Arriba

Componentes Electrónicos > Circuito Integrado

Mostrar: 
Mostrar del 1 al 24 (de 174 productos)
Páginas de Resultados:  1  2  3  4  5 ...  [Siguiente >>] 
  • Adafruit 16 MHz Crystal + 20pF capacitors [ADA2215]
    Precio:  $1,029.00

    Adafruit 16 MHz Crystal + 20pF capacitors [ADA2215]

    -Titulo Original : Adafruit 16 MHz Crystal + 20pF capacitors [ADA2215]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2215 // Stock Type: Components & Parts >> Oscillators/Crystals // In Stock & Ready to Ship // Keep your microcontroller tickin' with a a fancy timing crystal. This 16.000 MHz model comes in a HC49/US 'short style' standard package and is breadboard friendly and easy to use with any microcontroller or device that requires an external crystal. We even include two 20pF capacitors!The crystal has 30PPM tolerance, 50PPM stability so it's good even for high precision needs (USB timing, long-term time-keeping, RF/PLL/VCO driving).To use, connect the two pins to XTAL-in and XTAL-out on your circuit (the package is symmetric so use whichever pin) and one capacitor each from a crystal pin to ground. Check your microcontroller datasheet in case you also need a 1 Megaohm resistor or any other components...
  • Adafruit 8-channel Bi-directional Logic Level Converter [ad
    Precio:  $2,659.00

    Adafruit 8-channel Bi-directional Logic Level Converter [ad

    -Titulo Original : Adafruit 8-Channel Bi-Directional Logic Level Converter [ADA395]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 395 // Stock Type: Breakout Boards >> Level Shifters & Expanders // In Stock & Ready to Ship // Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V. Although one can use resistors to make a divider, for high speed transfers, the resistors can add a lot of slew and cause havoc that is tough to debug. For that reason, we like using 4050/74LVX245 series and similar logic to perform proper level shifting. Only problem is that they are only good in one direction which can be a problem for some specialty bi-diectional interfaces and also makes wiring a little hairy. That's where this lovely chip, the TXB0108 bi-directional level converter comes in! This chip perform bidirectional level shifting from pretty much any voltage to any voltage and will auto-detect the direction . Only thing that doesn't work well with this chip is i2c (because it uses strong pullups which confuse auto-direction sensor). If you need to use pullups, you can but they should be at least 50K ohm - the ones internal to AVRs/Arduino are about 100K ohm so those are OK! Its a little more luxurious than a 74LVX245 but if you just don't want to worry about directional pins this is a life saver! Since this chip is a special bi-directional level shifter it does not have strong output pins that can drive LEDs or long cables, it's meant to sit on a breadboard between two logic chips! If you do not need instant bi-directional support, we suggest the 74LVX245 as below which has strong output drive. This breakout saves you from having to solder the very fine pitch packages that this chip comes with. We also add 0.1uF caps onto both sides and a 10K pull-up resistor on the output enable pin so you can use it right out of the box...
  • Adafruit Massive Arcade Button with LED - 100mm Red [ADA1185
    Precio:  $3,319.00

    Adafruit Massive Arcade Button with LED - 100mm Red [ADA1185

    -Titulo Original : Adafruit Massive Arcade Button with LED - 100mm Red [ADA1185]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1185 // Stock Type: Components & Parts >> Buttons // In Stock & Ready to Ship // OMG WATCH OUT! This 100mm diameter arcade button with a is so massive and inviting it may collapse upon itself and form a black hole from which not even light can escape! Until it does, however, it ready for all sorts of pressing and pushing. Science has shown no one can resist pressing its shiny surface and saying beep!. We've seen these on some games of skill in arcades, they're easy to mount on nearly any kind of enclosure. They're not waterproof or weatherproof, so best used indoors. This button has a domed red plastic cover with a black retaining ring around it. There's an optional LED included that will light up the button. The LED has a built in resistor so you can run it up to 12V but given the massive size and shallow depth of the button, it doesn't illuminate the entire button face evenly. The button activates a common arcade microswitch (included), the switch contacts are normally open. When the button is pressed, the contacts close. Massive Arcade Button with LED - 100mm Red ( 0:59 ...
  • Adafruit Touch Sensor Development Tools Resistive Touch Scre
    Precio:  $2,499.00

