Arriba

Componentes Electrónicos > Raspberry Pi

Mostrar: 
Mostrar del 1 al 24 (de 41 productos)
Páginas de Resultados:  1  2  [Siguiente >>] 
  • Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit
    Precio:  $6,569.00

    Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit

    -Titulo Original : Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit-Fabricante : ADAFRUIT-Descripcion Original: 4 H-Bridges: TB6612 chipset provides 1.2A per bridge with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC // Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) // Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping. // Big terminal block connectors to easily hook up wires (18-26AWG) and power // Works best with Raspberry Pi model A+, B+, or Pi 2, but can be used with a model A or B if you purchase a 2x13 extra-tall header and solder that instead of the 2x20 // Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Since the Raspberry Pi does not have a lot of PWM pins, we use a fully-dedicated PWM driver chip onboard to both control motor direction and speed. This chip handles all the motor and speed controls over I2C. Only two pins (SDA & SCL) are required to drive the multiple motors, and since it's I2C you can also connect any other I2C devices or HATs to the same pins. In fact, you can even stack multiple Motor HATs, up to 32 of them, for controlling up to 64 stepper motors or 128 DC motors (or a mix of the two) - just remember to purchase and solder in a stacking header instead of the one we include. Motors are controlled by TB6612 MOSFET drivers with 1.2A per channel current capability (you can draw up to 3A peak for approx 20ms at a time), a big improvement over L293D drivers and there are built-in flyback diodes as well. We even had a little space so we added a polarity protection FET on the power pins and a bit of prototyping area. And the HAT is assembled and tested here at Adafruit so all you have to do is solder on the included 2x20 plain header and the terminal blocks. Install the easy-to-use Python library, check out the examples and you're ready to go! Comes with an assembled & tested HAT, terminal blocks, and 2x20 plain header. Some soldering is required to assemble the headers o...
  • Raspberry Pi NoIR Camera Module V2 - 8MP 1080P30
    Precio:  $8,429.00

    Raspberry Pi NoIR Camera Module V2 - 8MP 1080P30

    -Titulo Original : Raspberry Pi NoIR Camera Module V2 - 8MP 1080P30-Fabricante : RASPBERRY PI-Descripcion Original: Computer accessories, Computers | Electronics, Electronics | Peripherals and spares // Color:Multicolor Link to blog - how to get started with the camera module - with sample script ...
  • Raspberry Pi 3 Starter Kit [official Raspberry]
    Precio:  $50,969.00

    Raspberry Pi 3 Starter Kit [official Raspberry]

    -Titulo Original : Raspberry Pi 3 Starter Kit [official Raspberry]-Fabricante : RASPBERRY PI-Descripcion Original: Offical & Original Raspberry Pi 3 Starter Kit // To celebrate the sale of their ten millionth Raspberry Pi, the Raspberry Pi Foundation for the first time has put together their own idea of what the perfect bundle would look like, creating the official Raspberry Pi Starter Kit. This kit provides you with a keyboard, mouse, power supply, Pi enclosure, HDMI cable, and an SD card with the necessary operating system out of which you can operate. Great for setting you on the path to building your own computer -- all you'd need to wrap it up is an HDMI monitor or television! Kit includes: A Raspberry Pi 3 Model B An 8GB NOOBS SD card An official case An official 2.5A multi-region power supply An official 1m HDMI cable An optical mouse and a keyboard (QWERTY) with high-quality scissor-switch action A copy of Adventures in Raspberry Pi Foundation Edition The Pi Foundation has called this an unashamedly premium product: the latest Raspberry Pi, official accessories, the best USB peripherals we could find, and a copy of the highest-rated Raspberry Pi book. It doesn't get any more official than that...
  • Arduino Due sin encabezados A000056
    Precio:  $12,769.00

