Arriba

Componentes Electrónicos > Raspberry Pi

Mostrar: 
Mostrar del 1 al 24 (de 41 productos)
Páginas de Resultados:  1  2  [Siguiente >>] 
  • Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit
    Precio:  $3,739.00

    Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit

    -Titulo Original : Adafruit DC & Stepper Motor HAT for Raspberry Pi - Mini Kit-Fabricante : ADAFRUIT-Descripcion Original: 4 H-Bridges: TB6612 chipset provides 1.2A per bridge with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC // Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution) // Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping. // Big terminal block connectors to easily hook up wires (18-26AWG) and power // Works best with Raspberry Pi model A+, B+, or Pi 2, but can be used with a model A or B if you purchase a 2x13 extra-tall header and solder that instead of the 2x20 // Let your robotic dreams come true with the new DC+Stepper Motor HAT from Adafruit. This Raspberry Pi add-on is perfect for any motion project as it can drive up to 4 DC or 2 Stepper motors with full PWM speed control. Since the Raspberry Pi does not have a lot of PWM pins, we use a fully-dedicated PWM driver chip onboard to both control motor direction and speed. This chip handles all the motor and speed controls over I2C. Only two pins (SDA & SCL) are required to drive the multiple motors, and since it's I2C you can also connect any other I2C devices or HATs to the same pins. In fact, you can even stack multiple Motor HATs, up to 32 of them, for controlling up to 64 stepper motors or 128 DC motors (or a mix of the two) - just remember to purchase and solder in a stacking header instead of the one we include. Motors are controlled by TB6612 MOSFET drivers with 1.2A per channel current capability (you can draw up to 3A peak for approx 20ms at a time), a big improvement over L293D drivers and there are built-in flyback diodes as well. We even had a little space so we added a polarity protection FET on the power pins and a bit of prototyping area. And the HAT is assembled and tested here at Adafruit so all you have to do is solder on the included 2x20 plain header and the terminal blocks. Install the easy-to-use Python library, check out the examples and you're ready to go! Comes with an assembled & tested HAT, terminal blocks, and 2x20 plain header. Some soldering is required to assemble the headers o...
  • Adafruit Ultimate GPS HAT for Raspberry Pi A+ or B+ Mini Kit
    Precio:  $9,499.00

    Adafruit Ultimate GPS HAT for Raspberry Pi A+ or B+ Mini Kit

    -Titulo Original : Adafruit Ultimate GPS HAT for Raspberry Pi A+ or B+ Mini Kit-Fabricante : ADAFRUIT-Descripcion Original: 165 dBm sensitivity, 10 Hz updates, 66 channels // Built in Real Time Clock (RTC) - slot in a CR1220 backup battery for 7-years or more of timekeeping even if the Raspberry Pi is off! // Internal patch antenna which works quite well when used outdoors + u.FL connector for external active antenna for when used indoors or in locations without a clear sky view // Fix status LED blinks to let you know when the GPS has determined the current coordinates // Raspberry Pi *not* included // This new HAT from Adafruit adds their celebrated Ultimate GPS on it, so you can add precision time and location to your Raspberry Pi Model A+ or B+ We spun up a HAT based on our Ultimate GPS, added a coin-cell holder for RTC usage, break-outs for all the Raspberry Pi's extra pins, and plenty of prototyping area for adding LEDs, sensors, and more. Please note, this HAT takes over the Raspberry Pi's hardware UART to send/receive data to and from the GPS module. So, if you need to use the RX/TX pins with a console cable, you cannot also use this HAT. Instead, you'll have to use a composite or HDMI monitor and keyboard to log in, or use ssh to connect over the network to your Pi. Read up on Adafruit's tutorial for more information on how to use this fine HAT. Comes as a fully assembled GPS + PCB and an additional 2x20 GPIO header. Some light soldering is required to attach the 2x20 GPIO header to the HAT but it's fast and easy for anyone with a soldering iron and solder. This HAT does not come with a 12mm coin battery! A CR1220 will let you use the real-time-clock capability of the GPS HAT...
  • Raspberry Pi 32gb Preloaded (noobs) Sd Card
    Precio:  $2,959.00

