Arriba

Componentes Electrónicos > Raspberry Pi

Mostrar: 
Mostrar del 1 al 24 (de 52 productos)
Páginas de Resultados:  1  2  3  [Siguiente >>] 
  • Raspberry Pi 3 A+ Computer Board
    Precio:  $5,933.00

    Raspberry Pi 3 A+ Computer Board

    -Titulo Original : Raspberry Pi 3 A+ Computer Board-Fabricante : RASPBERRY-Descripcion Original: Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz // 512MB LPDDR2 SDRAM // 2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2/BLE // Extended 40-pin GPIO header // Full-size HDMI // 1.4GHz 64-bit quad-core processor, dual-band wireless LAN, Bluetooth 4.2/BLE in the same mechanical format as the Raspberry Pi 1 Model A...
  • Adafruit Aluminum Heat Sink for Raspberry Pi 3 - 15 x 15 x..
    Precio:  $1,131.00

    Adafruit Aluminum Heat Sink for Raspberry Pi 3 - 15 x 15 x..

    -Titulo Original : Adafruit Aluminum Heat Sink for Raspberry Pi 3 - 15 x 15 x 15mm [ADA3082]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 3082 // Stock Type: Components & Parts >> Heat Sinks // In Stock & Ready to Ship // Looking for the best heat sink for your Raspberry Pi 3 ? Check out this nice and tall This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi   but is best paired with a Raspberry Pi 3 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy. Clean the surface of the chip of any dust or grease then peel off the protective film and press the heat sink firmly onto the chip. You can use this heatsink with any of our injection molded Adafruit Pi Enclosures , but it may not work with other enclosures and most HATs will not fit on top with the heat sink installed.We don't have formal specs for this heat sink, but when we ran 'stress -c 4' on the Pi 3 to run all 4 CPUs, a heat-sink-less Pi quickly dropped down to 0.96 GHz to maintain thermal equilibrium. With this heat sink installed, it could run at 1.16GHz (so, 20% higher performance)Note that you do not need a heatsink for the Pi 3, it will automatically adjust its speed to avoid overheating! It can also, of course, be used for other processors and chips...
  • Raspberry Pi 3 Case - Black/Grey
    Precio:  $1,535.00

    Raspberry Pi 3 Case - Black/Grey

    -Titulo Original : Raspberry Pi 3 Case - Black/Grey-Fabricante : RASPBERRY PI-Descripcion Original: Official case for the Raspberry Pi from the Raspberry Pi Foundation // Removable Lid provides easy access to the camera and display ports // Removable Side Panels with easy access to the GPIO port // Removable Top Frame // Designed with Pi HAT's in mind // The Official Case of the Raspberry Pi Foundation has been refreshed for the Pi 3. Designed with HATs in mind and featuring multiple removable panels. Enclose your board as much or as little as necessary to best suit your latest project...
  • Raspberry Pi 3 Starter Kit [official Raspberry]
    Precio:  $23,643.00

    Raspberry Pi 3 Starter Kit [official Raspberry]

    -Titulo Original : Raspberry Pi 3 Starter Kit [official Raspberry]-Fabricante : RASPBERRY PI-Descripcion Original: Offical & Original Raspberry Pi 3 Starter Kit // To celebrate the sale of their ten millionth Raspberry Pi, the Raspberry Pi Foundation for the first time has put together their own idea of what the perfect bundle would look like, creating the official Raspberry Pi Starter Kit. This kit provides you with a keyboard, mouse, power supply, Pi enclosure, HDMI cable, and an SD card with the necessary operating system out of which you can operate. Great for setting you on the path to building your own computer -- all you'd need to wrap it up is an HDMI monitor or television! Kit includes: A Raspberry Pi 3 Model B An 8GB NOOBS SD card An official case An official 2.5A multi-region power supply An official 1m HDMI cable An optical mouse and a keyboard (QWERTY) with high-quality scissor-switch action A copy of Adventures in Raspberry Pi Foundation Edition The Pi Foundation has called this an unashamedly premium product: the latest Raspberry Pi, official accessories, the best USB peripherals we could find, and a copy of the highest-rated Raspberry Pi book. It doesn't get any more official than that...
  • Adafruit Ultimate GPS HAT for Raspberry Pi A+/B+/Pi 2...
    Precio:  $7,515.00

    Adafruit Ultimate GPS HAT for Raspberry Pi A+/B+/Pi 2...