    Arduino Due sin encabezados A000056

    -Titulo Original : Arduino Due Without Headers A000056 -Fabricante : Arduino -Descripcion Original: ¡Arduino genuino! La Arduino Due es la primera placa Arduino basada en un microcontrolador de núcleo ARM de 32 bits. Con 54 pines de entrada / salida digital, 12 entradas analógicas, es la placa perfecta para proyectos de Arduino potentes a gran escala. 512 KB de memoria flash El Arduino Due es una placa de microcontrolador basada en la CPU Atmel SAM3X8E ARM Cortex-M3. Es la primera placa Arduino basada en un microcontrolador de núcleo ARM de 32 bits. Tiene 54 pines de entrada / salida digital (de los cuales 12 se pueden usar como salidas PWM), 12 entradas analógicas, 4 UART (puertos serie de hardware), un reloj de 84 MHz, una conexión USB OTG capaz, 2 DAC (digital a analógico) , 2 TWI, un conector de alimentación, un encabezado SPI, un encabezado JTAG, un botón de reinicio y un botón de borrado. Advertencia: a diferencia de la mayoría de las placas Arduino, la placa Arduino Due funciona a 3,3 V. El voltaje máximo que pueden tolerar los pines de E / S es de 3,3 V. La aplicación de voltajes superiores a 3,3 V a cualquier pin de E / S podría dañar la placa. La placa contiene todo lo necesario para soportar el microcontrolador; simplemente conéctelo a una computadora con un cable micro-USB o enciéndalo con un adaptador de CA a CC o una batería para comenzar. El Due es compatible con todos los protectores Arduino que funcionan a 3.3V y son compatibles con el pinout 1.0 Arduino. El Due sigue el pinout 1.0: TWI: pines SDA y SCL que están cerca del pin AREF. IOREF: permite un blindaje adjunto con la configuración adecuada para adaptarse a la tensión proporcionada por la placa. Esto permite la compatibilidad del escudo con una placa de 3,3 V como las placas basadas en Due y AVR que funcionan a 5 V. Un pin no conectado, reservado para uso futuro. ...
  • Adafruit Flex Cable for Raspberry Pi Camera - 300mm / 12...
    Precio:  $1,829.00

    Adafruit Flex Cable for Raspberry Pi Camera - 300mm / 12...

    -Titulo Original : Adafruit Flex Cable for Raspberry Pi Camera - 300mm / 12 [ADA1648]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1648 // Stock Type: Raspberry Pi >> Cables >> Camera // In Stock & Ready to Ship // This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 300mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those in the shop as well) Flex Cable for Raspberry Pi Camera - 300mm / 12 ( 7:45 ...
  • Raspberry Pi 3 A+ Computer Board
    Precio:  $14,209.00

    Raspberry Pi 3 A+ Computer Board

    -Titulo Original : Raspberry Pi 3 A+ Computer Board-Fabricante : RASPBERRY-Descripcion Original: Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz // 512MB LPDDR2 SDRAM // 2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2/BLE // Extended 40-pin GPIO header // Full-size HDMI // 1.4GHz 64-bit quad-core processor, dual-band wireless LAN, Bluetooth 4.2/BLE in the same mechanical format as the Raspberry Pi 1 Model A...
  • Raspberry Pi 16GB Preloaded (Noobs) SD Card …
    Precio:  $4,569.00

    Raspberry Pi 16GB Preloaded (Noobs) SD Card …

    -Titulo Original : Raspberry Pi 16GB Preloaded (Noobs) SD Card …-Fabricante : RASPBERRY PI-Descripcion Original: Genuine 16GB SanDisk Ultra Class 10 MicroSD Card (Red/White) with adapter // Works with all Raspberry Pi Models // Fully Qualified by the Raspberry Pi Foundation for Optimum Performance // Preloaded with the NOOBS Operating System // Raspberry Pi 16GB Preloaded (NOOBS) SD Card &hellip...
  • ContempoViews Intermediate Starter Kit para Raspberry Pi B + 2 & 3 RPi Learning Kit 1210
    Precio:  $12,109.00