    Raspberry Pi 32gb Preloaded (noobs) Sd Card

    -Titulo Original : Raspberry Pi 32GB Preloaded (NOOBS) SD Card-Fabricante : RASPBERRY PI-Descripcion Original: Official 32GB MicroSD Card and Full-Size Adapter // Fully Qualified by the Raspberry Pi Foundation for Optimum Performance // Preloaded with the NOOBS Operating System // Works with all Raspberry Pi Models // Raspberry Pi Foundation Official 32GB MicroSD Card with Full-Size Adapter. Fully Qualified by the Raspberry Pi Foundation for Optimum Performance. Preloaded with the NOOBS Operating System. Works with all Raspberry Pi Models. SanDisk Ultra Class 10 MicroSD Card in OEM (black color) packaging...
  • Adafruit Aluminum Heat Sink for Raspberry Pi 3 - 14 x 14 x..
    Precio:  $919.00

    Adafruit Aluminum Heat Sink for Raspberry Pi 3 - 14 x 14 x..

    -Titulo Original : Adafruit Aluminum Heat Sink for Raspberry Pi 3 - 14 x 14 x 8mm [ADA3083]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 3083 // Stock Type: Components & Parts >> Heat Sinks // In Stock & Ready to Ship // Looking for a nice way to cool down your   Raspberry Pi 3 ? Check out this   This heat sink is made from high quality aluminum and will work perfectly with any   Raspberry Pi   but is best paired with a Raspberry Pi 3 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy. Clean the surface of the chip of any dust or grease then peel off the protective film and press the heat sink firmly onto the chip. You can use this heatsink with any of our   injection molded Adafruit Pi Enclosures , but it may not work with other enclosures and most HATs will not fit on top with the heat sink installed.We don't have formal specs for this heat sink, but when we ran 'stress -c 4' on the Pi 3 to run all 4 CPUs, a heat-sink-less Pi quickly dropped down to 0.96 GHz to maintain thermal equilibrium. With this heat sink installed, it could run at 1.1 GHz (so, approx 14% higher performance)Note that you do not   need   a heatsink for the Pi 3, it will automatically adjust its speed to avoid overheating! It can also, of course, be used for other processors and chips...
  • Adafruit Flex Cable for Raspberry Pi Camera - 300mm / 12...
    Precio:  $1,699.00

    Adafruit Flex Cable for Raspberry Pi Camera - 300mm / 12...

    -Titulo Original : Adafruit Flex Cable for Raspberry Pi Camera - 300mm / 12 [ADA1648]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1648 // Stock Type: Raspberry Pi >> Cables >> Camera // In Stock & Ready to Ship // This cable will let you swap out the stock 150mm long flex cable from a Raspberry Pi Camera (either 'classic' or 'NoIR' type) for a different size. Works great, just carefully open the connector on the Pi and slip this one in. This cable is 300mm long We have cables in 50mm, 100mm, 200mm and 300mm so you can have the perfect fit. Each order comes with one cable, Pi Camera not included (but we have those in the shop as well) Flex Cable for Raspberry Pi Camera - 300mm / 12 ( 7:45 ...
  • Raspberry Pi 3 A+ Computer Board
    Precio:  $5,559.00

    Raspberry Pi 3 A+ Computer Board

    -Titulo Original : Raspberry Pi 3 A+ Computer Board-Fabricante : RASPBERRY-Descripcion Original: Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC @ 1.4GHz // 512MB LPDDR2 SDRAM // 2.4GHz and 5GHz IEEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2/BLE // Extended 40-pin GPIO header // Full-size HDMI // 1.4GHz 64-bit quad-core processor, dual-band wireless LAN, Bluetooth 4.2/BLE in the same mechanical format as the Raspberry Pi 1 Model A...
  • Official Raspberry Pi 3 Case - Red/White
    Precio:  $1,709.00

