-Titulo Original : Adafruit USB Mini-B Breakout Board [ADA1764]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1764 // Stock Type: Breakout Boards >> Batteries/Power // In Stock & Ready to Ship // Simple but effective - this breakout board has a USB Mini-B connector, with all 5 pins broken out. Great for pairing with a microcontroller with USB support, or adding USB 5V power to a project. Comes with one fully assembled and tested mini B breakout PCB and a small stick of 0.1 header so you can solder it on and plug into a breadboard...

-Titulo Original : Adafruit (3428 Reset/Enable Controller - KA75330 3.3V Voltage Detector-Fabricante : ADAFRUIT-Descripcion Original: Product Dimensions: 19.0mm x 4.6mm x 3.5mm / 0.7" x 0.2" x 0.1" // Product Weight: 0.2g / 0.0oz // A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Eventually the battery runs down, and goes below 3.3V, so the voltage to the ESP8266 core is too low, and could cause a lockup or corrupted data. Or maybe your battery is already drained and you're trying to charge it back up, but as you are trying to charge it up, the Huzzah turns on and the spike of current drains the battery immediately so it never gets through the trickle-charging stage. This little chip is a simple solution: It monitors the voltage on one Input pin, and when that voltage goes below 3.3V, it will pull the Output pin low. If you connect that Output pin to the Enable pin on the Feather, it will make sure that the Huzzah does not run if the battery dips too low. The KA75330 starts running at voltages as low as 0.8V so it'll be the first thing in your circuit that starts up. This little helper can really ease power start-up issues! Works best with microcontrollers and boards that have an Enable pin that is normally pulled high to enable function, and pulled to ground to disable...

-Titulo Original : Adafruit Conductive Fiber - Stainless Steel 20um - 10 grams [ADA1088]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1088 // Stock Type: Wearables >> Materials >> Other // In Stock & Ready to Ship // This conductive fiber is super interesting! It's great for felting and could also be spun into yarn if that's your thing. We tested many different fiber thicknesses for needle felting and found that this one (20um fiber thickness) is the most pleasurable to work with. Use about 0.2g of the stuff to make a felt touch button suitable for use with the MaKey MaKey or capacitive touch sensing circuit. Make felt controllers or felt buttons onto an existing wool sweater!  You can also make a squeeze/pressure sensor with this fiber, as it becomes less resistive the more you squeeze the fibers together. Make sure to combine this fiber with a natural animal fiber (which have scales) for best results. We think 10g is the perfect amount and will get you through several projects. MaKey MaKey and alligator clips not included...

-Titulo Original : Adafruit Slim Sticker-type GSM/Cellular Quad-Band Antenna - 3dBi uFL [ADA1991]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1991 // Stock Type: Wireless >> Antennas // In Stock & Ready to Ship // That's one slim cellular antenna! At just 75mm long from tip to tip and and with a thickness of just 2mm, this 3dBi GSM antenna is slim, compact and sensitive, with a 3dBi gain.  The antenna juts out from its base with stick-on back so you attach it to an enclosure if you're making something like, say, a DIY phone.  It has a tiny uFL connector on the end - which is perfect for the  FONA - but will also work well for any other RF project on the 850/900/1800/1900/2100 bands, such as any other Cellular or GSM/GPRS device.We also offer a version of this antenna with a longer 300mm cable ...