    ContempoViews Intermediate Starter Kit para Raspberry Pi B + 2 & 3 RPi Learning Kit 1210

    -Titulo Original : ContempoViews Intermediate Starter Kit for Raspberry Pi B+ 2 & 3 RPi Learning Kit 1210-Fabricante : Contempo Views-Descripcion Original: Advanced learning kit intended for those with some experience with RPi or Arduino // Over 35 different components // Nearly 100pcs in total // Numerous electronic components to enhance your Raspberry Pi experience // This is an advanced learning kit for Raspberry Pi. It is equipped with more interesting and powerful functional modules than the basic starter kit, and so it is more suitable for those who have already had some relevant knowledge. This advanced version provides more abundant learning materials and more space for creating some interesting interactive projects. Raspberry Pi is a credit card sized single-board computer, through which we can learn relevant knowledge about Linux operating systems as well as C and python language based on Raspberry Pi debian (based on linux) system, not to mention sensor/module applications on Raspberry Pi. Arduino and Raspberry Pi are a great match for each other. - 10MM Full color high-brightness sensor x 1 - Home appliances control module x 1 - Raspberry Pi GPIO V2 shield x 1 - High-quality 830 hole breadboard x 1 - MAX7219 dot matrix module x 1 - 9g servo x 1 - ULN2003 driving board x 1 - Black remote control x 1 - 5V step motor x 1 - 50K adjustable potentiometer x 1 - 801S vibration sensor x 1 - PS2 game rocker module x 1 - Four-bit digital tube x 1 - One-bit digital tube x 1 - 74H595 IC x 1 - Red LED x 5 - Blue LED x 5 - Yellow LED x 5 - 1K resistor x 5 - 10K resistor x 5 - 220R resistor x 8 - DHT11 Humiture sensor x 1 - DS3231 clock x 1 - PCF8591 AD/DA conversion module x1 - Yellow button cap x 4 - Infrared receiver component x 1 - LM35 component x 1 - Flame component x 1 - Ball component x 2 - Light-sensitive component x 3 - Mini LCD screen x 1 - 40Pin colorful flat cable x 1 - Membrane keypad x 1 - Dupont Cable x 30 - Male to female dupont cable/20-row x 1 - SR04 ultrasonic x ...
  • Set De 4 Joystick Arcade Mame Raspberry Pi / Usb Pc
    Precio:  $33,299.00