    Official Raspberry Pi 3 Case - Red/White

    -Titulo Original : Official Raspberry Pi 3 Case - Red/White-Fabricante : RASPBERRY PI-Descripcion Original: Official case for the Raspberry Pi from the Raspberry Pi Foundation // Removable Lid provides easy access to the camera and display ports // Removable Side Panels with easy access to the GPIO port // Removable Top Frame // Designed with Pi HAT's in mind // Color: The Official Case of the Raspberry Pi Foundation has been refreshed for the Pi 3. Designed with HATs in mind and featuring multiple removable panels. Enclose your board as much or as little as necessary to best suit your latest project...
  • ContempoViews Intermediate Starter Kit para Raspberry Pi B + 2 & 3 RPi Learning Kit 1210
    Precio:  $4,849.00

    ContempoViews Intermediate Starter Kit para Raspberry Pi B + 2 & 3 RPi Learning Kit 1210

    -Titulo Original : ContempoViews Intermediate Starter Kit for Raspberry Pi B+ 2 & 3 RPi Learning Kit 1210-Fabricante : Contempo Views-Descripcion Original: Advanced learning kit intended for those with some experience with RPi or Arduino // Over 35 different components // Nearly 100pcs in total // Numerous electronic components to enhance your Raspberry Pi experience // This is an advanced learning kit for Raspberry Pi. It is equipped with more interesting and powerful functional modules than the basic starter kit, and so it is more suitable for those who have already had some relevant knowledge. This advanced version provides more abundant learning materials and more space for creating some interesting interactive projects. Raspberry Pi is a credit card sized single-board computer, through which we can learn relevant knowledge about Linux operating systems as well as C and python language based on Raspberry Pi debian (based on linux) system, not to mention sensor/module applications on Raspberry Pi. Arduino and Raspberry Pi are a great match for each other. - 10MM Full color high-brightness sensor x 1 - Home appliances control module x 1 - Raspberry Pi GPIO V2 shield x 1 - High-quality 830 hole breadboard x 1 - MAX7219 dot matrix module x 1 - 9g servo x 1 - ULN2003 driving board x 1 - Black remote control x 1 - 5V step motor x 1 - 50K adjustable potentiometer x 1 - 801S vibration sensor x 1 - PS2 game rocker module x 1 - Four-bit digital tube x 1 - One-bit digital tube x 1 - 74H595 IC x 1 - Red LED x 5 - Blue LED x 5 - Yellow LED x 5 - 1K resistor x 5 - 10K resistor x 5 - 220R resistor x 8 - DHT11 Humiture sensor x 1 - DS3231 clock x 1 - PCF8591 AD/DA conversion module x1 - Yellow button cap x 4 - Infrared receiver component x 1 - LM35 component x 1 - Flame component x 1 - Ball component x 2 - Light-sensitive component x 3 - Mini LCD screen x 1 - 40Pin colorful flat cable x 1 - Membrane keypad x 1 - Dupont Cable x 30 - Male to female dupont cable/20-row x 1 - SR04 ultrasonic x ...
  • PiTFT Plus 3.2in Touchscreen for Raspberry Pi
    Precio:  $7,189.00