-Titulo Original : Adafruit Pro Trinket 5V 16MHz (1 Piece)-Fabricante : Adafruit -Descripcion Original: Chip integrado ATmega328P en paquete QFN Velocidad de reloj de 16MHz, FLASH de 28K disponible El cargador de arranque USB con un buen indicador LED se parece a un USBtinyISP para que pueda programarlo con AVRdude y / o Arduino IDE (con algunas modificaciones simples de configuración). También tiene encabezados para un puerto FTDI para reprogramación Conector micro-USB para alimentación y / o carga USB, puede colocarlo en una caja o pegarlo con cinta adhesiva y usar cualquier cable USB para cuando desee reprogramar. Regulador de potencia incorporado de 5.0V con capacidad de salida de 150mA y caída ultra baja. Entrada de hasta 16 V, protección de polaridad inversa, protección térmica y de límite de corriente. Trinket tiene una hermana mayor en la ciudad: ¡Pro Trinket 5V! Pro Trinket combina todo lo que te gusta de Trinket con la familiaridad del chip Arduino de núcleo común, el ATmega328. Es como un Arduino Pro Mini con más pines y USB, tan delicioso. Trinket ya tiene un año, y aunque ha sido genial ver toneladas de pequeños proyectos, a veces solo necesitas más pines, más FLASH y más RAM. Es por eso que diseñamos Pro Trinket, con 18 GPIO, 2 entradas analógicas adicionales, 28K de flash y 2K de RAM. Al igual que el Trinket, tiene soporte de carga de arranque USB integrado: esta vez optamos por un conector MicroUSB. También agregamos el soporte Optiboot, para que pueda programar su Pro Trinket a través de USB o con un cable FTDI al igual que el Pro Mini y sus amigos. El Pro Trinket PCB mide solo 1.5 x 0.7 x 0.2 (sin encabezados) pero tiene casi la misma capacidad que un Arduino UNO. Por lo tanto, es excelente una vez que haya terminado un prototipo en un Arduino UNO oficial y quiera hacer el proyecto es más pequeño. El Pro Trinket 5V usa el chip Atmega328P, que es el mismo chip central en el Arduino UNO / Duemilanove / Mini / etc. a la misma velocidad y voltaje. Por lo tanto, le alegrará saber que no solo es Pro Trinket programable usando el IDE de Arduino como ya configuró, ¡pero el 99% de los proyectos de Arduino funcionarán de inmediato! Aquí hay algunas cosas que debe tener en cuenta al adaptar los bocetos de Arduino: los pines # 2 y # 7 no están disponibles (están exclusivamente para USB) El regulador de 5 V integrado puede proporcionar una salida de 150 mA, no una salida de 800 mA. No puede enchufar los protectores directamente en Pro Trinket. No hay un chip de serie a USB integrado. Esto es para mantener el Pro Trinket pequeño y económico, puede usar cualquier cable FTDI para conectar al puerto FTDI para una conexión en serie. nnection es solo para cargar código nuevo. El gestor de arranque en Pro Trinket usa 4KB de FLASH, por lo que el tamaño máximo de boceto es de 28,672 bytes. El gestor de arranque no afecta el uso de RAM...

-Titulo Original : Adafruit (PID 3316 VL6180X Time Of Flight Distance Ranging Sensor (VL6180)-Fabricante : Adafruit-Descripcion Original: VL6180X Time of Flight distance sensor // Range: 5mm to 200mm // On Board 5V regulator and level shifting // Works with 3V to 5V // Works with Arduino and other micro controller projects // The VL6180X (sometimes called the VL6180) is a Time of Flight distance sensor like no other you've used! The sensor contains a very tiny laser source, and a matching sensor. The VL6180X can detect the time of flight, or how long the laser light has taken to bounce back to the sensor. Since it uses a very narrow light source, it is good for determining distance of only the surface directly in front of it. Unlike sonars that bounce ultrasonic waves, the 'cone' of sensing is very narrow. Unlike IR distance sensors that try to measure the amount of light bounced, the VL6180X is much more precise and doesn't have linearity problems or 'double imaging' where you can't tell if an object is very far or very close. This is the 'little sister' of the Adafruit VL53L0X ToF sensor, and can handle about 5mm to 200mm of range distance. It also includes a lux sensor. If you need a larger range, check out the VL53L0X which can measure 50 - 1200 mm. The sensor is small and easy to use in any robotics or interactive project. Since it needs 2.8V power and logic we put the little fellow on a breakout board with a regulator and level shifting. You can use it with any 3-5V power or logic microcontroller with no worries. Each order comes with a small piece of header. Solder the header onto your breakout board with your iron and some solder and wire it up for instant distance-sensing-success! Communicating to the sensor is done over I2C with some simple commands. Most of the work is handled inside the sensor itself, so its very easy to port our Arduino library to another microcontroller...

-Titulo Original : Adafruit Audio FX Mini Sound Board - WAV/OGG Trigger 16MB Flash [ADA2341]-Fabricante : Adafruit-Descripcion Original: Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want to make a sound play whenever you press a button. What about something that has to be small and portable? You are probably feeling a little frustrated: it's been very hard to find a simple, low cost audio effects trigger that is easy to use and does not require any programming. Not with the Mini Sound Board! Connect up to 8 buttons or switches, each one can trigger audio files to play. Headphones, powered speakers or even wire up an amplifiers to make loud sounds when plugged into the stereo line out. You can create five different types of triggers which will cover a large range of projects without any programming. What do we mean by trigger effects? Depending on your project you may need to have audio play in different ways. Triggers include Basic, Hold Looping, Latch loop, Play Next, and Play Random. The sound board is designed to be simple: it does not have polyphonic ability, can't play MP3's (MP3 is patented and costs $ to license, so this board uses the similar but not-patented OGG format, there's tons of free converters that will turn an MP3 into OGG), isn't reprogrammable or scriptable, and you can't have any other kind of trigger type. However, there's a good chance the project you want to make will work great. Item Specifics Board Dimensions: 38mm x 23mm x 4mm / 1.5 x 0.9 x 0.2 Board Weight: 3.6...