    Set De 4 Joystick Arcade Mame Raspberry Pi / Usb Pc

    -Titulo Original : 4 Player LED Arcade DIY Kit for USB MAME PC Game DIY & Raspberry Pi Retro Controller DIY Including 4X Arcade Joystick, 40x LED Chrome Arcade Buttons 2X Zero Delay USB Encoder-Fabricante : EG STARTS-Descripcion Original: Este es un juego de piezas de bricolaje LED para proyectos de bricolaje para 2 jugadores. ¡El codificador admite todos los sistemas de Windows! Todas las partes no son originales de Sanwa. Recién hecho en piezas de China, todos los botones no son de metal. Si el LED no se enciende. Luego, cambie la interfaz del LED de ubicación. ¡Cada codificador tiene su propio cable USB para asegurarse de que el modo multijugador puede jugar en las mismas condiciones! ¡El Joystick es un joystick profesional de 8 vías! Los botones son botones LED de 5V iluminados con microinterruptores incorporados en el interior. Los botones predeterminados están iluminados todo el tiempo. Si compra uno de este artículo, ¿Qué incluirá en el paquete? Codificador USB 4x Zero Delay LED 4x cable USB 4x cables de 5 pines para Joystick 40x cables de 3 pines para botones LED Joystick 4x 5 pines de 8 vías (1x rojo, 1x amarillo, 1x azul, 1x verde) 1x 1 jugador más grande 5V LED cromo pulsadores (blanco) con lámpara LED y micro interruptor 1x 2 jugadores más grandes 5V LED botones de cromo (blanco) con lámpara LED y micro interruptor 1x 3 jugadores más grandes botones de cromo LED de 5V (blanco) con lámpara LED y micro interruptor 1x 4 jugadores más grandes 5V LED botones de cromo (blanco) con lámpara LED y micro interruptor 4x Coin Botones de cromo LED de 5V más grandes (blanco) con lámpara LED y micro interruptor 32x botones LED cromados de 5V más grandes con LED y micro interruptor (8x rojo, 8x amarillo, 8x azul, 8x verde) 1x instrucciones Consejos para la instalación. 1. Por favor lea nuestro manual de usuario antes de comenzar sus acciones de bricolaje. 2. ¡Es muy importante! Conecte el cable de 5 pines del Joystick a la ranura de 5 pines que se encuentra frente al terminal USB-B. Mucha gente conecta el joystick a la ranura incorrecta de 5 pines. 3. No es necesario separar las funciones del botón cuando conectas el cable a los botones y al panel de codificador, excepto que deseas agregar las funciones Auto-Fire, Tubro, Clear y Mode. Todas las funciones del botón de lucha pueden ser establecido en MAME o RetroPie. Las funciones Auto-Fire, Tubro, Clear y Mode tienen su propia ranura en la placa del codificador. 4. Para jugadores profesionales. Sugerimos que cambie todos los botones y joysticks a SANWA Brand o SEIMITSU Brand. Consejos para nuevos usuarios: 1. El artículo necesita trabajar con el emulador MAME. Entonces, antes de construir su propio proyecto, descargue uno para trabajar con las piezas. 2. Si usa este kit para construir sus propios proyectos de frambuesa Pi Retropie. Busque los pasos antes de su bricolaje...
  • Adafruit Flex Cable For Raspberry Pi Camsra O Display 300mm
    Precio:  $2,029.00

    Adafruit Flex Cable For Raspberry Pi Camsra O Display 300mm

    -Titulo Original : Adafruit Flex Cable for Raspberry Pi Camera or Display - 300mm / 12-Fabricante : ADAFRUIT-Descripcion Original: Dimensions: 50mm x 16mm (2" x 0.6") // This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. // This cable is 50mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those in the shop as well) // Available in 50mm (2"), 100mm (4"), 200mm (8"), 300mm (12") Lengths // Raspberry Pi & Camera Board NOT included // This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 50mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those in the shop as well...
  • Adafruit Ultimate GPS HAT for Raspberry Pi A+ or B+ Mini Kit
    Precio:  $14,409.00

    Adafruit Ultimate GPS HAT for Raspberry Pi A+ or B+ Mini Kit

    -Titulo Original : Adafruit Ultimate GPS HAT for Raspberry Pi A+ or B+ Mini Kit-Fabricante : ADAFRUIT-Descripcion Original: 165 dBm sensitivity, 10 Hz updates, 66 channels // Built in Real Time Clock (RTC) - slot in a CR1220 backup battery for 7-years or more of timekeeping even if the Raspberry Pi is off! // Internal patch antenna which works quite well when used outdoors + u.FL connector for external active antenna for when used indoors or in locations without a clear sky view // Fix status LED blinks to let you know when the GPS has determined the current coordinates // Raspberry Pi *not* included // This new HAT from Adafruit adds their celebrated Ultimate GPS on it, so you can add precision time and location to your Raspberry Pi Model A+ or B+ We spun up a HAT based on our Ultimate GPS, added a coin-cell holder for RTC usage, break-outs for all the Raspberry Pi's extra pins, and plenty of prototyping area for adding LEDs, sensors, and more. Please note, this HAT takes over the Raspberry Pi's hardware UART to send/receive data to and from the GPS module. So, if you need to use the RX/TX pins with a console cable, you cannot also use this HAT. Instead, you'll have to use a composite or HDMI monitor and keyboard to log in, or use ssh to connect over the network to your Pi. Read up on Adafruit's tutorial for more information on how to use this fine HAT. Comes as a fully assembled GPS + PCB and an additional 2x20 GPIO header. Some light soldering is required to attach the 2x20 GPIO header to the HAT but it's fast and easy for anyone with a soldering iron and solder. This HAT does not come with a 12mm coin battery! A CR1220 will let you use the real-time-clock capability of the GPS HAT...
  • Raspberry Pi Zero W (Wireless) ( 2017 model)
    Precio:  $8,139.00