    Adafruit Touch Sensor Development Tools Resistive Touch Scre

    -Titulo Original : Touch Sensor Development Tools Resistive Touch Screen Controller (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1571 // Stock Type: Breakout Boards >> Touch // In Stock & Ready to Ship // Getting touchy performance with your screen's touch screen? Resistive touch screens are incredibly popular as overlays to TFT and LCD displays. Only problem is they require a bunch of analog pins and you have to keep polling them since the overlays themselves are basically just big potentiometers. If your microcontroller doesn't have analog inputs, or maybe you want just a way more elegant controller, the STMPE610 is a nice way to solve that problem. This breakout board features the STMPE610, which has both I2C and SPI interfaces available. There is also an interrupt pin that you can use to indicate when a touch has been detected to your microcontroller or microcomputer. We wrapped up the chip with a 3V voltage regulator and level shifting so it's safe to use with 3V or 5V logic. Its a nicely designed chip, and has very stable precise readings. We found its also a lot faster than trying to do all the readings on an Arduino. For the screens that have 1mm pitch FPC cables, you can plug the cable right into the connector. The majority of medium/large touchscreens have that kind of connector. If you have another kind of touch screen, the four X/Y contacts are available on 0.1 pitch breakouts so you can hand-solder or wire them. Getting started is super easy with our well-written STMPE610 Arduino library which supports I2C, hardware SPI, and software SPI . Plug any 1mm-pitch 4-wire resistive touchscreen to the on-board FPC connector. When you touch the screen, you'll get readings on the serial console. The wiring information is contained in the example sketch. Resistive Touch Screen Controller - STMPE610 ( 18:26 ...
  • Adafruit USB Microscope - 5MP interpolated 220x magnificatio
    Precio:  $13,139.00

    Adafruit USB Microscope - 5MP interpolated 220x magnificatio

    -Titulo Original : Adafruit USB Microscope - 5MP interpolated 220x magnification / 8 LEDs [ADA636]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 636 // Stock Type: Tools >> Test Equipment // In Stock & Ready to Ship // As electronics get smaller and smaller, you'll need a hand examining PCBs and this little USB microscope is the perfect tool. Its smaller and lighter than a large optical microscope but packs quite a bit of power in its little body. There's a 5.0 megapixel sensor inside and an optical magnifier that can adjust from 20x (for basic PCB inspection) to 220x (for detailed inspection). Eight white LEDs are angled right onto whatever you're examining so you get enough lighting to see, and are smoothly adjustable via a dial on the side. We've upgraded this microscope to 5.0 Megapixel (from 2.0M) and this one comes with two removable plastic caps to get close ups for a wider focusing range. If you plug this into any computer, it just shows up as a standard USB camera (we used this for our weekly Ask an Engineer show) and the Windows/Mac software lets you take snapshots using the button on the side of the microscope or direct from the software (so you don't move the camera). We tried a bunch of different USB microscopes and found this one to be the best combination of optical clarity, usability, and price. It's perfect for electronics hacking, rework, SMT (de)soldering, inspection, and soon you'll find yourself pulling it out to look and photograph all sort of cool small stuff around your lab and home. We took some snaps of this 'scope while looking at a tiny 0201-populated GPS board at 20x magnification and then at a raw die at 200x Package comes with a USB microscope with 4.5ft/140cm long cord and adjustable stand...
  • Adafruit WiFi / 802.11 Development Tools Feather M0 WiFi - A
    Precio:  $8,259.00

    Adafruit WiFi / 802.11 Development Tools Feather M0 WiFi - A

    -Titulo Original : WiFi / 802.11 Development Tools Adafruit Feather M0 WiFi - ATSAMD21 + ATWINC1500-Fabricante : ADAFRUIT-Descripcion Original: ATSAMD21G18 @ 48MHz with 3.3V logic/power // 256KB FLASH, 32KB SRAM, No EEPROM // 3.3V regulator (AP2112K-3.3) with 600mA peak current output, WiFi can draw 300mA peak during xmit // USB native support, comes with USB bootloader and serial port debugging // You also get tons of pins - 20 GPIO pins // Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather M0 WiFi w/ATWINC1500 - our take on an 'all-in-one' Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. Its an Adafruit Feather M0 with a WiFi module, ready to rock! We have other boards in the Feather family, check'em out here. Connect your Feather to the Internet with this fine new FCC-certified WiFi module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with built-in low-power management capabilites, Soft-AP, SSL TSL 1.2 support and rock solid performance. We were running our adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer but we had to go to work, so we unplugged it). This module is very fast & easy to use in comparison to other WiFi modules we've used in the past. This module works with 802.11b, g, or n networks & supports WEP, WPA and WPA2 encryption. You can connect to your own WiFi networks or create your own with Soft AP mode, where it becomes its own access point (we have an example of it creating a webserver that you can then control the Arduino's pins). You can clock it as fast as 12MHz for speedy, reliable packet streaming. And scanning/connecting to networks is very fast, just a second or two...
  • Adafruit Pro Trinket 5v 16mhz (1 Unidad)
    Precio:  $2,889.00