    -Titulo Original : Adafruit Ultimate GPS HAT for Raspberry Pi A+/B+/Pi 2 [ADA2324]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2324 // Stock Type: Raspberry Pi >> Pi HATs & Plates >> Hats // In Stock & Ready to Ship // It's 10PM, do you know where your Raspberry Pi is? If you had this GPS HAT, you would! This new HAT from Adafruit adds our celebrated Ultimate GPS on it, so you can add precision time and location to your Raspberry Pi Model A+, B+, or Pi 2. Does not work with the Pi 3 at this time Here's the low-down on the GPS module:-165 dBm sensitivity, 10 Hz updates, 66 channelsOnly 20mA current drawBuilt in Real Time Clock (RTC) - slot in a CR1220 backup battery for 7-years or more of timekeeping even if the Raspberry Pi is off!PPS output on fix, by default connected to pin #4Internal patch antenna which works quite well when used outdoors + u.FL connector for external active antenna for when used indoors or in locations without a clear sky viewFix status LED blinks to let you know when the GPS has determined the current coordinatesWe spun up a HAT based on our Ultimate GPS, added a coin-cell holder for RTC usage, break-outs for all the Raspberry Pi's extra pins, and plenty of prototyping area for adding LEDs, sensors, and more. Please note, this HAT takes over the Raspberry Pi's hardware UART to send/receive data to and from the GPS module . So, if you need to use the RX/TX pins with a console cable, you cannot also use this HAT. Instead, you'll have to use a composite or HDMI monitor and keyboard to log in, or use ssh to connect over the network to your Pi. Read up on our tutorial for more information on how to use this fine HAT Comes as a fully assembled GPS + PCB and an additional 2x20 GPIO header. Some light soldering is required to attach the 2x20 GPIO header to the HAT but it's fast and easy for anyone with a soldering iron and solder.  You can also swap the plain female header we have with a 'stacky' type that lets you plug in a hat or GPIO cable on top  or a  slim ultra-low-profile header...
  • Adafruit Flex Cable for Raspberry Pi Camera - 1 meter...
    Precio:  $1,545.00

    Adafruit Flex Cable for Raspberry Pi Camera - 1 meter...

    -Titulo Original : Adafruit Flex Cable for Raspberry Pi Camera - 1 meter [ADA2143]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2143 // Stock Type: Raspberry Pi >> Cables >> Camera // In Stock & Ready to Ship // This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in.This cable is 1 meter long. We have cables in a ton of sizes  so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those in the shop as well) Please note, we did test this length cable with our Pi Model B/B+ and a Pi Camera and it worked great but 1 meter is really long for this kind of camera protocol, so if you have a very electrically noisy environment (inside a tesla coil?) you may have corrupted images...
  • Game Hat Para Raspberry Pi A+/b+/2b/3b/3b+ 3.5 Ips 480x320
    Precio:  $9,530.00

    Game Hat Para Raspberry Pi A+/b+/2b/3b/3b+ 3.5 Ips 480x320

    -Titulo Original : Waveshare Game HAT for Raspberry Pi A+/B+/2B/3B/3B+ 3.5inch IPS Screen 480x320 Resolution 60 Frame Experience Make Your Own Game Console-Fabricante : Waveshare-Descripcion Original: Este GAME HAT convertirá tu Raspberry Pi en una consola de juegos clásica en un segundo, te recuerda todos los placeres de los juegos en la memoria. Pantalla IPS de 3.5 pulgadas, resolución 480 × 320, experiencia de 60 cuadros, visualización fluida, no más pérdida de cuadros Compatible con Raspberry Pi A + / B + / 2B / 3B / 3B + (Raspberry Pi Zero / Zero W / Zero WH requiere otro cable HDMI) Integra el circuito de carga de la batería, alimentado por una batería de litio 18650 (NO incluida), se reproduce en cualquier lugar en cualquier momento Indicador de capacidad de la batería Altavoz a bordo y conector para auriculares, escuche el BGM familiar de los viejos tiempo...
  • Adafruit Ultimate GPS HAT for Raspberry Pi A+ or B+ Mini Kit
    Precio:  $6,034.00