    Raspberry Pi Zero W (Wireless) ( 2017 model)

    -Titulo Original : Raspberry Pi Zero W (Wireless) ( 2017 model)-Fabricante : RASPBERRY PI-Descripcion Original: Raspberry Pi Zero W // SoC: Broadcom BCM2835--CPU: ARM11 running at 1GHz--RAM: 512MB // Wireless: 2.4GHz 802.11n wireless LAN (WiFi) // Bluetooth: Bluetooth Classic 4.1 and Bluetooth LE // Dimensions: 65mm × 30mm × 5mm // Dimensions: 65mm × 30mm × 5mm SoC: Broadcom BCM2835 CPU: ARM11 running at 1GHz RAM: 512MB Wireless: 2.4GHz 802.11n wireless LAN Bluetooth: Bluetooth Classic 4.1 and Bluetooth LE Power: 5V, supplied via micro USB connector Video & Audio: 1080P HD video & stereo audio via mini-HDMI connector Storage: MicroSD card Output: Micro USB GPIO: 40-pin GPIO, unpopulated Pins: Run mode, unpopulated; RCA composite, unpopulated Camera Serial Interface (CSI...
  • Cable Flexible Flat 30 Pins 0.5mm Pitch 300mm (tipo A)
    Precio:  $2,649.00

    Cable Flexible Flat 30 Pins 0.5mm Pitch 300mm (tipo A)

    -Titulo Original : uxcell Flexible Flat Cable, 30 Pins 0.5mm Pitch 300mm FPC FFC Flexible Ribbon Cable for LCD TV Car Audio DVD Player Laptop (A Type) -Fabricante : uxcell -Descripcion Original: Reemplazo para el siguiente modelo de batería / números de pieza: CP-HK03. Destinado / Compatible con los siguientes modelos de altavoces Bluetooth: Harman Kardon Esquire 2, HKESQUIRE2BLK, HKESQUIRE2GLD, HKESQUIRE2GR. Paquete de baterías recargables de polímero de litio de 3.7V 2800mAh 10.36Wh...
  • Raspberry Pi HAT Enclosure
    Precio:  $2,369.00
    Expira: 06/05/2021

    Raspberry Pi HAT Enclosure

    -Titulo Original : Raspberry Pi HAT Enclosure-Fabricante : RASPBERRY PI-Descripcion Original: 3-Part Enclosure: Removable Cover, Top, and Base Frame // Fits standard-size Raspberry Pi HATs // All ports are accessible // Compatible with the Raspberry Pi 3 Model B, Raspberry Pi 2, and Raspberry Pi B+. // NOTE: SenseHAT NOT Included. // This clever enclosure features a removable top cover that allows full access to standard-size Pi HATS. It's a great way to keep your Pi safe while experimenting and expanding it's capabilities...
  • Raspberry Pi 2 Model B Desktop (Quad Core CPU 900 MHz, 1 GB.
    Precio:  $12,009.00

    Raspberry Pi 2 Model B Desktop (Quad Core CPU 900 MHz, 1 GB.

