Arriba

Componentes Electrónicos > Circuito Integrado

Mostrar: 
Mostrar del 1 al 24 (de 169 productos)
Páginas de Resultados:  1  2  3  4  5 ...  [Siguiente >>] 
  • Adafruit Dual H-Bridge Motor Driver for DC or Steppers - 600
    Precio:  $1,919.00

    Adafruit Dual H-Bridge Motor Driver for DC or Steppers - 600

    -Titulo Original : Adafruit Dual H-Bridge Motor Driver for DC or Steppers - 600mA - L293D [ADA807]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 807 // Stock Type: Components & Parts >> IC & Transistors // In Stock & Ready to Ship // Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as the drivers in our Adafruit Motorshield. If you accidentally damaged the drivers in a shield, you can use one of these puppies to replace it. Or you can breadboard something on your own! Each chip contains two full H-bridges (four half H-bridges). That means you can drive four solenoids, two DC motors bi-directionally, or one stepper motor. Just make sure they're good for under 600 mA since that's the limit of this chip. They do handle a peak of 1.2A but that's just for a short amount of time. What we like most about this particular driver is that it There's a PWM input per driver so you can control motor speed. Runs at 5V logic. Good for motor voltages from 4.5V up to 36V! This wont work well for 3V motors. The motor voltage is separate from the logic voltage...
  • Adafruit Rotary Encoder (1 piece)
    Precio:  $2,059.00
    Expira: 28/12/2020

    Adafruit Rotary Encoder (1 piece)

    -Titulo Original : Adafruit Accessories Rotary Encoder (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 377 // Stock Type: Sensors >> Touch // In Stock & Ready to Ship // This rotary encoder is the best of the best, its a high quality 24-pulse encoder, with detents and a nice feel. It is panel mountable for placement in a box, or you can plug it into a breadboard (just cut/bend the two mechanical side tabs.) We also include a nice soft-touch knob with an arrow in it, fits perfectly and looks great. This encoder also has a push-button built into it so you can press onto the knob to close a separate switch. One side has a 3 pin connector (ground and two coding pins) and the other side has two pins for a normally-open switch.Rotary encoders are useful as rotation sensors or selectors and look similar to potentiometers. However they are not like potentiometers at all, so it's important to realize the difference! These rotary encoders rotate all the way around continuously, and are divided up into 24 'segments'. Each segment has a click-y feeling to it, and each movement clockwise or counter-clockwise causes the two switches to open and close. There is no way to know what the current 'position' is - instead you would use a microcontroller to count how many 'clicks' left or right it has been turned. If you need to detect rotational 'position' a potentiometer would be a better choice...
  • Adafruit Mini Pan-Tilt Kit - Assembled with Micro Servos
    Precio:  $5,859.00

    Adafruit Mini Pan-Tilt Kit - Assembled with Micro Servos

    -Titulo Original : Adafruit Mini Pan-Tilt Kit - Assembled with Micro Servos-Fabricante : ADAFRUIT-Descripcion Original: Service will take place at the customer's location // Removal of existing CPU from desktop // Installation of one customer-supplied CPU // Installing new drivers // Component test and cleanup // This fully-assembled pan-tilt kit is the perfect way to give your project full range motion with two micro servos. The pan-tilt can rotate roughly 180° from side-to-side and can tilt up&downwards around 150°. It also comes fully assembled with two Micro Servos (SG-90 or SG-92 type) included and a 38mm x 36mm space to mount a camera or sensor or whatever you like. Since the motors are plain, every-day analog servos, you can use any microcontroller or driver. They're good for beginners who want to make stuff move and the pan-tilt is an easy way to give whatever you're making both left-right and up-down motion. In our demo, we hooked this up with a Trinket Pro and made it do a little dance with the Arduino Servo library...
  • Adafruit Audio IC Development Tools Stereo 2.8W Class D Audi
    Precio:  $4,039.00

    Adafruit Audio IC Development Tools Stereo 2.8W Class D Audi

    -Titulo Original : Audio IC Development Tools Stereo 2.8W Class D Audio Amplifier - I2C Control AGC - TPA2016 (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1712 // Stock Type: Breakout Boards >> Amplifiers/Sound // In Stock & Ready to Ship // A mini class D with AGC and I2C control? Yes please! This incredibly small stereo amplifier is surprisingly powerful. It is able to deliver 2 x 2.8W channels into 4 ohm impedance speakers (@ 10% THD) and it has a i2c control interface as well as an AGC (automatic gain control) system to keep your audio from clipping or distorting. If you don't want to use I2C to control it, it does start up on with 6dB gain by default and the AGC set up for most music playing. We do suggest using it with a microcontroller to configure it, however, since its quite powerful. Settings are not stored in the chip, so you'll need to adjust any gain & AGC amplification settings every time the amp is powered up. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, it's incredibly efficient (89% efficient when driving an 8Ω speaker at 1.5 Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell if it got hot. This board is a welcome upgrade to basic LM386 amps! The inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the R- and L- to ground. The outputs are Bridge Tied - that means they connect directly to the outputs, no connection to ground. The output is a ~300KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. Comes with a fully assembled and tested breakout board with 1.0uF input capacitors. We also include 3.5mm screw-terminal blocks so you can easily attach/detach your speakers, and some header in case you want to plug it into a breadboard. Speakers are not includ...
  • Adafruit (1095 Keyfob 4 Button RF Remote Control - 315MHz
    Precio:  $3,169.00