    Adafruit Ultimate GPS HAT for Raspberry Pi A+ or B+ Mini Kit

    -Titulo Original : Adafruit Ultimate GPS HAT for Raspberry Pi A+ or B+ Mini Kit-Fabricante : ADAFRUIT-Descripcion Original: 165 dBm sensitivity, 10 Hz updates, 66 channels // Built in Real Time Clock (RTC) - slot in a CR1220 backup battery for 7-years or more of timekeeping even if the Raspberry Pi is off! // Internal patch antenna which works quite well when used outdoors + u.FL connector for external active antenna for when used indoors or in locations without a clear sky view // Fix status LED blinks to let you know when the GPS has determined the current coordinates // Raspberry Pi *not* included // This new HAT from Adafruit adds their celebrated Ultimate GPS on it, so you can add precision time and location to your Raspberry Pi Model A+ or B+ We spun up a HAT based on our Ultimate GPS, added a coin-cell holder for RTC usage, break-outs for all the Raspberry Pi's extra pins, and plenty of prototyping area for adding LEDs, sensors, and more. Please note, this HAT takes over the Raspberry Pi's hardware UART to send/receive data to and from the GPS module. So, if you need to use the RX/TX pins with a console cable, you cannot also use this HAT. Instead, you'll have to use a composite or HDMI monitor and keyboard to log in, or use ssh to connect over the network to your Pi. Read up on Adafruit's tutorial for more information on how to use this fine HAT. Comes as a fully assembled GPS + PCB and an additional 2x20 GPIO header. Some light soldering is required to attach the 2x20 GPIO header to the HAT but it's fast and easy for anyone with a soldering iron and solder. This HAT does not come with a 12mm coin battery! A CR1220 will let you use the real-time-clock capability of the GPS HAT...
  • Raspberry Pi Camera Module V2-8 Megapixel,1080p
    Precio:  $4,360.00

    Raspberry Pi Camera Module V2-8 Megapixel,1080p

    -Titulo Original : Raspberry Pi Camera Module V2-8 Megapixel,1080p-Fabricante : RASPBERRY PI-Descripcion Original: Second Generation Raspberry Pi Camera Module with Fixed Focus Lens // Sony Exmor IMX219 Sensor Capable of 4K30, 1080P60, 720P180, 8MP Still // 3280 (H) x 2464 (V) Active Pixel Count // Maximum of 1080P30 and 8MP Stills in Raspberry Pi Board // 2A Power Supply Highly Recommended // Color: The Raspberry Pi Camera V2 features the same, tiny footprint (25mm x 23mm x 9mm) as the original Pi Camera module, but features an upgraded Sony IMX219 image sensor which has a native resolution of 8 megapixels. The fixed-focus lens can capture 3280 x 2464 pixel images and 1080p30, 720p60 and 640x480p90 video. The Raspberry Pi Camera V2 connects to the CSi connector of your Raspberry Pi via a 15cm long flexible ribbon cable. It is plug-and-play compatible latest version of the Raspbian operating system making it perfect for time-lapse photography, recording video, motion detection, and security applications...
  • Adafruit Small-Size Perma-Proto Raspberry Pi Breadboard PCB.
    Precio:  $1,397.00

    Adafruit Small-Size Perma-Proto Raspberry Pi Breadboard PCB.

    -Titulo Original : Adafruit Small-Size Perma-Proto Raspberry Pi Breadboard PCB Kit [ADA1171]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1171 // Stock Type: Raspberry Pi >> Prototyping >> Model A+, B+, & Pi 2 // In Stock & Ready to Ship // We put a PermaProto quarter-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x13 pin header in and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake off and no labeling. Then we thought about how people actually prototype - usually starting with a solderless breadboard and then transferring the parts to a more permanent PCB. That's when we realized what people would really like is a proto board that makes it easy! This proto-board is the PCB you always wish you had, but never realized it! We took the basic layout of a quarter-sized breadboard (the PCB has 17 rows) and turned that into a beautiful PCB. The top side has a white silkscreen, and the same markings you're familiar with, to make transferring components easy. The bottom has a 4-hole pad design that matches a classic breadboard, with 4 power bus lines on the sides, and no mask so you can easily cut traces when necessary. We used 1.2mm diameter drill holes so even parts with big leads will fit. All holes are thru-plated for strength - these wont peel off with rework. The finish is a gold plate - you won't get oxidation like with bare copper perf ! There are also tons of mounting holes so you can attach the PCB to your project box. Comes with one PCB and one box header, you'll need to do a little light soldering to attach the box header to the PCB but its fast and easy to do. To connect it to a Pi, you'll also need a 26-pin GPIO cable if you don't already have one. Adafruit Small-Size Perma-Proto Raspberry Pi Breadboard PCB Kit ( 15:15 ...
  • Botones Y Joystick Quimat Diy Arcade Para Raspberry Pi, Kit De Controlador Happ Style Pi Arcade Que Incluye Placa De Cod
    Precio:  $4,424.00