    Adafruit Pro Trinket 5v 16mhz (1 Unidad)

    -Titulo Original : Adafruit Pro Trinket 5V 16MHz (1 Piece)-Fabricante : Adafruit -Descripcion Original: Chip integrado ATmega328P en paquete QFN Velocidad de reloj de 16MHz, FLASH de 28K disponible El cargador de arranque USB con un buen indicador LED se parece a un USBtinyISP para que pueda programarlo con AVRdude y / o Arduino IDE (con algunas modificaciones simples de configuración). También tiene encabezados para un puerto FTDI para reprogramación Conector micro-USB para alimentación y / o carga USB, puede colocarlo en una caja o pegarlo con cinta adhesiva y usar cualquier cable USB para cuando desee reprogramar. Regulador de potencia incorporado de 5.0V con capacidad de salida de 150mA y caída ultra baja. Entrada de hasta 16 V, protección de polaridad inversa, protección térmica y de límite de corriente. Trinket tiene una hermana mayor en la ciudad: ¡Pro Trinket 5V! Pro Trinket combina todo lo que te gusta de Trinket con la familiaridad del chip Arduino de núcleo común, el ATmega328. Es como un Arduino Pro Mini con más pines y USB, tan delicioso. Trinket ya tiene un año, y aunque ha sido genial ver toneladas de pequeños proyectos, a veces solo necesitas más pines, más FLASH y más RAM. Es por eso que diseñamos Pro Trinket, con 18 GPIO, 2 entradas analógicas adicionales, 28K de flash y 2K de RAM. Al igual que el Trinket, tiene soporte de carga de arranque USB integrado: esta vez optamos por un conector MicroUSB. También agregamos el soporte Optiboot, para que pueda programar su Pro Trinket a través de USB o con un cable FTDI al igual que el Pro Mini y sus amigos. El Pro Trinket PCB mide solo 1.5 x 0.7 x 0.2 (sin encabezados) pero tiene casi la misma capacidad que un Arduino UNO. Por lo tanto, es excelente una vez que haya terminado un prototipo en un Arduino UNO oficial y quiera hacer el proyecto es más pequeño. El Pro Trinket 5V usa el chip Atmega328P, que es el mismo chip central en el Arduino UNO / Duemilanove / Mini / etc. a la misma velocidad y voltaje. Por lo tanto, le alegrará saber que no solo es Pro Trinket programable usando el IDE de Arduino como ya configuró, ¡pero el 99% de los proyectos de Arduino funcionarán de inmediato! Aquí hay algunas cosas que debe tener en cuenta al adaptar los bocetos de Arduino: los pines # 2 y # 7 no están disponibles (están exclusivamente para USB) El regulador de 5 V integrado puede proporcionar una salida de 150 mA, no una salida de 800 mA. No puede enchufar los protectores directamente en Pro Trinket. No hay un chip de serie a USB integrado. Esto es para mantener el Pro Trinket pequeño y económico, puede usar cualquier cable FTDI para conectar al puerto FTDI para una conexión en serie. nnection es solo para cargar código nuevo. El gestor de arranque en Pro Trinket usa 4KB de FLASH, por lo que el tamaño máximo de boceto es de 28,672 bytes. El gestor de arranque no afecta el uso de RAM...
  • Adafruit Power Relay FeatherWing [ADA3191]
    Precio:  $2,669.00

    Adafruit Power Relay FeatherWing [ADA3191]