    -Titulo Original : Raspberry Pi 2 Model B Desktop (Quad Core CPU 900 MHz, 1 GB RAM, Linux)-Fabricante : RASPBERRY PI-Descripcion Original: Quad-core ARM Cortex-A7 CPU 0.9 GHz // 1GB SDRAM // Audio: 3.5 mm jack, Storage: microSD card slot, Network: 10/100 Mb/s // Power: Micro USB DC 5 V 800 mA for the Pi board // Style: The latest addition to the Raspberry Pi family, the Raspberry Pi 2 Model B takes the platform to a completely new level. Combining a six fold increase in processing power and a doubling of memory capacity with complete backward compatibility with the existing Model B Plus, Raspberry Pi 2 Model B is the perfect board for professionals and hobbyists alike. The new Raspberry Pi 2 Model B is jam packed with features. With a new quad core processor and twice the memory with a massive 1GB RAM. It's a whopping 6x faster than its predecessor. The ultra-low-cost, deck-of-cards sized Linux computer has had a makeover, and it's a good one at that. Required items to get up and running are: MicroSD card, Power Supply, Keyboard, Mouse, and HDMI compatible display. Note: The Raspberry Pi 2 boards by element14/Premier Farnell are Made in China (PRC) as well as United Kingdom...
  • Raspberry Pi 3 Model B Motherboard
    Precio:  $12,279.00

    Raspberry Pi 3 Model B Motherboard

    -Titulo Original : Raspberry Pi 3 Model B Motherboard-Fabricante : RASPBERRY PI-Descripcion Original: ✔ Modular Design: Modular designed Half cage for Fujifilm X-T3 and X-T2 Camera with battery grip // ✔ Dovetail Plate for Arca-Type: Compatible dovetail plate for Arca-Type with center marks on both axis // ✔ 2 Using Ways: The top plate can be removed, and the top plate and half cage can be used separately // ✔ Built-in Slot: Features a slot on the bottom allows to extend camera for tethering or cable release // ✔ Built-in Flat Screw Driver: Built-in flat screw driver on the bottom for quick adjustment // Color: A professional company specializing in camera accessories. A comprehensive enterprise integrating product design, research and development, sales and maintenance of camera accessories. Products are sold in the United States, China, Germany, France, Japan, Canada, Australia and other countries. We take high-quality products as the core and excellent customer service as our tenet.is a modular designed half cage with anti-twist flanges to keep the camera from twisting and provide multiple mounting points. Optional top plate is locked via a M4 screw and a shoe lock to prevent twisting.The top plate can be removed.The top plate and the half cage can be used separately.✔ The top plate comes with an arri 3/8”hole and integrate with a cold shoe for more accessories attachment if needed.✔ It features multiple 1/4-20 threaded holes on the side and bottom for accessory attachment, such as cold shoe 1593 for microphone.✔ Design for Fujifilm X-T3 with VG-XT3 Vertical Battery Grip✔ Design for Fujifilm X-T2 with VPB-XT2 Vertical Battery Grip✔ Product Dimensions: 108X 64X155mm✔ Package Dimensions: 143 x 100 x55mm✔ Net Weight: 190g✔ Package Weight: 235g✔ Material(s): Aluminum Alloy✔ 1 x Bottom Plate✔ 1 x Side Plate✔ 1 x Top Plate✔ 3 x M4 Screw✔ 1x Hex SpannerAt SMALLRIG, not only we offer high quality products,we back them up with 18-month warranty and a 30-day money back guarant...
  • Set De 2 Joystick Arcade Mame Raspberry Pi / Usb Pc
    Precio:  $15,149.00

    Set De 2 Joystick Arcade Mame Raspberry Pi / Usb Pc

    -Titulo Original : Fosiya 2 Player Arcade Games Ellipse Oval Style 8 Ways Joystick + 20 x LED Chrome Arcade Buttons for Video Games Standard Controllers All Windows PC MAME Raspberry Pi (Mixed Colors Chrome Buttons)-Fabricante : Fosiya-Descripcion Original: Excellent Control USB Encoder. High Quality Ellipse Oval Style 8 way joystick. LED Buttons Good lighting effects. Perfect LED illuminated parts for 2 player Arcade MAME Jamma and other fighting game DIY Project! Made with highest quality materials! Heat resistant plastic! Environmentally friendly metal! Includes: 2 x 5Pin Arcade Joystick + 2 x USB Encoder + 20 x Chrome plated LED button (1 Player + 2 Player + 2x Coin button). Chrome LED Illuminated push buttons with build-in Blue switch inside, excellent electronic performance, long life, reliability tested to 3,000,000 cycles...
  • Adafruit RGB Matrix HAT + RTC for Raspberry Pi - Mini Kit
    Precio:  $8,649.00