    Botones Y Joystick Quimat Diy Arcade Para Raspberry Pi, Kit De Controlador Happ Style Pi Arcade Que Incluye Placa De Cod

    -Titulo Original : Quimat DIY Arcade Buttons and Joystick for Raspberry Pi,HAPP Style Pi Arcade Controller Kit Including Zero Delay USB Encoder Board,Micro Switch,Push Buttons and Joystick for Mame Jamma (Black)-Fabricante : Quimat-Descripcion Original: SoC: Actions S500;CPU:ARM Cortex-A9R4 Quad-Core up to1.1 GHz(ARM v7 instruction set) GPU: Imagination PowerVR SGX544, Support OpenGL-ES 1.1 and 2.0, OpenVG 1.0.1 // OS Support: Android 5.0 / Linux; RAM: 1 GB DDR3 SDRAM; Storage: 8GB eMMC; USB: 2 x USB2.0 HOST, MicroSD Card slot 1 x Micro USB3.0 HOST & DEVICE; Debug UART : used for developing debug // Ethernet: Port10/100Mbps; Wireless:Wi-Fi 802.11 b/g/n 2.4GHz; Bluetooth 4.0; 1 x IR receiver; Camera:1 x MIPI-CSI, 1 x Parallel 8-bit camera interface // Display:1 x HDMI 1.4(Type A - full), supports up to 1920*1080@60HZ 1 x LVDS-DSI for raw LCD panels(up to 1920 x 1080) Audio: HDMI output, Analog audio,I2S audio output (also available as audio input),On board MIC input // Expansion Interface:40 Pins Header: 28×GPIO, some of which can be used for specific functions including UART, I2C, SPI, PWM, I2S; SODIMM 204 Pins Connector : Standard DDR3 SODIMM 204P connector ,used for connect LeMaker Guitar core board // Actions S500 ARM Cortex-A9R4 Quad-Core up to1.1 GHz(ARM v7 instruction set) Imagination PowerVR SGX544 Android 5.0 / Linux 1 GB DDR3 SDRAM 8GB eMMC 2 x USB2.0 HOST, MicroSD Card slot;1 x Micro USB3.0 HOST & DEVICE used for developing debug 10/100Mbps; Wireless: Wi-Fi 802.11 b/g/n 2.4GHz; Bluetooth 4.0 12V-2A 88mm x 81.3mm 53g Lemaker Guitar demo board x1 Wiki: http://wiki.lemaker.org/LeMaker_Guitar Resource Download  http://www.lemaker.org/product-guitar-resource.html Download: http://forum.lemaker.org/forum.php?gid=146   firefly@ smartfire.cn   smartfire_cn firefly@ smartfire.c...
  • RASPBERRY - Box for Raspberry Pi RASPBERRY 10874
    Precio:  $2,777.00

    RASPBERRY - Box for Raspberry Pi RASPBERRY 10874

    -Titulo Original : RASPBERRY - Box for Raspberry Pi RASPBERRY 10874-Fabricante : RASPBERRY PI-Descripcion Original: Material: Plastic // Color: White/Red // Quantity: Single Pack // Made for Raspberry Pi 3 // Beautifully crafted, this red and white snap-together case is designed to protect your Raspberry Pi Model B. This 5-part enclosure has removable side panels to enable access to the GPIO...
  • Raspberry Pi Zero V1.3 Development Board - Camera Ready
    Precio:  $4,038.00

    Raspberry Pi Zero V1.3 Development Board - Camera Ready

    -Titulo Original : Raspberry Pi Zero v1.3 Development Board - Camera Ready-Fabricante : RASPBERRY PI-Descripcion Original: Unbelievably the super-small and super-affordable VERSION 1.3 WITH CAMERA ADAPTER! Raspberry Pi just got even smaller and even cheaper! Pi Zero is the heart of a Raspberry Pi on a tiny 65mm x 30mm board. With mini-HDMI, micro-B OTG USB, and the same 40-pin GPIO it has great connectivity. Pi Zero Features: BCM 2835 SOC @ 1GHz 1GHz 512MB of RAM micro-SD mini-HDMI micro-B USB for data micro-B USB for power Unpopulated 40-pin GPIO connector Compatible with existing HAT addons Dimensions: 65mm x 30mm x 5m...
  • Servo Package For The Gopigo And Raspberry Pi
    Precio:  $2,428.00