-Titulo Original : Adafruit Flora RGB Smart NeoPixel Version 2 - Sheet Of 20-Fabricante : Adafruit-Descripcion Original: Designed specifically for wearables // Ultra-bright LEDs with a constant-current driver // Easy to sew and can be daisy-chained // Item Package Quantity: 1 //...

-Titulo Original : Adafruit Feather 32u4 Bluefruit LE [ADA2829]-Fabricante : Adafruit-Descripcion Original: The Bluefruit can also act like an HID Keyboard (for devices that support BLE HID) // Can become a BLE Heart Rate Monitor (a standard profile for BLE) - you just need to add the pulse-detection circuitry // Turn it into a UriBeacon, the Google standard for Bluetooth LE beacons. Just power it and the 'Friend will bleep out a URL to any nearby devices with the UriBeacon app installed. // Built in over-the-air bootloading capability so we can keep you updated with the hottest new firmware. Use any Android or iOS device to get updates and install them. This will update the native code on the BLE module, to add new wireless capabilities, not program the ATmega chip. // This is the Adafruit Feather 32u4 Bluefruit - our take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and battery charging. Its an Adafruit Feather 32u4 with a BTLE module, ready to rock! We have other boards in the Feather family, check'em out here. Bluetooth Low Energy is the hottest new low-power, 2.4GHz spectrum wireless protocol. In particular, its the only wireless protocol that you can use with iOS without needing special certification and it's supported by all modern smart phones. This makes it excellent for use in portable projects that will make use of an iOS or Android phone or tablet. It also is supported in Mac OS X and Windows 8+. At the Feather 32u4's heart is at ATmega32u4 clocked at 8 MHz and at 3.3V logic, a chip setup we've had tons of experience with as it's the same as the Flora. This chip has 32K of flash and 2K of RAM, with built in USB so not only does it have a USB-to-Serial program & debug capability built in with no need for an FTDI-like chip, it can also act like a mouse, keyboard, USB MIDI device, etc. To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin, so you can measure and monitor the battery voltage to detect when you need a recharge. The Feather 32u4 Bluefruit LE uses the extra space left over to add our excellent Bluefruit BTLE module + two status indicator LEDs...

-Titulo Original : Adafruit Metro 328 With Headers - ATmega328-Fabricante : Adafruit-Descripcion Original: Power the METRO with 7-9V polarity protected DC or the micro USB connector to any 5V USB source. The 2.1mm DC jack has an on/off switch next to it so you can turn off your setup easily. The METRO will automagically switch between USB and DC. // METRO has 19 GPIO pins, 6 of which are Analog in as well, and 2 of which are reserved for the USB-serial converter. There's also 6 PWMs available on 3 timers (1 x 16-bit, 2 x 8-bit). There's a hardware SPI port, hardware I2C port and hardware UART to USB. Logic level is 5V but by cutting and soldering closed a jumper, you can easily convert it to 3.3V logic // USB to Serial converter, there's a hardware USB to Serial converter that can be used by any computer to listen/send data to the METRO, and can also be used to launch and update code via the bootloader // Four indicator LEDs, on the front edge of the PCB, for easy debugging. One green power LED, two RX/TX LEDs for the UART, and a red LED connected to pin PB5 // Arduino IDE compatible, you can use this with the Arduino IDE (both desktop and cloud version) by selecting 'Arduino UNO' in the Boards menu. // We sure love the ATmega328 here at Adafruit, and we use them a lot for our own projects. The processor has plenty of GPIO, Analog inputs, hardware UART SPI and I2C, timers and PWM galore - just enough for most simple projects. When we need to go small, we use a Metro Mini or a Trinket M0, but when size isn't as much of a concern, we reach for an Adafruit METRO. This is the Adafruit METRO with headers. It comes with headers soldered on. It's a fully assembled and tested board with through-hole headers attached. If you don't want a Metro with the headers attached for super-slimness, check out our Metro without Headers. METRO is the culmination of years of playing with AVRs: we wanted to make a development board that is easy to use and is hacker friendly. At the heart is an ATmega328P, with 32KB of flash and 2KB of RAM, running at 16 MHz. It comes with the Optiboot bootloader already installed, and is Arduino IDE compatible...