    -Titulo Original : Adafruit Power Relay FeatherWing [ADA3191]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 3191 // Stock Type: Development Boards >> Feather >> Wings // In Stock & Ready to Ship // A Feather board without ambition is a Feather board without FeatherWings! This is the Power Relay FeatherWing . It gives you power to control, and control over power. Put simply, you can now turn on and off lamps, fans, solenoids, and other small appliances that run on up to 250VAC or DC power using any Feather board. Compared to our smaller Relay FeatherWings, this one can handle a beefy 1200 Watts! Works with all/any of our Feather boards, just wire up the relay control pin to whatever GPIO you like! Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Check out our range of Feather boards here. This Wing has a non-latching type relay. You can switch up to 10A of resistive-load current at 120VAC, 5A at 240VAC. With inductive loads, about half that. Check the datasheet for the relay for the exact switching capacity, as it depends on type of load and voltage type and magnitude. This relay is good for handling fairly large devices, computers, TVs, small appliances and more. Each FeatherWing comes with a fully assembled and tested PCB, header you can use to attach to your Feather. By soldering closed the jumper on the underside of the Wing you can select which pin you want to use for the relay control. Some light soldering is required. Please note: If using with high voltages (> 24V) use care and common sense! High voltages require experience, and are only for use by engineers who are comfortable with guidelines and know how to use them safely...
  • Adafruit Panel Mount 10K Potentiometer (Breadboard Friendly)
    Precio:  $1,269.00

    Adafruit Panel Mount 10K Potentiometer (Breadboard Friendly)

    -Titulo Original : Adafruit Panel Mount 10K Potentiometer (Breadboard Friendly) [ADA562]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 562 // Stock Type: Components & Parts >> Passives // In Stock & Ready to Ship // This potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 10K ohm potentiometer, with a grippy shaft. It's smooth and easy to turn, but not so loose that it will shift on its own. We like this one because the legs are 0.2 apart with pin-points, so you can plug it into a breadboard or perfboard. Once you're done prototyping, you can drill a hole into your project box and mount the potentiometer that way...
  • Adafruit (1095 Keyfob 4 Button RF Remote Control - 315MHz
    Precio:  $2,429.00

    Adafruit (1095 Keyfob 4 Button RF Remote Control - 315MHz

    -Titulo Original : Adafruit (1095 Keyfob 4 Button RF Remote Control - 315MHz-Fabricante : ADAFRUIT-Descripcion Original: Weight: 21.22g // Uses two CR2016 coin cells // A matching RF receiver is not included // This 4-button keyfob remote goes with our three basic 315MHz RF receiver modules. // This 4-button keyfob remote goes with our three basic 315MHz RF receiver modules. It will work with all of them, sending out one of four commands that match up with the four outputs. Its small and light weight and will work up to 25 feet away depending on line-of-sight and obstructions. Since this is just a transmitter, if you have multiple receivers, it will turn all of them on and off at the same time (there is no sub-addressing) A matching RF receiver is not included, you'll need to purchase one in addition...
  • Adafruit IR Break Beam Sensor - 5mm LEDs [ADA2168]
    Precio:  $2,079.00

    Adafruit IR Break Beam Sensor - 5mm LEDs [ADA2168]

    -Titulo Original : Adafruit IR Break Beam Sensor - 5mm LEDs [ADA2168]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2168 // Stock Type: Sensors >> Motion // In Stock & Ready to Ship // Infrared (IR) break-beam sensors are a simple way to detect motion. They work by having an emitter side that sends out a beam of human-invisible IR light, then a receiver across the way which is sensitive to that same light. When something passes between the two, and its not transparent to IR, then the 'beam is broken' and the receiver will let you know.Compared to PIR sensors, breakbeams are faster and allow better control of where you want to detect the motion. Compared to Sonar modules, they're less expensive. However, you do need both emitter and receiver on opposite sides of the area you want to monitor.This is the 5mm IR  version.   It works up to 50cm / 20. You can power it from 3.3V or 5V, but 5V will get you better range and is what we suggest. The receiver is open collector transistor output which means that you do need a pull up resistor if you want to read a digital signal off the signal wire. Most microcontrollers have the ability to turn on a built in pull up resistor. If you do not, connect a 10K resistor between the white wire of the receiver and the red wire. If you want to control a relay or LED or whatever, it can sink up to 100mA to ground Check out our IR breakbeam tutorial for how to get started quickly We also carry a 3mm version that works for slightly shorter distances...
  • Adafruit FeatherWing OLED - 128x32 OLED Add-on for All Feath
    Precio:  $4,399.00