    Servo Package For The Gopigo And Raspberry Pi

    -Titulo Original : Servo Package for the GoPiGo and Raspberry Pi-Fabricante : RASPBERRY PI-Descripcion Original: Attaches directly to the GoPiGo and is controlled by software. // Mounting holes for the Raspberry Pi camera and the Ultrasonic sensor. // Servo can be controlled with the Raspberry PI. // The servo package for the GoPiGo comes with a servo and mounting hardware for attaching an Ultrasonic sensor or Raspberry Pi camera to the GoPiGo Raspberry Pi robot. The package comes with all mounting hardware needed to attach either the ultrasonic sensor or camera to your robot. The Raspberry Pi, Raspberry Pi Camera, and GoPiGo Robotics Kit are sold separately...
  • Official Raspberry Pi 3 Case - Red/White
    Precio:  $1,370.00

    Official Raspberry Pi 3 Case - Red/White

    -Titulo Original : Official Raspberry Pi 3 Case - Red/White-Fabricante : RASPBERRY PI-Descripcion Original: Official case for the Raspberry Pi from the Raspberry Pi Foundation // Removable Lid provides easy access to the camera and display ports // Removable Side Panels with easy access to the GPIO port // Removable Top Frame // Designed with Pi HAT's in mind // Color: The Official Case of the Raspberry Pi Foundation has been refreshed for the Pi 3. Designed with HATs in mind and featuring multiple removable panels. Enclose your board as much or as little as necessary to best suit your latest project...
  • Raspberry Pi Zero W (Wireless) ( 2017 model)
    Precio:  $5,795.00

    Raspberry Pi Zero W (Wireless) ( 2017 model)

    -Titulo Original : Raspberry Pi Zero W (Wireless) ( 2017 model)-Fabricante : RASPBERRY PI-Descripcion Original: Raspberry Pi Zero W // SoC: Broadcom BCM2835--CPU: ARM11 running at 1GHz--RAM: 512MB // Wireless: 2.4GHz 802.11n wireless LAN (WiFi) // Bluetooth: Bluetooth Classic 4.1 and Bluetooth LE // Dimensions: 65mm × 30mm × 5mm // Dimensions: 65mm × 30mm × 5mm SoC: Broadcom BCM2835 CPU: ARM11 running at 1GHz RAM: 512MB Wireless: 2.4GHz 802.11n wireless LAN Bluetooth: Bluetooth Classic 4.1 and Bluetooth LE Power: 5V, supplied via micro USB connector Video & Audio: 1080P HD video & stereo audio via mini-HDMI connector Storage: MicroSD card Output: Micro USB GPIO: 40-pin GPIO, unpopulated Pins: Run mode, unpopulated; RCA composite, unpopulated Camera Serial Interface (CSI...
  • Adafruit PiRTC - PCF8523 Real Time Clock for Raspberry Pi...
    Precio:  $1,692.00

    Adafruit PiRTC - PCF8523 Real Time Clock for Raspberry Pi...

    -Titulo Original : Adafruit PiRTC - PCF8523 Real Time Clock for Raspberry Pi [ADA3386]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 3386 // Stock Type: Breakout Boards >> Clocks // In Stock & Ready to Ship // This is a great battery-backed real time clock (RTC) that allows your Raspberry Pi project to keep track of time if the power is lost. Perfect for data-logging, clock-building, time-stamping, timers and alarms, etc. Equipped with  PCF8523  RTC, it works great with the Raspberry Pi and has native kernel support.Works perfectly with any Raspberry Pi (or similar single board linux computer) including the Pi 1, Pi 2, Pi 3, Pi Zero, A+, B+ etc.Fully assembled & tested PCB plugs directly into your Pi's GPIO pins - No soldering required! Will keep time for 5 years or more Note: This product does not come with a CR1220 coin cell battery.   We recommend you purchase a coin cell battery to use with this product. The PCF8523 is simple and inexpensive but not a high precision device. It may lose or gain a second or two per day. For a high-precision, temperature compensated alternative, please check out the DS3231 precision RTC . For setting up your Raspberry Pi to use the PiRTC, check out our detailed tutorial...
  • Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit
    Precio:  $4,148.00

    Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit

    -Titulo Original : Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit-Fabricante : ADAFRUIT-Descripcion Original: 4 H-Bridges: TB6612 chipset provides 1.2A per bridge with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC // Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) // Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping. // Big terminal block connectors to easily hook up wires (18-26AWG) and power // Works best with Raspberry Pi model A+, B+, or Pi 2, but can be used with a model A or B if you purchase a 2x13 extra-tall header and solder that instead of the 2x20 // Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Since the Raspberry Pi does not have a lot of PWM pins, we use a fully-dedicated PWM driver chip onboard to both control motor direction and speed. This chip handles all the motor and speed controls over I2C. Only two pins (SDA & SCL) are required to drive the multiple motors, and since it's I2C you can also connect any other I2C devices or HATs to the same pins. In fact, you can even stack multiple Motor HATs, up to 32 of them, for controlling up to 64 stepper motors or 128 DC motors (or a mix of the two) - just remember to purchase and solder in a stacking header instead of the one we include. Motors are controlled by TB6612 MOSFET drivers with 1.2A per channel current capability (you can draw up to 3A peak for approx 20ms at a time), a big improvement over L293D drivers and there are built-in flyback diodes as well. We even had a little space so we added a polarity protection FET on the power pins and a bit of prototyping area. And the HAT is assembled and tested here at Adafruit so all you have to do is solder on the included 2x20 plain header and the terminal blocks. Install the easy-to-use Python library, check out the examples and you're ready to go! Comes with an assembled & tested HAT, terminal blocks, and 2x20 plain header. Some soldering is required to assemble the headers o...
  • Set de 4 Joystick Arcade Mame Raspberry Pi / USB PC
    Precio:  $17,700.00

    Set de 4 Joystick Arcade Mame Raspberry Pi / USB PC

    -Titulo Original : 4 Player LED Arcade DIY Kit for USB MAME PC Game DIY & Raspberry Pi Retro Controller DIY Including 4X Arcade Joystick, 40x LED Chrome Arcade Buttons 2X Zero Delay USB Encoder-Fabricante : EG STARTS-Descripcion Original: Este es un juego de piezas de bricolaje LED para proyectos de bricolaje para 2 jugadores. ¡El codificador admite todos los sistemas de Windows! Todas las partes no son originales de Sanwa. Recién hecho en piezas de China, todos los botones no son de metal. Si el LED no se enciende. Luego, cambie la interfaz del LED de ubicación. ¡Cada codificador tiene su propio cable USB para asegurarse de que el modo multijugador puede jugar en las mismas condiciones! ¡El Joystick es un joystick profesional de 8 vías! Los botones son botones LED de 5V iluminados con microinterruptores incorporados en el interior. Los botones predeterminados están iluminados todo el tiempo. Si compra uno de este artículo, ¿Qué incluirá en el paquete? Codificador USB 4x Zero Delay LED 4x cable USB 4x cables de 5 pines para Joystick 40x cables de 3 pines para botones LED Joystick 4x 5 pines de 8 vías (1x rojo, 1x amarillo, 1x azul, 1x verde) 1x 1 jugador más grande 5V LED cromo pulsadores (blanco) con lámpara LED y micro interruptor 1x 2 jugadores más grandes 5V LED botones de cromo (blanco) con lámpara LED y micro interruptor 1x 3 jugadores más grandes botones de cromo LED de 5V (blanco) con lámpara LED y micro interruptor 1x 4 jugadores más grandes 5V LED botones de cromo (blanco) con lámpara LED y micro interruptor 4x Coin Botones de cromo LED de 5V más grandes (blanco) con lámpara LED y micro interruptor 32x botones LED cromados de 5V más grandes con LED y micro interruptor (8x rojo, 8x amarillo, 8x azul, 8x verde) 1x instrucciones Consejos para la instalación. 1. Por favor lea nuestro manual de usuario antes de comenzar sus acciones de bricolaje. 2. ¡Es muy importante! Conecte el cable de 5 pines del Joystick a la ranura de 5 pines que se encuentra frente al terminal USB-B. Mucha gente conecta el joystick a la ranura incorrecta de 5 pines. 3. No es necesario separar las funciones del botón cuando conectas el cable a los botones y al panel de codificador, excepto que deseas agregar las funciones Auto-Fire, Tubro, Clear y Mode. Todas las funciones del botón de lucha pueden ser establecido en MAME o RetroPie. Las funciones Auto-Fire, Tubro, Clear y Mode tienen su propia ranura en la placa del codificador. 4. Para jugadores profesionales. Sugerimos que cambie todos los botones y joysticks a SANWA Brand o SEIMITSU Brand. Consejos para nuevos usuarios: 1. El artículo necesita trabajar con el emulador MAME. Entonces, antes de construir su propio proyecto, descargue uno para trabajar con las piezas. 2. Si usa este kit para construir sus propios proyectos de frambuesa Pi Retropie. Busque los pasos antes de su bricolaje...
  • Raspberry Pi PWM Servo Hat Development Board
    Precio:  $2,603.00