    PiTFT Plus 3.2in Touchscreen for Raspberry Pi

    -Titulo Original : 2616 - PiTFT Plus 3.2in Touchscreen for Raspberry Pi-Fabricante : ADAFRUIT-Descripcion Original: Touch screen for Raspberry Pi // Comes fully assembled // Great example code at Adafruit // Easy to use // Raspberry Pi _not_ included // This dipslay features a 3.2 display with 320x240 16-bit color pixels and a resistive touch overlay. The plate uses the high speed SPI interface on the Pi and can use the mini display as a console, X window port, displaying images or video etc. Best of all it plugs right in on top! This display is functionally the same as our classic PiTFT 2.8 and PiTFT Plus 2.8 - same pins used, same resolution, same drivers, but is just a bit bigger. It also has a 26- pins GPIO pins brought out so you can connect a 26-pin Raspberry Pi GPIO cable underneath. It's the same outline as a Pi 2/B+ it fits well on top of a Pi in our Raspberry Pi Enclosure base. The display and touchscreen uses the hardware SPI pins (SCK, MOSI, MISO, CE0, CE1) as well as GPIO #25 and #24. All other GPIO are unused. Since we had a tiny bit of space, there's 4 spots for optional slim tactile switches wired to four GPIOs, that you can use if you want to make a basic user interface. For example, you can use one as a power on/off button. See below for the link to get the optional tact switches, they're not included. Use it for console access or easily pop up X11 onto the PiTFT for a mini monitor, although its rather small at 320x240. Instead, we recommend using PyGame or other SDL-drawing programs to write onto the frame buffer. Raspberry Pi computer and enclosure not included! This display comes fully assembled, just plug it onto your Raspberry Pi and install our software to rock out. Check out our detailed tutorial on how to play videos, display images, and otherwise customize your PiTFT (the tutorial is identical to the 2.8 PiTFT...
  • Adafruit RGB Matrix HAT + RTC for Raspberry Pi - Mini Kit
    Precio:  $3,669.00

    Adafruit RGB Matrix HAT + RTC for Raspberry Pi - Mini Kit

    -Titulo Original : Adafruit RGB Matrix HAT + RTC for Raspberry Pi - Mini Kit-Fabricante : ADAFRUIT-Descripcion Original: Simple design - plug in power, plug in IDC cable, and run Adafruit's Python code. // Onboard level shifters to convert the RasPi's 3.3V to 5.0V logic for clean matrix driving. // Works with Adafruit 16x32, 32x32 or 32x64 RGB LED Matrices with HUB75 connections. You can even chain multiple matrices together for a longer display. // Included: RGB Matrix HAT controller. NOT Included: RGB LED Matrix (sold separately), Raspberry Pi, 5V power supply, or coin cell battery for Real Time Clock. (Real Time Clock not needed for unit to function) // You can now create a dazzling display with your Raspberry Pi Model A+/B+/Pi 2 or Pi 3 with the Adafruit RGB Matrix HAT. This HAT plugs into your Pi and makes it super easy to control RGB matrices such as those we stock in the shop and create a colorful scrolling display or mini LED wall with ease. Each order comes with a HAT PCB with all surface mount parts assembled, a 2x20 female socket connector, a 2 pin terminal block, and a 2x8 IDC socket connector. A CR1220 coin cell is not included (required for real time clock). A 5V power supply is also required, not included, for powering the matrix itself. The Pi cannot do it due to the high currents. To calculate the max current of your matrix set up, multiply the width of all the chained matrix by 0.12 : A 32 pixel wide matrix needs 32*0.12 = 3.85A so pick up a 5V 4A power supply...
  • Raspberry Pi 7 Touchscreen Display
    Precio:  $12,979.00

    Raspberry Pi 7 Touchscreen Display

    -Titulo Original : Raspberry Pi 7 Touchscreen Display-Fabricante : RASPBERRY PI-Descripcion Original: Brand New in box. The product ships with all relevant accessories // Brand New in box. The product ships with all relevant accessorie...
  • RASPBERRY PI-SENSEHAT Raspberry Pi Sense HAT...
    Precio:  $5,979.00

    RASPBERRY PI-SENSEHAT Raspberry Pi Sense HAT...