    Adafruit FeatherWing OLED - 128x32 OLED Add-on for All Feath

    -Titulo Original : Adafruit FeatherWing OLED - 128x32 OLED Add-on for All Feather Boards [ADA2900]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2900 // Stock Type: Development Boards >> Feather >> Wings // In Stock & Ready to Ship // A Feather board without ambition is a Feather board without FeatherWings! This is the FeatherWing OLED : it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight!These displays are small, only about 1 diagonal, but very readable due to the high contrast of an OLED display. This screen is made of 128x32 individual white OLED pixels and because the display makes its own light, no backlight is required. This reduces the power required to run the OLED and is why the display has such high contrast; we really like this miniature display for its crispness! We also toss on a reset button and three mini tactile buttons called A B and C so you can add a mini user interface to your feather.Tested working with  all Feather boards. The OLED uses only the two I2C pins on the Feather, and you can pretty much stack it with any other FeatherWing, even ones that use I2C since that is a shared bus. To use, Check out our tutorial ! It has schematics, datasheets, files, and code examples. Check out our range of Feather boards here...
  • Adafruit Green 7-segment clock display - 0.56 digit height [
    Precio:  $1,389.00

    Adafruit Green 7-segment clock display - 0.56 digit height [

    -Titulo Original : Adafruit Green 7-segment clock display - 0.56 digit height [ADA813]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 813 // Stock Type: LEDs >> Segmented // In Stock & Ready to Ship // Design a clock, timer or counter into your next project using our pretty 4-digit seven-segment display. These bright crisp displays are good for adding numeric output. Besides the four 7-segments, there are decimal points on each digit and an extra wire for colon-dots in the center (good for time-based projects). These are ultra bright 125mcd! You can drive these with less current to get the same brightness to save power, or crank them up to 20mA and have them really bright. These displays are multiplexed, common-cathode. What that means it that you can use a 74HC595 or just 8 microcontroller pins if you can spare them to control the 8 anodes (7-seg + decimal) at about ~15mA each, and then connect NPN transistors or a TPIC6B595 to the cathodes to sink the 8*20mA = ~120mA maximum per digit. These come in a bright green color, we also have many other sizes and colors...
  • Adafruit Vibrating Mini Motor Disc [ADA1201]
    Precio:  $1,119.00

    Adafruit Vibrating Mini Motor Disc [ADA1201]

    -Titulo Original : Adafruit Vibrating Mini Motor Disc [ADA1201]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1201 // Stock Type: Robotics & CNC >> Robotics // In Stock & Ready to Ship // *BZZZZZZZZZZ* Feel that? That's your little buzzing motor, and for any haptic feedback project you'll want to pick up a few of them. These vibe motors are tiny discs, completely sealed up so they're easy to use and embed. Two wires are used to control/power the vibe. Simply provide power from a battery or microcontroller pin (red is positive, blue is negative) and it will buzz away. Works from 2V up to 5V, higher voltages result in more current draw but also a stronger vibration. If you want to reduce the current draw/strength (for example, to control it directly from an Arduino pin) try putting a resistor (100 to 1000 ohms) in series. For full power control, a small PN2222 transistor can control a motor easily, some experimentation may be required! Vibrating Mini Motor Disc ( 6:47 ...
  • Adafruit Electroluminescent (EL) Panel - 10cm x 10cm Blue [A
    Precio:  $3,659.00

    Adafruit Electroluminescent (EL) Panel - 10cm x 10cm Blue [A

    -Titulo Original : Adafruit Electroluminescent (EL) Panel - 10cm x 10cm Blue [ADA624]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 624 // Stock Type: EL Wire/Tape/Panel >> EL Panels // In Stock & Ready to Ship // EL panel is the big sister to EL wire - it has the same glow effect but with a flat shape instead of a round shape. This is a big sheet of flexible plastic coated with EL material so its like one big glowing square. It emits an even glow over the entire shape. The glowing part of the panel is 10 cm x 10 cm (approx: 4 x 4). There's a plastic coating is about 10.4cm x 10.4cm. Its covered in what seems to be PVC, the tape is thus weather-proof - but note that the connectors are NOT waterproof, just a bit of heatshrink. This isn't something we would suggest leaving outdoors for extended periods. You can attach it by sewing through the clear plastic edging, or gluing the back to a flat surface. It is flexible but will crease and damage if folded. You can cut the panel up as long as the shape you cut out is continuous and has the JST cable attached. This panel is a blue color when lit and appears blue when off. Because EL tape has more surface area than wire, it requires a more powerful inverter. We suggest you use our 4xAAA inverter which is strong enough to power a single panel at once - plug it in and turn it on! For more permanent installations, the 12V EL inverter can also power a single panel and run off 8xAA batteries or a wall adapter....
  • Adafruit Fingerprint Sensor 751 - Scanner De Huella Digital
    Precio:  $10,149.00