-Titulo Original : Adafruit 3915 Circuit Playground Express Enclosure-Fabricante : Adafruit-Descripcion Original: This enclosure is only compatible with the Circuit Playground Express! // This minimal but elegant acrylic case will turn your board into an electronic snowflake // The enclosure is designed to snap together securely with no tools required // lic case will turn your board into an electronic snowflake. The enclosure is designed to snap together securely with no tools required. You can still press all the buttons and slide the switch thanks to a clever plastic widget fitted inside // The case winds around all the touch pads so you can still touch them or attach alligator clips // We've got nice cases for many of our beloved boards, but the Circuit Playground Express has been left out of couture enclosure game. Enter Ada-friend Mike Doell to the rescue! This minimal but elegant acrylic case will turn your board into an electronic snowflake. The enclosure is designed to snap together securely with no tools required. You can still press all the buttons and slide the switch thanks to a clever plastic widget fitted inside. The case winds around all the touch pads so you can still touch them or attach alligator clips. On the back, we have two slots that can be used to pass through ribbon or webbing up to 1 /2.5mm wide There is also a slim 1/4-20 nut that is embedded in the center back. This is compatible with any camera mounting accessory, so if you need a solid attachment, you can use any camera positioning tool or tripod. Since it's crystal clear, you can see all the NeoPixels shining in glorious color. The light sensor also works just fine and the case will not block IR messages going in or out. Even though there are no microphone or speaker holes, audio passes through the case via various small openings - we tested it and the difference is barely noticeable. This enclosure is only compatible with the Circuit Playground Express! This case will protect your Circuit Playground Express from every day usage, but it is not waterproof or weatherproof. This product comes as 2 molded plastic halves with the buttons in place. No boards, cables, or accessories are included...

-Titulo Original : Adafruit (PID 3010 Feather M0 WiFi - ATSAMD21 ATWINC1500-Fabricante : Adafruit-Descripcion Original: ATSAMD21G18 @ 48MHz with 3.3V logic/power - 256KB FLASH, 32KB SRAM, No EEPROM // This FCC-certified WiFi module works with 802.11b, g, or n networks and supports WEP, WPA and WPA2 encryption // USB native support, comes with USB bootloader and serial port debugging // You also get tons of pins - 20 GPIO pins Hardware Serial, hardware I2C, hardware SPI support 8 x PWM pins 10 x analog inputs 1 x analog output // Measures 2.1" x 0.9" x 0.3" (53.65mm x 23mm x 8mm) without headers soldered in. Note it is 0.1" longer than most Feathers // Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. Its an Adafruit Feather M0 with a WiFi module, ready to rock! We have other boards in the Feather family, check'em out here. Connect your Feather to the Internet with this fine new FCC-certified WiFi module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with built-in low-power management capabilites, Soft-AP, SSL TSL 1.2 support and rock solid performance. We were running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer but we had to go to work, so we unplugged it). This module is very fast and easy to use in comparison to other WiFi modules we've used in the past. This module works with 802.11b, g, or n networks and supports WEP, WPA and WPA2 encryption. You can connect to your own WiFi networks or create your own with Soft AP mode, where it becomes its own access point (we have an example of it creating a webserver that you can then control the Arduino's pins). You can clock it as fast as 12MHz for speedy, reliable packet streaming. And scanning/connecting to networks is very fast, just a second or two. A highly-capable Cortex M0+ processor with ton more I/O pins, lots of 12-bit ADCs, a 10-bit DAC, 6 total SERCOMs that can each do SPI, I2C or UART (3 are used by the existing interfaces, leaving you 3), plenty of timers, PWMs, DMA, native USB, and mor...

-Titulo Original : Adafruit Blue&White 16x2 LCDKeypad Kit For Raspberry Pi [ADA1115]-Fabricante : Adafruit-Descripcion Original: Unfortunately, LCDs require quite a few digital pins, 6 to control the LCD and then another 1 to control the backlight for a total of 7 pins. That's nearly all the GPIO available on a Pi! With this in mind, Adafruit devised a Pi plate that lets you control a 16x2 Character LCD, up to 3 backlight pins AND 5 keypad pins using only the two I2C pins on the R-Pi! The best part is you don't really lose those two pins either, since you can stick i2c-based sensors, RTCs, etc and have them share the I2C bus. This is a super slick way to add a display without all the wiring hassle. This Pi plate has been updated so the buttons on on the right side, which makes it a little more mechanically stable. It is perfect for when you want to build a stand-alone project with its own user interface. The 4 directional buttons plus select button allows basic control without having to attach a bulky computer. Item Specifics Dimensions: 2.2 x 3.35 Plug and play with any Raspberry Pi Uses only the I2C (SDA/SCL) pins This board/chip uses I2C 7-bit address 0x20. Kit Includes: Hight quality PCB 16x2 Blue and White LCD All components (buttons, headers, etc...