    Raspberry Pi PWM Servo Hat Development Board

    -Titulo Original : 2327 - Raspberry Pi PWM Servo Hat Development Board-Fabricante : ADAFRUIT-Descripcion Original: The Adafruit 16-Channel 12-bit PWM/Servo HAT will drive up to 16 servos or PWM outputs over I2C with only 2 pins. The on-board PWM controller will drive all 16 channels simultaneously with no additional Raspberry Pi processing overhead. What's more, you can stack up to 62 of them to control up to 992 servos - all with the same 2 pins! // It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running. // For use with Raspberry Pi Model A+ or B+, can be used with the Model A or B if you use a tall 2x13 header instead of the included 2x20. // Please note! This kit does not come with Raspberry Pi, servos, or required 5V power supply. // The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy HAT! It adds the capability to control 16 Servos with perfect timing. It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running. For use with Raspberry Pi Model A+ or B+, can be used with the Model A or B if you use a tall 2x13 header instead of the included 2x20. The Adafruit 16-Channel 12-bit PWM/Servo HAT will drive up to 16 servos or PWM outputs over I2C with only 2 pins. The on-board PWM controller will drive all 16 channels simultaneously with no additional Raspberry Pi processing overhead. What's more, you can stack up to 62 of them to control up to 992 servos - all with the same 2 pins! Best of all, we even have a Python library you can use, so you'll be up and running instantly, to make your robotic creation com to life. The Adafruit PWM/Servo HAT is the perfect solution for any project that requires a lot of servos or PWM outputs! Each order comes with a Servo HAT, a 2-pin terminal block, four 3x4 headers and a 2x20 socket header. You'll need to do some light through-hole soldering to attach the headers onto the HAT circuit board, but its easy to do with basic soldering tools like a soldering iron and rosin core electronics solder. If you would like to stack multiple HATs onto one Pi, you can also pick up a 2x20 stacking header and a set of right-angle 3x4 headers that should be soldered on instead. Please note! This kit does not come with Raspberry Pi, servos, or required 5V power supply...
  • Adafruit Raspberry Pi B+ Case - Smoke Base w/ Clear Top
    Precio:  $1,848.00

    Adafruit Raspberry Pi B+ Case - Smoke Base w/ Clear Top

    -Titulo Original : Adafruit Raspberry Pi B+ Case - Smoke Base w/ Clear Top-Fabricante : ADAFRUIT-Descripcion Original: The Pi snaps into the base and the lid fits snugly onto the top. If you want to break out your Pi you can use your case without the lid and add hats to your B+ with ease. // This case works for the Raspberry Pi Model B+ only. // It does work with the model A+ but there will be a bit of empty space of course, and you'll need to snake your USB cable or connector through the front holes which may not work if the cable is bulky // It does not work for the Raspberry Pi Model A or B. // No Pi, cables, or Pi Camera included. This product is just the case! // This enclosure was designed by Mike Doell - just like our elegant, beautiful, and functional Pi Case for Raspberry Pi Model B. Made of ultra-durable, super-glossy polycarbonate, it is both good looking and tough enough to toss into your bookbag or toolbox. It has slim openings for all your cables, an easy-to-remove beveled slot for your Micro SD card, slots for both your Pi Camera and upcoming Display, and a space for your GPIO cable to extend out from the Pi. The Pi snaps into the base and the lid fits snugly onto the top. If you want to break out your Pi you can use your case without the lid and add hats to your B+ with ease. This is the basic, classic enclosure with a smoke base and a clear top. More colors are coming soon and we'll have packs to mix and match for ultimate Raspberry Pi B+ enclosure fun, but we'll be starting out with this very neutral gray/clear combo. This case works for the Raspberry Pi Model B+ only. It does not work for the Raspberry Pi Model A or B. It does work with the model A+ but there will be a bit of empty space of course, and you'll need to snake your USB cable or connector through the front holes which may not work if the cable is bulky No Pi, cables, or Pi Camera included. This product is just the case...
  • Raspberry Pi 16GB Preloaded (Noobs) SD Card …
    Precio:  $2,419.00