    Adafruit Fingerprint Sensor 751 - Scanner De Huella Digital

    -Titulo Original : Adafruit Fingerprint sensor-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 751 // Stock Type: Sensors >> Biometric // In Stock & Ready to Ship // Secure your project with biometrics - this all-in-one optical fingerprint sensor will make adding fingerprint detection and verification super simple. These modules are typically used in safes - there's a high powered DSP chip that does the image rendering, calculation, feature-finding and searching. Connect to any microcontroller or system with TTL serial, and send packets of data to take photos, detect prints, hash and search. You can also enroll new fingers directly - up to 162 finger prints can be stored in the onboard FLASH memory. There's a red LED in the lens that lights up during a photo so you know its working. We like this particular sensor because not only is it easy to use, it also comes with fairly straight-forward Windows software that makes testing the module simple - you can even enroll using the software and see an image of the fingerprint on your computer screen. But, of course, we wouldn't leave you a datasheet and a good luck! - we wrote a full Arduino library so that you can get running in under 10 minutes. The library can enroll and search so its perfect for any project . We've also written a detailed tutorial on wiring and use . This is by far the best fingerprint sensor you can get...
  • Adafruit USB Extension Cable - 3 meters / 10 ft long [ADA993
    Precio:  $1,649.00

    Adafruit USB Extension Cable - 3 meters / 10 ft long [ADA993

    -Titulo Original : Adafruit USB Extension Cable - 3 meters / 10 ft long [ADA993]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 993 // Stock Type: Cables >> USB Cables // In Stock & Ready to Ship // This handy USB extension cable will make it easy for you to extend your USB cable when it won't reach. The connectors are gold plated for years of reliability. We use these handy cables all over our factory and homes. Cable is standard Adafruit black. Cable length: 10 feet (3 meters...
  • Adafruit Mini Metal Speaker w/ Wires - 8 ohm 0.5W [ADA1890]
    Precio:  $1,339.00

    Adafruit Mini Metal Speaker w/ Wires - 8 ohm 0.5W [ADA1890]

    -Titulo Original : Adafruit Mini Metal Speaker w/ Wires - 8 ohm 0.5W [ADA1890]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1890 // Stock Type: Components & Parts >> Speakers // In Stock & Ready to Ship // Listen up! This tiny 1 diameter speaker cone is the perfect addition to any small audio project where you need an 8 Ω impedance and will be using 0.5W or less of power. We particularly like this cone as it's very simple and its metal body is extremely lightweight. It's very similar to the speaker in the Drawdio kit. Works great with our Wave shield or class D amplifier board . Just be careful not to overdrive it if you're using the class D amp breakouts as it can put 1.7W into the speaker, blowing it out! Start with lower volume and increase carefully...
  • Adafruit SI1145 Digital UV Index/IR / Visible Light Sensor [
    Precio:  $2,569.00

    Adafruit SI1145 Digital UV Index/IR / Visible Light Sensor [

    -Titulo Original : Adafruit SI1145 Digital UV Index/IR / Visible Light Sensor [ADA1777]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1777 // Stock Type: Sensors >> Light/Color/Photo // In Stock & Ready to Ship // Remember when you were a kid and there was a birthday party at the pool and your parents totally embarrassed you by slathering you all over with sunscreen and you were all MOM I HAVE ENOUGH SUNSCREEN and she wouldn't listen? Well, if you had this UV Index sensor connected up to an Arduino you could have said According to this calibrated SI1145 sensor from SiLabs, the UV index right now is 4.5 which means I do not need more sunscreen and she would have been so impressed with your project that you could have spent more time splashing around. The SI1145 is a new sensor from SiLabs with a calibrated light sensing algorithm that can calculate UV Index. It doesn't contain an actual UV sensing element, instead it approximates it based on visible & IR light from the sun. We took this outside a couple days and compared the calculated UV index with the news-reported index and found it was very accurate! It's a digital sensor that works over I2C so just about any microcontroller can use it. The sensor also has individual visible and IR sensing elements so you can measure just about any kind of light - we only wrote our library to printout the 'counts' rather than the calculate the exact values of IR and Visible light so if you need precision Lux measurement check out the TSL2561. If you're feeling really advanced, you can connect up an IR LED to the LED pin and use the basic proximity sensor capability that is in the SI1145 as well. We wrapped this nice little sensor up on a PCB with level shifting and regulation circuitry so you can safely use it with 3 or 5V microcontrollers. If you are using an Arduino, we've got a lovely tutorial and library already written up with example code so you can quickly read sensor readings and the UV index in under 10 minutes. Each order comes with one fully assembled and tested PCB breakout and a small piece of header. You'll need to so...
  • Adafruit TCA9548A I2C Multiplexer [ADA2717]
    Precio:  $2,229.00