-Titulo Original : Adafruit (PID 3505 Metro M0 Express - Designed For CircuitPython - ATSAMD21G18-Fabricante : Adafruit-Descripcion Original: ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328) and 32K of RAM (16x as much)! // This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip. // Power the METRO with 7-9V polarity protected DC or the micro USB connector to any 5V USB source. The 2.1mm DC jack has an on/off switch next to it so you can turn off your setup easily. The METRO will automagically switch between USB and DC. // METRO has 25 GPIO pins, 12 of which are analog in, and one of which is a true analog out. There's a hardware SPI port, hardware I2C port and hardware UART. Logic level is 3.3V // Easy reprogramming, comes pre-loaded with the UF2 bootloader, which looks like a USB storage key. Simply drag firmware on to program, no special tools or drivers needed! It can be used to load up CircuitPython, PXT MakeCode or Arduino IDE (it is bossa-compatible) // Metro is our series of microcontroller boards for use with the Arduino IDE. This new Metro M0 Express board looks a whole lot like our original Metro 328, but with a huge upgrade. Instead of the ATmega328, this Metro features a ATSAMD21G18 chip, an ARM Cortex M0+. It's our first Metro that is designed for use with CircuitPython! CircuitPython is our beginner-oriented flavor of MicroPython - and as the name hints at, its a small but full-featured version of the popular Python programming language specifically for use with circuitry and electronics. Not only can you use CircuitPython, but the Metro M0 is also usable in the Arduino IDE. Native USB, there's no need for a hardware USB to Serial converter as the Metro M0 has built in USB support. When used to act like a serial device, the USB interface can be used by any computer to listen/send data to the METRO, and can also be used to launch and update code via the bootloader. It can also act like a keyboard, mouse or MIDI device as well. Four indicator LEDs and one NeoPixel, on the front edge of the PCB, for easy debugging. One green power LED, two RX/TX LEDs for data being sent over USB, and a red LED connected. Next to the reset button there is an RGB NeoPixel that can be used for any purpose. 2 MB SPI Flash storage chip is included on board. You can use the SPI Flash storage like a very tiny hard drive. When used in Circuit Python, the 2 MB flash acts as storage for all your scripts, libraries and files. When used in Arduino, you can read/write files to it, like a little datalogger or SD card, and then with our helper program, access the files over USB. Comes fully assembled with headers, tested, and with the UF2 bootloader loaded on. We also include 4 rubber bumpers to keep it from slipping off your desk. No soldering required to use, plug and play...

-Titulo Original : Adafruit FONA 808 - Mini Cellular GSM GPS Breakout [ADA2542]-Fabricante : Adafruit-Descripcion Original: Includes GPS and GSM antennas // Quad-band 850/900/1800/1900MHz - connect onto any global GSM network with any 2G SIM (in the USA, T-Mobile is suggested) // Fully-integrated GPS (MT3336 chipset) that can be controlled and query over the same serial port // Make and receive voice calls using a headset or an external 32Ω speaker + electret microphone // Send and receive SMS messages, GPRS data (TCP/IP, HTTP, etc) // Cellular + GPS tracking, all in one? Introducing Adafruit FONA 808 MiniGSM + GPS, an all-in-one cellular phone module with that lets you add location-tracking, voice, text, SMS and data to your project in an tiny package. This module measures only 1.75x1.6 but packs a surprising amount of technology into it's little frame. At the heart is a powerfull GSM cellular module (we use the latest SIM808) with integrated GPS. This module can do just about everything. Onboard LiPoly battery charging circuitry so you can take your project on the go. Use any 500mAh+ LiPoly or LiIon battery and recharge over the MicroUSB when necessary. Two LEDs let you know when its charging and done Standard 4-pole TRRS headphone jack. Use any 'Android' or 'iPhone'-compatible headset with mic Breakouts for external 32Ω speaker and electret mic if you don't want to use a headphone Level shifting circuitry so you can run it with 2.8V to 5V logic. Vibrational motor (buzzer) driver so you can have noiseless notifications uFL connections for external antennas Indicator LEDs for power and network connectivity Standard SIM slides into the back On its own, this module can't do anything. It requires a microcontroller to drive it! We suggest and use an Arduino but any 3-5V microcontroller with a UART can send and receive commands over the RX/TX pins...