    -Titulo Original : RASPBERRY-PI RASPBERRYPI-SENSEHAT Raspberry Pi Sense HAT with Orientation, Pressure, Humidity and Temperature Sensors-Fabricante : RASPBERRY PI-Descripcion Original: Price For: EachOrder Unit: Each 1 Core Architecture:: AVR Core Sub-Architecture:: - Features:: 8×8 LED Matrix Display, Accelero/Gyro/Magneto/Air Pressure/Temp/Humidity I2C Sensors, Teeny Joystick For Use With:: Raspberry Pi Single Board Computers Kit Contents:: Add-on Board ATtiny88 SVHC:: To Be Advised Silicon Core Number:: ATtiny88 Silicon Family Name:: ATtiny // Silicon Manufacturer:: Atmel // RASPBERRY-PI RASPBERRYPI-SENSEHAT Raspberry Pi Sense HAT with Orientation, Pressure, Humidity and Temperature Sensor...
  • Game Hat Para Raspberry Pi A+/b+/2b/3b/3b+ 3.5 Ips 480x320
    Precio:  $9,979.00

    Game Hat Para Raspberry Pi A+/b+/2b/3b/3b+ 3.5 Ips 480x320

    -Titulo Original : Waveshare Game HAT for Raspberry Pi A+/B+/2B/3B/3B+ 3.5inch IPS Screen 480x320 Resolution 60 Frame Experience Make Your Own Game Console-Fabricante : Waveshare-Descripcion Original: Este GAME HAT convertirá tu Raspberry Pi en una consola de juegos clásica en un segundo, te recuerda todos los placeres de los juegos en la memoria. Pantalla IPS de 3.5 pulgadas, resolución 480 × 320, experiencia de 60 cuadros, visualización fluida, no más pérdida de cuadros Compatible con Raspberry Pi A + / B + / 2B / 3B / 3B + (Raspberry Pi Zero / Zero W / Zero WH requiere otro cable HDMI) Integra el circuito de carga de la batería, alimentado por una batería de litio 18650 (NO incluida), se reproduce en cualquier lugar en cualquier momento Indicador de capacidad de la batería Altavoz a bordo y conector para auriculares, escuche el BGM familiar de los viejos tiempo...
  • Raspberry Pi Sense HAT - AstroPi
    Precio:  $7,989.00

    Raspberry Pi Sense HAT - AstroPi

    -Titulo Original : 2483095 - Raspberry Pi Sense HAT - AstroPi-Fabricante : RASPBERRY PI-Descripcion Original: Works With All Raspberry PI boards // Accelerometer , Gyroscope , Thermometer // Humidity & Pressure Sensor All in One! // If you own a Raspberry Pi 1, 2 or a 3, you need this add-on! This fantastic shield has so much packed into such a small foot print. No need for external power input, as the shield pulls power from the Pi its self. Not only do you get an amazingly bright programmable 8x8 RGB matrix but you also get: -Accelerometer. -Gyroscope. -Magnetometer. -Pressure sensor. -Thermometer. -Humidity sensor. -Small multi-directional joystick. Product condition: Ne...
  • Raspberry Pi Zero V1.3 Development Board - Camera Ready
    Precio:  $3,989.00

    Raspberry Pi Zero V1.3 Development Board - Camera Ready

    -Titulo Original : Raspberry Pi Zero v1.3 Development Board - Camera Ready-Fabricante : RASPBERRY PI-Descripcion Original: Unbelievably the super-small and super-affordable VERSION 1.3 WITH CAMERA ADAPTER! Raspberry Pi just got even smaller and even cheaper! Pi Zero is the heart of a Raspberry Pi on a tiny 65mm x 30mm board. With mini-HDMI, micro-B OTG USB, and the same 40-pin GPIO it has great connectivity. Pi Zero Features: BCM 2835 SOC @ 1GHz 1GHz 512MB of RAM micro-SD mini-HDMI micro-B USB for data micro-B USB for power Unpopulated 40-pin GPIO connector Compatible with existing HAT addons Dimensions: 65mm x 30mm x 5m...
  • Raspberry Pi 1 A+ 512mb (2016 Model)
    Precio:  $3,749.00

    Raspberry Pi 1 A+ 512mb (2016 Model)