    Adafruit TCA9548A I2C Multiplexer [ADA2717]

    -Titulo Original : Adafruit TCA9548A I2C Multiplexer [ADA2717]-Fabricante : ADAFRUIT-Descripcion Original: Finally, a way to get up to 8 same-address I2C devices hooked up to one microcontroller - this multiplexer acts as a gatekeeper, shuttling the commands to the selected set of I2C pins with your command. // Using it is fairly straight-forward: the multiplexer itself is on I2C address 0x70 (but can be adjusted from 0x70 to 0x77) and you simply write a single byte with the desired multiplexed output number to that port, and bam - any future I2C packets will get sent to that port. In theory, you could have 8 of these multiplexers on each of 0x70-0x77 addresses in order to control 64 of the same-I2C-addressed-part. // Like all Adafruit breakouts, we put this nice chip on a breakout for you so you can use it on a breadboard with capacitors, and pullups and pulldowns to make usage a snap. Some header is required and once soldered in you can plug it into a solderless-breadboard. The chip itself is 3V and 5V compliant so you can use it with any logic level. // You just found the perfect I2C sensor, and you want to wire up two or three or more of them to your Arduino when you realize Uh oh, this chip has a fixed I2C address, and from what I know about I2C, you cannot have two devices with the same address on the same SDA/SCL pins! Are you out of luck? You would be, if you didn't have this ultra-cool TCA9548A 1-to-8 I2C multiplexer! Finally, a way to get up to 8 same-address I2C devices hooked up to one microcontroller - this multiplexer acts as a gatekeeper, shuttling the commands to the selected set of I2C pins with your command. Using it is fairly straight-forward: the multiplexer itself is on I2C address 0x70 (but can be adjusted from 0x70 to 0x77) and you simply write a single byte with the desired multiplexed output number to that port, and bam - any future I2C packets will get sent to that port. In theory, you could have 8 of these multiplexers on each of 0x70-0x77 addresses in order to control 64 of the same-I2C-addressed-part. Like all Adafruit breakouts, we put this nice chip on a breakout for you so you can use it on a breadboard with capacitors, and pullups and pulldowns to make usage a snap. Some header is required and once soldered in you can plug it into a solderless-breadboard. The chip itself is 3V and 5V compliant so you can use it with any logic level...
  • Adafruit Diffused Blue 3mm LED - 25 pack (1 piece)
    Precio:  $2,329.00

    Adafruit Diffused Blue 3mm LED - 25 pack (1 piece)

    -Titulo Original : Adafruit Accessories Diffused Blue 3mm LED - 25 pack (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 780 // Stock Type: LEDs >> Bare LEDs // In Stock & Ready to Ship // Need some indicators? We are big fans of these diffused blue LEDs, as featured in the LoL shield. They are really bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project.Pack of 25 diffused blue LEDs3mm diameter465-470nm wavelength3.0-3.4V Forward Voltage, at 20mA current500+ mcd typical brightness If you need some help using LEDs, please read our Introduction to using LEDs tutorial for any electronics project...
  • Adafruit 16mm Illuminated Pushbutton - Green Latching On/Off
    Precio:  $1,309.00

    Adafruit 16mm Illuminated Pushbutton - Green Latching On/Off

    -Titulo Original : Adafruit 16mm Illuminated Pushbutton - Green Latching On/Off Switch [ADA1443]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1443 // Stock Type: Components & Parts >> Buttons // In Stock & Ready to Ship // A switch is a switch, and an LED is an LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that can be controlled separately from the switch action - either to indicate or just to look good. The body is a black plastic with the LED built inside. There are two contacts for the button and two contacts for the LED, one marked + and one -. The forward voltage of the LED is about 2.2V so connect a 220 to 1000 ohm resistor in series just as you would with any other LED to your 3V or higher power supply. This particular button has a green body and LED and is latching on/off. The two switch contacts are either connected or disconnected. When you push the button they will switch from one to the other, like an on-off switch. The LED is separated from the button, so you can make it light up when on, light up when off, always lit, etc. 16mm Illuminated Pushbuttons ( 7:54 ...
  • Adafruit NeoPixel NeoMatrix 8x8-64 RGB LED Pixel Matrix [ADA
    Precio:  $6,989.00