-Titulo Original : Adafruit (PID 3357 Music Maker FeatherWing - MP3 OGG WAV MIDI Synth Player-Fabricante : Adafruit-Descripcion Original: Features the VS1053B codec chip - decodes Ogg Vorbis, MP3/MP2/MP1, MP4, AAC, WMA, FLAC, WAV/PCM, MIDI. // SPI Interface // Can play audio from an uSD (micro SD) card // FAT16/FAT32 formatted SD card // Built-in MIDI synth/drum machine with dozens of instruments // Bend all audio files to your will with the Adafruit Music Maker FeatherWing! It's a fun-size version of our Music Maker shield for Arduino! This powerful shield features the VS1053, an encoding/decoding (codec) chip that can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). You can do all sorts of stuff with the audio as well such as adjusting bass, treble, and volume digitally. All this functionality is implemented in a light-weight SPI interface so that any Feather Board can play audio from an SD card. There's also a special MIDI mode that you can boot the chip into that will read 'classic' 31250Kbaud MIDI data from the UART TX pin and act like a synth/drum machine - there are dozens of built-in drum and sample effects! What a great musical add-on to your Feather! That's why we spun up this super FeatherWing, perfect for use with a great many of our Feather Boards! Here are some specs: Features the VS1053B codec chip - decodes Ogg Vorbis, MP3/MP2/MP1, MP4, AAC, WMA, FLAC, WAV/PCM, MIDI. Stereo audio out with proper audio filter caps and ground reference so it can be safely connected directly to headphones, a stereo system or other powered speakers MicroSD card socket, for any FAT16/FAT32 formatted SD card from 64MB or greater Built in MIDI synth/drum machine with dozens of instruments Each order comes with one tested FeatherWing, and two sticks of 0.1 male headers to plug it into your Feather. Some light soldering is required to attach the through-hole headers to the PCB for plugging into your Feather Board. Headphones, SD card and Feather Board not included...

-Titulo Original : Adafruit Pro Trinket - 3V 12MHz-Fabricante : Adafruit-Descripcion Original: The bootloader on the Pro Trinket use 4KB of FLASH so the maximum sketch size is 28,672 bytes // ATmega328P onboad chip in QFN package running at 3.3V logic // Micro-USB jack for power and/or USB uploading, you can put it in a box or tape it up and use any USB cable for when you want to reprogram. // Trinket's got a big sister in town - the Pro Trinket 3V! Pro Trinket combines everything you love about Trinket with the familiarity of the core Arduino chip, the ATmega328. It's like an Arduino Pro Mini with more pins and USB tossed in. Trinket's a year old now, and while its been great to see tons of tiny projects, sometimes you just need more pins, more FLASH, and more RAM. That's why we designed Pro Trinket, with 18 GPIO, 2 extra analog inputs, 28K of flash, and 2K of RAM. Like the Trinket, it has onboard USB bootloading support - we opted for a MicroUSB jack this time. We also added Optiboot support, so you can either program your Pro Trinket over USB or with a FTDI cable just like the Pro Mini and friends. The Pro Trinket PCB measures only 1.5 x 0.7 x 0.2 (without headers) but packs the same capability as an Arduino UNO. So it's great once you've finished up a prototype on an official Arduino UNO and want to make the project smaller. The Pro Trinket 3V uses the Atmega328P chip, which is the same core chip in the Arduino UNO/Duemilanove/Mini/etc. However, it uses 3V logic and 12MHz clock which means it's good when you want a lower-power and lower-voltage setup. Pro Trinket is programmable using the Arduino IDE as you already set up, and 95% of Arduino projects will work out of the box! Here's some things you may have to consider when adapting Arduino sketches: Pins #2 and #7 are not available (they are exclusively for USB) The Pro Trinket 3V runs at 12MHz, this doesn't affect most projects. Only the most timing-specific libraries may be affected, check the documentation! The NeoPixel Library works fine at 12MHz. The onboard power supply is a 3.3V regulator and it can provide 150mA output You cannot plug shields directly into the Pro Trinke...