    Adafruit RGB Matrix HAT + RTC for Raspberry Pi - Mini Kit

    -Titulo Original : Adafruit RGB Matrix HAT + RTC for Raspberry Pi - Mini Kit-Fabricante : ADAFRUIT-Descripcion Original: Simple design - plug in power, plug in IDC cable, and run Adafruit's Python code. // Onboard level shifters to convert the RasPi's 3.3V to 5.0V logic for clean matrix driving. // Works with Adafruit 16x32, 32x32 or 32x64 RGB LED Matrices with HUB75 connections. You can even chain multiple matrices together for a longer display. // Included: RGB Matrix HAT controller. NOT Included: RGB LED Matrix (sold separately), Raspberry Pi, 5V power supply, or coin cell battery for Real Time Clock. (Real Time Clock not needed for unit to function) // You can now create a dazzling display with your Raspberry Pi Model A+/B+/Pi 2 or Pi 3 with the Adafruit RGB Matrix HAT. This HAT plugs into your Pi and makes it super easy to control RGB matrices such as those we stock in the shop and create a colorful scrolling display or mini LED wall with ease. Each order comes with a HAT PCB with all surface mount parts assembled, a 2x20 female socket connector, a 2 pin terminal block, and a 2x8 IDC socket connector. A CR1220 coin cell is not included (required for real time clock). A 5V power supply is also required, not included, for powering the matrix itself. The Pi cannot do it due to the high currents. To calculate the max current of your matrix set up, multiply the width of all the chained matrix by 0.12 : A 32 pixel wide matrix needs 32*0.12 = 3.85A so pick up a 5V 4A power supply...
  • Adafruit Flex Cable for Raspberry Pi Camera - 24 / 610mm
    Precio:  $2,219.00

    Adafruit Flex Cable for Raspberry Pi Camera - 24 / 610mm

    -Titulo Original : Adafruit Flex Cable for Raspberry Pi Camera - 24 / 610mm-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1731 // Stock Type: Raspberry Pi >> Cables >> Camera // In Stock & Ready to Ship // This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 24 / 610mm long We have cables in 2, 4, 8, 12, and 18 long so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those in the shop as well)...
  • Raspberry Pi 32gb Preloaded (noobs) Sd Card
    Precio:  $5,669.00

    Raspberry Pi 32gb Preloaded (noobs) Sd Card

    -Titulo Original : Raspberry Pi 32GB Preloaded (NOOBS) SD Card-Fabricante : RASPBERRY PI-Descripcion Original: Official 32GB MicroSD Card and Full-Size Adapter // Fully Qualified by the Raspberry Pi Foundation for Optimum Performance // Preloaded with the NOOBS Operating System // Works with all Raspberry Pi Models // Raspberry Pi Foundation Official 32GB MicroSD Card with Full-Size Adapter. Fully Qualified by the Raspberry Pi Foundation for Optimum Performance. Preloaded with the NOOBS Operating System. Works with all Raspberry Pi Models. SanDisk Ultra Class 10 MicroSD Card in OEM (black color) packaging...
  • Cable de datos USB para Action Replay DS/DSi/3DS de Nintendo
    Precio:  $12,649.00

    Cable de datos USB para Action Replay DS/DSi/3DS de Nintendo

    -Titulo Original : Cable de datos USB para Action Replay DS/DSi/3DS de Nintendo-Fabricante : GodMod...
  • Adafruit Smt Gpio Header For Raspberry Pi Hat - 2x20 Short.
    Precio:  $2,499.00

    Adafruit Smt Gpio Header For Raspberry Pi Hat - 2x20 Short.