    -Titulo Original : Raspberry Pi 1 A+ 512MB (2016 Model)-Fabricante : RASPBERRY PI-Descripcion Original: USB: One USB 2.0 Port // Video Output: HDMI and Composite // Sound: L/R Stereo (via 3.5mm 4 Pole Cable) // Memory: 512MB Ram // Operating System: Uses microSD card slot to load O/S // The Raspberry Pi A+ features a smaller form-factor and an upgraded 512MB of RAM making it perfect when you need power and space efficiency. Otherwise it's the same capable little computer we've come to know and love. The Raspberry Pi A+ based around a Broadcom BCM2835 SoC, which includes an ARM1176JZF-S 700 MHz processor, VideoCore IV GPU, and an upgraded 512 Megabytes of RAM. This revision A+ board features four mounting holes for easy installation, a built-in reset circuit, and can be powered via the USB data ports. The design does not include a built-in hard disk or solid-state drive, instead relying on an microSD card for booting and long-term storage. This board is intended to run Linux kernel based operating systems. The Raspberry Pi uses Linux-kernel based operating systems. The Raspberry Pi does not come with a real-time clock, so an OS must use a network time server, or ask the user for time information at boot time to get access to time and date info for file time and date stamping. However a real time clock (such as the DS1307) with battery backup can be easily added via the I2C interface. Board SpecificationsProcessor: ARM 700Mhz CP...
  • Raspberry Pi 3 Model B Board
    Precio:  $6,889.00

    Raspberry Pi 3 Model B Board

    -Titulo Original : Raspberry Pi 3 Model B Board-Fabricante : RASPBERRY PI-Descripcion Original: Raspberry pi 3 model b adds wireless LAN and Bluetooth connectivity making it the ideal solution for powerful connected designs. // Raspberry pi 3 use Processor chipest Boardcom BCM 2837 64 bIT ARMv7 Quad Core processor powered Singel Board Computer running at 1200MHz // Raspberry pi 3 model b RAM : 1GB SDRAM@400MHz //...
  • Adafruit Aluminum Heat Sink for Raspberry Pi 3 - 15 x 15 x..
    Precio:  $1,089.00

    Adafruit Aluminum Heat Sink for Raspberry Pi 3 - 15 x 15 x..

    -Titulo Original : Adafruit Aluminum Heat Sink for Raspberry Pi 3 - 15 x 15 x 15mm [ADA3082]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 3082 // Stock Type: Components & Parts >> Heat Sinks // In Stock & Ready to Ship // Looking for the best heat sink for your Raspberry Pi 3 ? Check out this nice and tall This heat sink is made from high quality aluminum and will work perfectly with any Raspberry Pi   but is best paired with a Raspberry Pi 3 since it can run a little hot. It comes with thermal adhesive already applied to the back making installation super easy. Clean the surface of the chip of any dust or grease then peel off the protective film and press the heat sink firmly onto the chip. You can use this heatsink with any of our injection molded Adafruit Pi Enclosures , but it may not work with other enclosures and most HATs will not fit on top with the heat sink installed.We don't have formal specs for this heat sink, but when we ran 'stress -c 4' on the Pi 3 to run all 4 CPUs, a heat-sink-less Pi quickly dropped down to 0.96 GHz to maintain thermal equilibrium. With this heat sink installed, it could run at 1.16GHz (so, 20% higher performance)Note that you do not need a heatsink for the Pi 3, it will automatically adjust its speed to avoid overheating! It can also, of course, be used for other processors and chips...
  • RASPBERRY - Box for Raspberry Pi RASPBERRY 10874
    Precio:  $2,869.00

    RASPBERRY - Box for Raspberry Pi RASPBERRY 10874

    -Titulo Original : RASPBERRY - Box for Raspberry Pi RASPBERRY 10874-Fabricante : RASPBERRY PI-Descripcion Original: Material: Plastic // Color: White/Red // Quantity: Single Pack // Made for Raspberry Pi 3 // Beautifully crafted, this red and white snap-together case is designed to protect your Raspberry Pi Model B. This 5-part enclosure has removable side panels to enable access to the GPIO...
  • Raspberry Pi PWM Servo Hat Development Board
    Precio:  $2,709.00