-Titulo Original : Adafruit Proto Shield For Arduino Kit - Stackable Version R3-Fabricante : Adafruit-Descripcion Original: Kit allows you to choose how you want to configure your shield // Updated for the most compatibility with Arduin // Surface-mount chip area holds up to 14 SOIC size parts // Compatible with tiny breadboards // This prototyping shield is the best out there (well, we think so, at least), and now is even better with Version R3 - updated for the most compatibility with just about all the Arduinos! It has a nice standard 0.1x0.1 prototying grid with big, gold plated pads and comes with stacking headers and plain header, choose whichever you want when soldering together. You will also find A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer. It has a IC pattern for adding DIP ICs, up to 20 pins. The power rails are down the middle and sides. A reset button, an extra general use button and two 3mm general use LEDs, red and green, as well as 2 matching resistors are also included in this kit. Plus, get two 0.1uF capacitors on either side for extra power stability. Comes as a kit of parts Compatible with tiny breadboards. Some soldering skills required. Compatible with regular Arduino headers Dimensions (assembled): 69mm x 53mm x 13mm (2.7in x 2.1in x 0.5in...

-Titulo Original : Adafruit 4132 GPIO Expander Bonnet - 16 Additional I/O Over 12C-Fabricante : Adafruit-Descripcion Original: The Raspberry Pi is an amazing single board computer - and one of the best parts is that GPIO connector! 40 pins of digital goodness you can twiddle to control LEDs, sensors, buttons, radios, displays - just about any device you can imagine. This Adafruit GPIO Expander Bonnet will give you even more digital deliciousness - 16 more digital input/output pins are yours for any desire you have. The outputs are grouped into two 16-pin connectors that have a matching ground pin. You can set each pin to be a digital output (high or low) or as an input, with an internal pull-up if you like! Simply pop the Bonnet on top of your Pi, the circuitry connects to the SDA/SCL I2C pins for control. The MCP23017 chip converts our Python commands to pin instructions. When used as an output, each pin can supply up to 20mA (current clamped) - so you can drive LEDs directly. The datasheet recommends you keep the total current draw to under 125mA for the whole chip. We set up the expander chip for 5V logic by default (the I2C is level shifted so that's 3V logic). We did that so you can drive white, blue or green LEDs that sometimes aren't too happy with 3.3V logic. Or, you can cut/solder a jumper to change it to 3.3V logic. When used as an input, you can set up a pull-up resistor so buttons and switches don't need extra resistors - just wire the pin to one side and ground to the other! There's interrupt capabilities on the chip, and two IRQ pins (INTA and INTB) you can solder a wire to, if you want to have a quick way of telling if any of the GPIO's changed. By soldering close the address select jumpers, you can change the address from 0x20 up to 0x27. So, if you wanted to, you could have up to 8 bonnets for 128 total GPIO. Comes as an assembled and tested Bonnet with slim 2x20 header connector on the bottom. We provide 2 sets of 16-pin IDC sockets, you can solder these in or leave them off for a slim setu...

-Titulo Original : Adafruit (4028 CircuitPython Starter Kit Itsy Bitsy M4-Fabricante : Adafruit-Descripcion Original: You've heard about CircuitPython and maybe you want to get started fast with a breadboard-friendly microcontroller board! We recommend the ItsyBitsy M4 - a super fast chip with tons of GPIO, analog inputs & outputs, with so much RAM that you'll never have to worry about running out of memory. And what better way to get acquainted with ItsyBitsy M4 than with this handy CircuitPython Starter Kit? Small, powerful, with a ultra fast ATSAMD51 Cortex M4 processor running at 120 MHz - this microcontroller board is perfect when you want something very compact, with a ton of horsepower and a bunch of pins. This Itsy is like a bullet train, with it's 120MHz Cortex M4 with floating point support and 512KB Flash and 192KB RAM. Your code will zig and zag and zoom, and with a bunch of extra peripherals for support, this will for sure be your favorite new chipset. We give you a pack of parts for getting started, a lovely Blinka-purple case and even a sticker. Now you've got no excuse for not digging in. Makes for a great workshop pack, hackerspace kit, or gift. Please note the ItsyBitsy M4 is not soldered, some light soldering is required to attach headers to the chip! Once you've got it assembled, tuck it all into the handy carrying case. Includes: 1 x Adafruit ItsyBitsy M4 Express come with loose headers (not shown in the photo but they're in there) 1 x Maker-Friendly Zipper Case in Royal Purple 1 x Half-Size Breadboard 1 x USB Cable - 6 A/microB 1 x Premium Male/Male Jumper Wires set Starter Pack Component Bag 1x Breadboard-friendly SPDT Slide Switch 1x Diffused RGB (tri-color) LED 1x Piezo Buzzer 1x Photo cell light sensor 3x 12mm Tactile Switches 1x Diffused 10mm Red LED 1x Diffused 10mm Green LED 1x 10K Trim Potentiometer 5x 10K 5% 1/4W resistors 5x 560 ohm 5% 1/4W resistor...