    Adafruit NeoPixel NeoMatrix 8x8-64 RGB LED Pixel Matrix [ADA

    -Titulo Original : Adafruit NeoPixel NeoMatrix 8x8-64 RGB LED Pixel Matrix [ADA1487]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1487 // Stock Type: NeoPixels >> Boards // In Stock & Ready to Ship // Put on your sunglasses before wiring up this LED matrix - 64 eye-blistering RGB LEDs adorn the NeoMatrix for a blast of configurable color. Arranged in an 8x8 matrix, each pixel is individually addressable. Only one microcontroller pin is required to control all the LEDs, and you get 24 bit color for each LED. Wiring it up is easy: there are two 3-pin connection ports. Solder wires to the input port and provide 5VDC to the +5V and ground pins, then connect the DIN pin to your microcontroller. If you're using our NeoPixel Arduino library, use digital #6. You'll also need to make a common ground from the 5V power supply to the microcontroller/Arduino. Since each LED can draw as much as 60mA (thats up to 3.5 Amps per panel if all LEDs are on bright white!) we suggest our 5V 2A power supply. For most uses, you'll see about 1-2A of current per panel. If, say, you need MORE blinky, you can chain these together. For the second shield, connect the DIN connection to the first panel's DOUT. Also connect a ground pin together and power with 5V. There you go! You can chain as many as you'd like although after 4 or more panels you may run low on RAM if you're using an UNO. Watch your power usage too, you may need a 5V 10A power supply for so many of these! There is a single data line with a very timing-specific protocol. Since the protocol is very sensitive to timing, it requires a real-time microconroller such as an AVR, Arduino, PIC, mbed, etc. It cannot be used with a Linux-based microcomputer or interpreted microcontroller such as the netduino or Basic Stamp. Our wonderfully-written Neopixel library for Arduino supports these pixels! As it requires hand-tuned assembly it is only for AVR cores but others may have ported this chip driver code so please google around. An 8MHz or faster processor is required. Our detailed NeoPixel Uberguide has everything you need to use NeoPixels in any shape an...
  • Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]
    Precio:  $5,329.00

    Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]

    -Titulo Original : Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 390 // Stock Type: Power >> Solar >> Chargers // In Stock & Ready to Ship // NOTE: This product is only designed for use with solar panels sold at the Adafruit store. We cannot guarantee this will work with solar panels purchased elsewhere. Please purchase this kit and panels from Adafruit to ensure optimized functionality! A 2.1mm adapter cable is also required to adapt a solar panel to the DC power jack. Make your projects to go green this summer with our specialized USB/Solar Lithium Ion Polymer Battery charger! This charger is a very unique design, perfect for outdoor projects, or DIY iPod chargers. We've spent over a year testing and tinkering with this charger to come up with a plug and play solution to charging batteries with the sun and we're really pleased with what we ended up with. Easy to use! Pick up any of our many 3.7V/4.2V LiIon batteries , and a 6V solar panel . Plug the battery into the BATT port using a 2-pin JST cable and the solar panel into the DC jack using a 2.1mm adapter cable Put the solar panel outside (and keep the battery out of the sun, it needs to be kept cool!) to start charging. You can power another project like a Mintyboost at the same time by connecting to the LOAD output port Our carefully designed charger is designed specifically for solar charging, and will automatically draw the most current possible from the panel in any light condition! Even thought it isn't a 'true' MPPT (max power point tracker), it has near-identical performance without the additional cost of a buck-converter. Our detailed tutorial on how to use this charger includes a design document explaining how it all works. For use with Adafruit Lipoly/LiIon batteries only! Other batteries may have different voltage, chemistry, polarity or pinout. Comes with an assembled charger board, a 2-pin JST cable that will fit into either the BATT or LOAD ports, and a large stabilization capacitor that must be installed in your finished project. Doe...
Mostrar del 1 al 24 (de 174 productos)
Páginas de Resultados:  1  2  3  4  5 ...  [Siguiente >>]