    Raspberry Pi PWM Servo Hat Development Board

    -Titulo Original : 2327 - Raspberry Pi PWM Servo Hat Development Board-Fabricante : ADAFRUIT-Descripcion Original: The Adafruit 16-Channel 12-bit PWM/Servo HAT will drive up to 16 servos or PWM outputs over I2C with only 2 pins. The on-board PWM controller will drive all 16 channels simultaneously with no additional Raspberry Pi processing overhead. What's more, you can stack up to 62 of them to control up to 992 servos - all with the same 2 pins! // It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running. // For use with Raspberry Pi Model A+ or B+, can be used with the Model A or B if you use a tall 2x13 header instead of the included 2x20. // Please note! This kit does not come with Raspberry Pi, servos, or required 5V power supply. // The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these signals, pop on this handy HAT! It adds the capability to control 16 Servos with perfect timing. It can also do PWM up to 1.6 KHz with 12 bit precision, all completely free-running. For use with Raspberry Pi Model A+ or B+, can be used with the Model A or B if you use a tall 2x13 header instead of the included 2x20. The Adafruit 16-Channel 12-bit PWM/Servo HAT will drive up to 16 servos or PWM outputs over I2C with only 2 pins. The on-board PWM controller will drive all 16 channels simultaneously with no additional Raspberry Pi processing overhead. What's more, you can stack up to 62 of them to control up to 992 servos - all with the same 2 pins! Best of all, we even have a Python library you can use, so you'll be up and running instantly, to make your robotic creation com to life. The Adafruit PWM/Servo HAT is the perfect solution for any project that requires a lot of servos or PWM outputs! Each order comes with a Servo HAT, a 2-pin terminal block, four 3x4 headers and a 2x20 socket header. You'll need to do some light through-hole soldering to attach the headers onto the HAT circuit board, but its easy to do with basic soldering tools like a soldering iron and rosin core electronics solder. If you would like to stack multiple HATs onto one Pi, you can also pick up a 2x20 stacking header and a set of right-angle 3x4 headers that should be soldered on instead. Please note! This kit does not come with Raspberry Pi, servos, or required 5V power supply...
  • Raspberry Pi Camera Module V2-8 Megapixel,1080p
    Precio:  $4,809.00

    Raspberry Pi Camera Module V2-8 Megapixel,1080p

    -Titulo Original : Raspberry Pi Camera Module V2-8 Megapixel,1080p-Fabricante : RASPBERRY PI-Descripcion Original: Second Generation Raspberry Pi Camera Module with Fixed Focus Lens // Sony Exmor IMX219 Sensor Capable of 4K30, 1080P60, 720P180, 8MP Still // 3280 (H) x 2464 (V) Active Pixel Count // Maximum of 1080P30 and 8MP Stills in Raspberry Pi Board // 2A Power Supply Highly Recommended // Color: The Raspberry Pi Camera V2 features the same, tiny footprint (25mm x 23mm x 9mm) as the original Pi Camera module, but features an upgraded Sony IMX219 image sensor which has a native resolution of 8 megapixels. The fixed-focus lens can capture 3280 x 2464 pixel images and 1080p30, 720p60 and 640x480p90 video. The Raspberry Pi Camera V2 connects to the CSi connector of your Raspberry Pi via a 15cm long flexible ribbon cable. It is plug-and-play compatible latest version of the Raspbian operating system making it perfect for time-lapse photography, recording video, motion detection, and security applications...
  • Raspberry PI 3 Model B+ Plus
    Precio:  $8,589.00

    Raspberry PI 3 Model B+ Plus

    -Titulo Original : Raspberry PI 3 Model B+ Plus-Fabricante : Raspberr...
  • Adafruit Small-Size Perma-Proto Raspberry Pi Breadboard PCB.
    Precio:  $1,389.00

    Adafruit Small-Size Perma-Proto Raspberry Pi Breadboard PCB.