-Titulo Original : Adafruit ALS-PT19 Analog Light Sensor Breakout [ADA2748]-Fabricante : Adafruit-Descripcion Original: Add a teeny analog light sensor, the ALS PT19 analog light sensor is a great way to upgrade a project that uses a photocell and needs RoHS compliance. Due to the high rejection ratio of infrared radiation, the spectral response of the ambient light sensor is close to that of human eyes. It's a pretty simple sensor - connect - to ground, + to 2.5V-5.5V or so to power it. Now measure the analog voltage on the OUT pin. That's it! The voltage will increase when the sensor detects more light...

-Titulo Original : Adafruit (PID 3297 DRV8833 DC/Stepper Motor Driver Breakout Board-Fabricante : Adafruit-Descripcion Original: DRV8833 motor driver chip // Spin two DC motors or step one bi-polar or uni-polar stepper with up to 1.2A per channel // 2 full H-bridges // 2.7V to 10.8V motor power // DRV8833 an handle a peak of 2A, but only for a short amount of time // Spin two DC motors or step one bi-polar or uni-polar stepper with up to 1.2A per channel using the DRV8833. This motor driver chip is a nice alternative to the TB6612 driver. Like that chip, you get 2 full H-bridges, but this chip is better for low voltage uses (can run from 2.7V up to 10.8V motor power) and has built in current limiting capability. We set it up for 1A current limiting so you don't get more than 2A per chip, but you can also disable the current limiting, or change it to a different limit! We solder on DRV8833 onto a breakout board for you here, with a polarity protection FET on the motor voltage input. Each breakout chip contains two full H-bridges (four half H-bridges). That means you can drive two DC motors bi-directionally, or one stepper motor. Just make sure they're good for about 1.2 Amp or less of current, since that's the limit of this chip. They do handle a peak of 2A but that's just for a short amount of time, if you turn off the current limiting we set. What we like most about this particular driver is that it comes with built in kick-back diodes internally so you dont have to worry about the inductive kick damaging your project or driver! You also don't have to worry as much about burning out the chip with overdriving since there is current limiting. There's two digital inputs per H-bridge (one for each half of the bridge), you can PWM one of the inputs to control motor speed. Runs at 2.7V-10.8V logic/motor power. The motor voltage is the same as the logic voltage, but logic voltage from 2.7V or greater will work so no need to worry if you are powering the motors from 9V and using 3.3V logic. For higher voltages, check out the TB6612. For much higher voltages and currents check out the DRV8871! Comes as one assembled and tested breakout plus a small strip of header. You'll need to do some light soldering to attach the header onto the breakout PCB. Arduino, motors, and power supply not included...

-Titulo Original : Adafruit Si5351A Clock Generator Breakout Board - 8KHz To 160MHz [ADA2045]-Fabricante : Adafruit-Descripcion Original: Si5351A clock generator (from 8KHz to 150+ MHz) // i2c interface // 3 independent outputs // Outputs are 3Vpp // Includes 3.3V LDO regulator and level shifting circuitry // Never hunt around for another crystal again, with the Si5351A clock generator breakout from Adafruit! This chip has a precision 25MHz crystal reference and internal PLL and dividers so it can generate just about any frequency, from...

-Titulo Original : Adafruit ATWINC1500 WiFi Breakout-Fabricante : Adafruit-Descripcion Original: Connect your Arduino to the Internet with this fine new FCC-certified WiFi module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performance - running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer but we had to go to work, so we unplugged it). We like these so much, they've completely replaced the CC3000 module on all our projects. The Adafruit ATWINC1500 WiFi Breakout uses SPI to communicate, so with about 6 wires, you can get your wired up and ready to go. Right now the Atmel-supplied library works great with Arduino Zero, and seems to work OK on Uno but may not work on other Arduinos. You can clock it as fast as 12MHz for speedy, reliable packet streaming. And scanning/connecting to networks is very fast, a few seconds. This module works with 802.11b, g, or n networks & supports WEP, WPA and WPA2 encryption. The datasheet says it can do Soft-AP mode but we don't have any code to actually use that. Since this is our new favoritest SPI-protocol WiFi module we've decided to make a little breakout for it. The breakout comes with level shifting on all the input pins so you can use it with 3V or 5V logic. A 3.3V voltage regulator that can handle the 300mA spikes lets you power from 3-5.5VDC. There's also 3 LEDs that you can control over the SPI interface (part of the library code) or you can have controlled by the Arduino library. They'll light up when connected to an SSID, or transmitting data...