    -Titulo Original : Adafruit SMT GPIO Header for Raspberry Pi HAT - 2x20 Short Female Header [ADA2187]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2187 // Stock Type: Raspberry Pi >> Raspberry Pi B+, Pi 2, & Pi 3 >> Prototyping // In Stock & Ready to Ship // For super-slim SMT designs, this custom-made, 2x20 short SMT female header can be used to plug a Raspberry Pi HAT onto a B+ or A+ or Pi 2. It's harder to use than the Thru-Hole type headers, but for the slickest, slimmest fit, this header is recommended...
  • PiTFT Plus 480x320 3.5 TFT+Touchscreen for Raspberry Pi - Pi
    Precio:  $14,099.00

    PiTFT Plus 480x320 3.5 TFT+Touchscreen for Raspberry Pi - Pi

    -Titulo Original : PiTFT Plus 480x320 3.5 TFT+Touchscreen for Raspberry Pi - Pi 2 and Model A+ / B+-Fabricante : ADAFRUIT-Descripcion Original: This PiTFT 3.5" is designed to fit nicely onto the Raspberry Pi 2 or Model A+ / B+, not compatible with original Model A and Model B // Comes fully assembled and ready to plug into your Pi! (See not below) // You can also have an HDMI display separately connected.(This may be required during initial setup) // Features a 3.5" display with 480x320 16-bit color pixels and a resistive touch overlay // Important Note: This product requires configuration and driver setup to work correctly on the PI and is not "plug and play". Many users report a "white" screen indicating the PI has not been configured correctly. Please see Adafruit Documentation or contact the seller if you experience this issue. Raspberry Pi Not included // Color: Is this not the cutest, little display for the Raspberry Pi? It features a 3.5 display with 480x320 16-bit color pixels and a resistive touch overlay just like our popular original, but this one is engineered specifically to work with the Raspberry Pi 2 and the Model A+ / B+. The plate uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top! This PiTFT 3.5 is designed to fit nicely onto the Raspberry Pi 2 or Model A+ / B+. If you'd like to use a 3.5 display with the original Pi A or Pi B, check out this version The display uses the hardware SPI pins (SCK, MOSI, MISO, CE0, CE1) as well as GPIO #25 and #24. GPIO #18 can be used to PWM dim the backlight if you like. All other GPIO are unused. There's a 2x16 'classic Pi' connection GPIO header on the bottom, you can connect a 26-pin Pi GPIO cable to it to use any of the other pins as you like. The other GPIO are broken out into solder pads at the bottom, in case you want to use more of the GPIO. Best of all, it comes fully assembled and ready to plug into your Pi! You can use this as a display for running the X interface, or pygame. You can also have an HDMI display seperately connected. There's four mounting ears that can be used to attach the display & Pi to a bezel, or snap them off with pliers (they're perforated) for a slick exactly-the-same-size-as-a-Pi look. Adafruit created a custom kernel package based of off Notro's awesome framebuffer work, so you can install it over your existing Raspbian (or derivative) images in just a few commands. Adafruit's tutorial shows you how to install the software, as well as calibrate the touchscreen, display images such as from your PiCam and more! Please visit Adafruit for more informatio...
  • Raspberry Pi 3 Case - Black/Grey
    Precio:  $3,029.00

    Raspberry Pi 3 Case - Black/Grey

    -Titulo Original : Raspberry Pi 3 Case - Black/Grey-Fabricante : RASPBERRY PI-Descripcion Original: Official case for the Raspberry Pi from the Raspberry Pi Foundation // Removable Lid provides easy access to the camera and display ports // Removable Side Panels with easy access to the GPIO port // Removable Top Frame // Designed with Pi HAT's in mind // The Official Case of the Raspberry Pi Foundation has been refreshed for the Pi 3. Designed with HATs in mind and featuring multiple removable panels. Enclose your board as much or as little as necessary to best suit your latest project...
Mostrar del 1 al 24 (de 41 productos)
Páginas de Resultados:  1  2  [Siguiente >>]