button for selecting steady/blink/off modes. Comes with a 2.5mm pitch female JST connector. Like all inverters we've used, the 2000 Hz oscillation is slightly audible...

-Titulo Original : Adafruit Accessories Breadboard-Friendly 3.5mm Stereo Headphone Jack (1 Piece)-Fabricante : Adafruit-Descripcion Original: Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. // It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. // ou can use any 3.5mm stereo cable with this jack. The pins are on 0.1" spacing so it plugs very solidly into a breadboard, perma-proto or perf-board. // Each order comes with one headphone jack, breadboard and audio cable not included! // Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a stereo jack with disconnect-switches on Left and Right channels as well as a center ground pin. You can use any 3.5mm stereo cable with this jack. The pins are on 0.1 spacing so it plugs very solidly into a breadboard, perma-proto or perf-board. Each order comes with one headphone jack, breadboard and audio cable not included...

-Titulo Original : Adafruit [4031 Vertical Breadboard Friendly 3.5mm Mono Headphone Jack-Fabricante : Adafruit-Descripcion Original: Dimensions: 18 x 13.5 x 9mm // Product Weight: 1.0g / 0.0oz // Adafruit Part # 4031 // Pipe audio in or out of your project with this very handy breadboard-friendly audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left tip pin and a pin that will be disconnected when a jack is inserted. You can use any 3.5mm audio cable with this jack. The pins are on 0.1 spacing so it plugs very solidly (and vertically!) into a breadboard, perma-proto or perf-board. Works best if soldered into a perf-board but does work in a solder-less one Each order comes with one headphone jack. Breadboard and audio cable not included...

-Titulo Original : Adafruit 4208 JST SH 4-pin Right Angle Connector (10-Pack) - Qwiic Compatible-Fabricante : Adafruit-Descripcion Original: 3.3VDC Power - Red wire on cables // Ground - Black wire on cables // I2C SDA Data - Blue wire on cables // I2C SCL Clock - Yellow wire on cables // If you're a DIY enthusiast who likes to micro-manage your project's connections, here is a 10-pack of some micro JST SH connectors! They're solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place. This connector can be used with Qwiic boards and cables, to easily connect sensors and drivers from one board to the other. Match them up with the cables if you want to maintain compatibility (The cables are made symmetrically so don't worry about which side goes where!) When used with Qwiic the pins are: 3.3VDC Power - Red wire on cables Ground - Black wire on cables I2C SDA Data - Blue wire on cables I2C SCL Clock - Yellow wire on cable...

-Titulo Original : Adafruit 2359 Raspberry Pi A Case - Smoke Base W/Clear Top-Fabricante : Adafruit-Descripcion Original: Case Dimensions (without lid): 73mm x 63mm x 26mm / 2.9" x 2.5" x 1" // Lid Thickness: 4mm / 0.2" // 39g // It took awhile to perfect - but that's okay since we can now safely say that the Adafruit case for Raspberry Pi Model A+ is The Single Greatest Raspberry Pi Model A+ Case Ever. This enclosure was designed by Mike Doell - just like our elegant, beautiful, and functional Pi Case for Raspberry Pi Model B+ / Pi 2. Made of ultra-durable, super-glossy polycarbonate, it is both good looking and tough enough to toss into your bookbag or toolbox. It has slim openings for all your cables, an easy-to-remove beveled slot for your Micro SD card, slots for both your Pi Camera and upcoming Display, and a space for your GPIO cable to extend out from the Pi. The Pi snaps into the base and the lid fits snugly onto the top. If you want to break out your Pi you can use your case without the lid and add hats to your A+ with ease. This is the basic, classic enclosure with a smoke base and a clear top. More colors are coming soon and we'll have packs to mix and match for ultimate Raspberry Pi A+ enclosure fun, but we'll be starting out with this very neutral gray/clear combo. This case works for the Raspberry Pi Model A+ only. It does not work for the Raspberry Pi Model A, B, B+, or Pi 2. It does work with the model A+ but there will be a bit of empty space of course, and you'll need to snake your USB cable or connector through the front holes which may not work if the cable is bulky No Pi, cables, or Pi Camera included. This product is just the case...

-Titulo Original : Adafruit 9-DOF Absolute Orientation IMU Fusion Breakout - BNO055-Fabricante : Adafruit-Descripcion Original: Este paquete de 4 bujías DENSO es compatible con Toyota Corolla 2015, 2014, 2013, 2012, 2011, 2010, 2009 1.8L L4 y es perfecto para una puesta a punto o una mejora del rendimiento. REDUCE LAS EMISIONES Y LAS FALLAS DE ENCENDIDO: la bujía patentada DENSO permite la ignición completa del combustible en la cámara de combustión. Prácticamente elimina los arranques erráticos causados ??por mezclas de combustible deficientes y suciedad excesiva. La bujía DENSO emplea un electrodo de tierra único diseñado para generar un núcleo de chispa más grande en el punto de ignición. Una mayor energía de chispa significa un mejor recorrido de la llama, lo que produce una combustión más completa, consistente y eficiente OBTENGA MAYOR EFICIENCIA DE COMBUSTIBLE: esta bujía DENSO enciende mezclas más pobres que las bujías convencionales y mejora la respuesta del acelerador. Su electrodo de tierra fue desarrollado para mejorar la inflamabilidad para aumentar la eficiencia en la purificación de gases de emisión y el consumo de combustible. La bujía DENSO está 100 % precalentada para garantizar un funcionamiento confiable y dura el doble que las bujías convencionales. El exclusivo aislador de cinco costillas reduce el flashover y disminuye la pérdida de voltaje CONFÍE EN PIEZAS AUTOMÁTICAS DE CALIDAD: desde el desarrollo de bobinas de encendido directo hasta la revolución del concepto de bujía de rendimiento del mercado de accesorios mediante el uso de platino e iridio, DENSO a menudo está en la primera línea del avance del producto. CONFÍA EN DENSO: La industria automotriz ha reconocido el compromiso de DENSO con la calidad a través de premios tan prestigiosos como el Premio Deming a la Calidad, el Premio del Presidente de J.D. Power and Associates y numerosos premios a proveedores por calidad...