    Raspberry Pi 16GB Preloaded (Noobs) SD Card …

    -Titulo Original : Raspberry Pi 16GB Preloaded (Noobs) SD Card …-Fabricante : RASPBERRY PI-Descripcion Original: Genuine 16GB SanDisk Ultra Class 10 MicroSD Card (Red/White) with adapter // Works with all Raspberry Pi Models // Fully Qualified by the Raspberry Pi Foundation for Optimum Performance // Preloaded with the NOOBS Operating System // Raspberry Pi 16GB Preloaded (NOOBS) SD Card &hellip...
  • ContempoViews Intermediate Starter Kit para Raspberry Pi B + 2 & 3 RPi Learning Kit 1210
    Precio:  $5,114.00

    ContempoViews Intermediate Starter Kit para Raspberry Pi B + 2 & 3 RPi Learning Kit 1210

    -Titulo Original : ContempoViews Intermediate Starter Kit for Raspberry Pi B+ 2 & 3 RPi Learning Kit 1210-Fabricante : Contempo Views-Descripcion Original: Advanced learning kit intended for those with some experience with RPi or Arduino // Over 35 different components // Nearly 100pcs in total // Numerous electronic components to enhance your Raspberry Pi experience // This is an advanced learning kit for Raspberry Pi. It is equipped with more interesting and powerful functional modules than the basic starter kit, and so it is more suitable for those who have already had some relevant knowledge. This advanced version provides more abundant learning materials and more space for creating some interesting interactive projects. Raspberry Pi is a credit card sized single-board computer, through which we can learn relevant knowledge about Linux operating systems as well as C and python language based on Raspberry Pi debian (based on linux) system, not to mention sensor/module applications on Raspberry Pi. Arduino and Raspberry Pi are a great match for each other. - 10MM Full color high-brightness sensor x 1 - Home appliances control module x 1 - Raspberry Pi GPIO V2 shield x 1 - High-quality 830 hole breadboard x 1 - MAX7219 dot matrix module x 1 - 9g servo x 1 - ULN2003 driving board x 1 - Black remote control x 1 - 5V step motor x 1 - 50K adjustable potentiometer x 1 - 801S vibration sensor x 1 - PS2 game rocker module x 1 - Four-bit digital tube x 1 - One-bit digital tube x 1 - 74H595 IC x 1 - Red LED x 5 - Blue LED x 5 - Yellow LED x 5 - 1K resistor x 5 - 10K resistor x 5 - 220R resistor x 8 - DHT11 Humiture sensor x 1 - DS3231 clock x 1 - PCF8591 AD/DA conversion module x1 - Yellow button cap x 4 - Infrared receiver component x 1 - LM35 component x 1 - Flame component x 1 - Ball component x 2 - Light-sensitive component x 3 - Mini LCD screen x 1 - 40Pin colorful flat cable x 1 - Membrane keypad x 1 - Dupont Cable x 30 - Male to female dupont cable/20-row x 1 - SR04 ultrasonic x ...
  • PiTFT Plus 2.8in Resistive Touchscreen Raspberry Pi 2298
    Precio:  $6,375.00

    PiTFT Plus 2.8in Resistive Touchscreen Raspberry Pi 2298

    -Titulo Original : 2298 - PiTFT Plus 2.8in Resistive Touchscreen for Raspberry Pi-Fabricante : ADAFRUIT-Descripcion Original: This PiTFT 2.8" fits perfectly onto the Pi Model A+, B+, or Pi 2! // The display comes fully assembled and includes 4 tactile switches soldered on. // This display has all 40 pins GPIO pins brought out so you can connect a 40-pin GPIO cable underneath. // Features a 2.8" display with 320x240 16-bit color pixels and a resistive touch overlay. // Raspberry Pi computer and enclosure not included! // This display features a 2.8 display with 320x240 16-bit color pixels and a resistive touch overlay. The plate uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top! This updated design fits perfectly onto the Pi Model A+, B+, or Pi 2! This display has all 40 pins GPIO pins brought out so you can connect a 40-pin GPIO cable underneath. The display and touchscreen uses the hardware SPI pins (SCK, MOSI, MISO, CE0, CE1) as well as GPIO #25 and #24. All other GPIO are unused. Since we had a tiny bit of space, there's 4 slim tactile switches wired to four GPIOs, that you can use if you want to make a basic user interface. For example, you can use one as a power on/off button. See below for the link to get the optional tact switches, they're not included. Use it for console access or easily pop up X11 onto the PiTFT for a mini monitor, although its rather small at 320x240. Instead, we recommend using PyGame or other SDL-drawing programs to write onto the frame buffer. Raspberry Pi computer and enclosure not included! The display comes fully assembled and includes 4 tactile switches soldered on...
Mostrar del 1 al 24 (de 52 productos)
Páginas de Resultados:  1  2  3  [Siguiente >>]