    -Titulo Original : Adafruit Small-Size Perma-Proto Raspberry Pi Breadboard PCB Kit [ADA1171]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1171 // Stock Type: Raspberry Pi >> Prototyping >> Model A+, B+, & Pi 2 // In Stock & Ready to Ship // We put a PermaProto quarter-sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It has the Cobbler baked right in. Simply solder the 2x13 pin header in and you get all the labeled breakouts with tons of prototyping space, power rails, mounting holes and that gorgeous silk. Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake off and no labeling. Then we thought about how people actually prototype - usually starting with a solderless breadboard and then transferring the parts to a more permanent PCB. That's when we realized what people would really like is a proto board that makes it easy! This proto-board is the PCB you always wish you had, but never realized it! We took the basic layout of a quarter-sized breadboard (the PCB has 17 rows) and turned that into a beautiful PCB. The top side has a white silkscreen, and the same markings you're familiar with, to make transferring components easy. The bottom has a 4-hole pad design that matches a classic breadboard, with 4 power bus lines on the sides, and no mask so you can easily cut traces when necessary. We used 1.2mm diameter drill holes so even parts with big leads will fit. All holes are thru-plated for strength - these wont peel off with rework. The finish is a gold plate - you won't get oxidation like with bare copper perf ! There are also tons of mounting holes so you can attach the PCB to your project box. Comes with one PCB and one box header, you'll need to do a little light soldering to attach the box header to the PCB but its fast and easy to do. To connect it to a Pi, you'll also need a 26-pin GPIO cable if you don't already have one. Adafruit Small-Size Perma-Proto Raspberry Pi Breadboard PCB Kit ( 15:15 ...
  • Adafruit DPI TFT Kippah for Raspberry Pi [ADA2454]
    Precio:  $3,119.00

    Adafruit DPI TFT Kippah for Raspberry Pi [ADA2454]

    -Titulo Original : Adafruit DPI TFT Kippah for Raspberry Pi [ADA2454]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2454 // Stock Type: Raspberry Pi >> Pi HATs & Plates >> Plates // In Stock & Ready to Ship // A TFT panel connected to a Raspberry Pi without the use of an HDMI decoder? What is this sorcery??? It's the DPI Kippah from Adafruit ! This HAT-like* board snaps onto a Raspberry Pi B+, A+, Pi 2, Pi 3 or Zero and with a little software configuration, allows you to have what  normally  would go out the HDMI port come up on a nice little flat screen. * Its not technically a HAT due to the lack of an on-board EEPROM, but its the same shape as a Pi HAT and its a covering of sorts, so we call it a kippah This is the Kippah with no touchscreen support . We have a version with touchscreen capabilities if that's your thing! Compared to our lovely HDMI backpacks, you don't have the extra cost or expense of an HDMI encoder/decoder. And you get a nice ultra-fast 18-bit color display with optional touch support. We tested it and it works great with our 5 and 7 displays at 800x480. This display is 'native' so it gets all the graphics accelleration capabilities, instant refresh, etc. you would get from an HDMI displayOK so, exciting right? But, what's the catch? The catch is  this add on board uses nearly every pin available on the Raspberry Pi and those pins are hardcoded, they cannot be moved or rearranged . The pins used are GPIO 2 through 21 inclusive. That means you don't get the UART RX/TX pins (no console cable) and you don't get the standard user I2C pins, the EEPROM I2C pins, or hardware SPI pins. You do get to use pins #22, #23, #24, #25, #26 and #27, and the USB ports are fine to use too. The other catch is that this display replaces the HDMI/NTSC output , so you can't have the DPI HAT and HDMI working at once, nor can you 'flip' between the two. Also, there's no PWM's available so you can't have precision backlight control unless you somehow rig up an external PWM generator with a 555 or something. Finally, we did test this setup with ...
Mostrar del 1 al 24 (de 41 productos)
Páginas de Resultados:  1  2  [Siguiente >>]