-Titulo Original : Adafruit 4226 INA260 High Or Low Side Voltage, Current, Power Sensor-Fabricante : Adafruit-Descripcion Original: - Funciona muy bien con cualquier microcontrolador que sea compatible con CircuitPython o Arduino, así como con computadoras de placa única como Raspberry Pi. - Compatible con lógica de 3V o 5V y puede medir voltajes de bus hasta +36VDC. No apto para uso con voltajes de CA. - Resistencia de derivación de precisión integrada que se puede usar para medir hasta +36 V hasta 15 A continuos en el lado alto o bajo - Hace el trabajo de dos multímetros Esta placa de conexión bien puede ser la última solución de detección de corriente que necesite comprar. No solo puede hacer el trabajo de dos multímetros, sino que puede hacerlo con una precisión y flexibilidad asombrosas. Con él, puede medir la corriente CC del lado alto o bajo, el voltaje del bus y hacer que calcule automáticamente la potencia. Puede hacerlo en rangos impresionantes de voltaje, corriente y temperatura con una precisión superior al 1%, todo mientras entrega los datos en un formato fácil de usar sobre I2C. Funciona muy bien con cualquier microcontrolador que sea compatible con CircuitPython o Arduino, así como con computadoras de placa única como Raspberry Pi. Es compatible con lógica de 3V o 5V y puede medir voltajes de bus hasta +36VDC. No apto para uso con voltajes de CA. La mayoría de los dispositivos de medición de corriente funcionan con algunas restricciones notables que limitan para qué se pueden usar. Muchos son solo de lado bajo, lo que puede causar problemas a medida que la referencia a tierra cambia con la corriente. Otros, como su hermano pequeño, el INA219B, evitan esto al medir en el lado alto, pero necesitan cambiar su resistencia de derivación para medir diferentes rangos de corriente. El INA260 evita estas limitaciones y, con su resistencia de derivación de precisión integrada, se puede usar para medir hasta +36 V hasta 15 A continuos en el lado alto o bajo. ¡Guau! El voltaje a través de la resistencia de derivación integrada de 2 miliohmios (0,002 ohmios), 0,1% se mide mediante el ADC interno de 16 bits, lo que permite mediciones en el impresionante rango de corriente con una resolución de 1,5 mA. (¡La resistencia de la resistencia es tan baja que algunos multímetros la registrarán como un cortocircuito!) En una configuración de lado alto, la medición del voltaje del bus y el cálculo de potencia se pueden recuperar con precisión, sin embargo, los piratas informáticos avanzados que desean medir el voltaje del bus en una configuración de lado bajo necesitará cortar el puente que conecta V+ a VBUS y conectar el pin VBUS al bus de voltaje...

-Titulo Original : Adafruit Accessories 3xAAA Battery Holder W/ On/Off Switch (1 Piece)-Fabricante : Adafruit-Descripcion Original: Interruptor encendido / apagado - Úselo con cualquier batería alcalina o recargable para una salida de aproximadamente 4.5V - Conecta 3 pilas AAA - Ideal para proyectos de 3.3...

-Titulo Original : Ada Adafruit (pid 4366) Tlv493d Triple-axis Magnetometer - Stemma Qt/qwiic-Fabricante : Adafruit-Descripcion Original: - Salida digital a través de una interfaz estándar I2C basada en 2 cileres de hasta 1 mbit/seg - Resolución de datos de 12 bits para cada dirección de medición - BX, por y BZ Medición de campo lineal hasta +130 TM - Excelente coincidencia de medición x/y para una detección de ángulo precisa El magnetómetro TLV493D de 3 ejes es un pequeño sensor excelente para detectar imanes en 3D. De hecho, ¡el fabricante Infineon sugiere que podría usarse para hacer un joystick! También podría usarlo para otras cosas geniales como detectar objetos con imanes conectados, como la tapa de una caja, o tal vez una estatua que desbloquea su guarida secreta cuando se coloca en su manto. El TLD493D sobresale al medir los campos magnéticos cercanos en tres dimensiones. No va a hacer una buena brújula, no es lo suficientemente sensible como para recoger el campo magnético de la Tierra, pero puede usarlo para rastrear el movimiento de los imanes cercanos en tres dimensiones. Aquí hay algunas especificaciones: salida digital a través de una interfaz estándar I2C estándar de 2 hilos de hasta 1 mbit/seg. Medición para una detección de ángulo precisa Como no estamos para hacer, hemos hecho que el TLV sea fácil de usar colocándolo en una PCB ruptura junto con los circuitos para soportarlo. Un regulador de voltaje y un cambio de nivel lógico se combinan para que se pueda usar con una gama de microcontroladores con niveles lógicos de 3.3V o 5V. Incluso le damos un PIN para que use el exceso de jugo de 3.3V que no necesita el TLV493D. También hemos equipado el breakout con los conectores QT de Stemma STEMMA QWIIC Sparkfun para permitirle usarlo con otras placas equipadas de manera similar sin necesidad de soldar. Debido a que el TLV493D habla I2C, solo necesita dos cables (además de potencia) para interactuar con su microcontrolador, y puede compartir esos pines con otros sensores I2C. El fabricante Infineon tuvo la amabilidad de proporcionar una biblioteca para usar el sensor con Arduino, y hemos escrito uno para usarlo con CircuitPython y Python para su uso en Raspberry Pi y otras computadoras Linu...