    Adafruit (1095 Keyfob 4 Button RF Remote Control - 315MHz

    -Titulo Original : Adafruit (1095 Keyfob 4 Button RF Remote Control - 315MHz-Fabricante : ADAFRUIT-Descripcion Original: Weight: 21.22g // Uses two CR2016 coin cells // A matching RF receiver is not included // This 4-button keyfob remote goes with our three basic 315MHz RF receiver modules. // This 4-button keyfob remote goes with our three basic 315MHz RF receiver modules. It will work with all of them, sending out one of four commands that match up with the four outputs. Its small and light weight and will work up to 25 feet away depending on line-of-sight and obstructions. Since this is just a transmitter, if you have multiple receivers, it will turn all of them on and off at the same time (there is no sub-addressing) A matching RF receiver is not included, you'll need to purchase one in addition...
  • Adafruit FT232H Breakout - General Purpose USB to GPIO+SPI+I
    Precio:  $5,079.00

    Adafruit FT232H Breakout - General Purpose USB to GPIO+SPI+I

    -Titulo Original : Adafruit FT232H Breakout - General Purpose USB to GPIO+SPI+I2C-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2264 // Stock Type: Breakout Boards >> Other // In Stock & Ready to Ship // Wouldn't it be cool to drive a tiny OLED display , read a color sensor , or even just flash some LEDs directly from your computer?  Sure you can program an Arduino  or Trinket  to talk to these devices and your computer, but why can't your computer just talk to those devices and sensors itself?  Well, now your computer can talk to devices using the Adafruit FT232H breakout board!What can the FT232H chip do?  This chip from FTDI  is similar to their USB to serial converter chips but adds a 'multi-protocol synchronous serial engine' which allows it to speak many common protocols like SPI, I2C, serial UART, JTAG, and more!  There's even a handful of digital GPIO pins that you can read and write to do things like flash LEDs, read switches or buttons, and more.  The FT232H breakout is like adding a little swiss army knife for serial protocols to your computer!This chip is powerful and useful to have when you want to use Python (for example) to quickly iterate and test a device that uses I2C, SPI or plain general purpose I/O. There's no firmware to deal with, so you don't have to deal with how to send data to and from an Arduino which is then sent to and from an electronic sensor or display or part.This breakout has an FT232H chip and an EEPROM for onboard configuration. You can read tons more about this chip from FTDI's page and check out our tutorial on how to get started and use our Python code to control the FT232H with Mac/Win/Linux...
  • Adafruit Stereo Fm Transmitter With Rds/rbds Breakout - Si4
    Precio:  $6,009.00

    Adafruit Stereo Fm Transmitter With Rds/rbds Breakout - Si4

    -Titulo Original : Adafruit Stereo FM Transmitter with RDS/RBDS Breakout - Si4713-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1958 // Stock Type: Breakout Boards >> Radio // In Stock & Ready to Ship // Description yaaar!e your very own pirate radio station with this fm radio transmitter. This breakout board, based on the best-of-class si4713, is an all-in-one stereo audio fm transmitter that can also transmit rds/rbds data!wire up to your favorite microcontroller (we suggest an arduino) to the i2c data lines to set the transmit frequency and play line-level audio into the stereo headphone jack. Boom! now you are the media. . Listen using any fm receiver such as your car or pocket radio receiver - this is an easy way to transmit audio up to about 10 meters / 30 feet away. This transmitter even has rds/rbds support - that's text/data transmissions that many modern fm receivers support. (it's how some car radios can display the fm station and current song playing). You can transmit just about any text you want, set the station identifier as well as the 'freeform' buffer. Best of all, you'll be up and running in minutes with our awesome arduino library, example code and tutorial...
  • Adafruit 74LVC245 - Breadboard Friendly 8-bit Logic Level Sh
    Precio:  $1,819.00

    Adafruit 74LVC245 - Breadboard Friendly 8-bit Logic Level Sh

    -Titulo Original : Adafruit 74LVC245 - Breadboard Friendly 8-bit Logic Level Shifter [ADA735]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 735 // Stock Type: Components & Parts >> IC & Transistors // In Stock & Ready to Ship // Most of our customers love using the Arduino for prototyping, design and invention but find themselves stuck when trying to connect the Arduino to the latest sensors, displays, controllers, interfaces, etc. as they are almost all 3.3V logic these days. We try to solve this problem by having all our breakout boards be 5V compatible or when that's not possible, including a level shifter chip but there are still thousands of tempting devices out there. This chip solves the problem of how to interface 3.3V logic devices to a 5.0V logic chip such as the Arduino. Most 3.3V devices do not like being run with 5V signals and can be damaged or flaky. The 74LVC245 is designed so that even when it runs at 1.8V, it still happily accepts 5V signals in one pin and converts it to a lower logic level on the opposite pin. This chip is only for digital signals, it doesn't convert analog signals (you need an op amp for that). It has 8 pipes it can convert but it won't work with bi-directional/pull-up based devices such as I2C or 1-Wire. It does work great for SPI, Serial, Parallel bus, and other logic interfaces. Using it is simple. We suggest checking out the 74LVC245 datasheet for details but essentially: connect VCC to your logic level you want to convert to (say 3.3V), Ground connects to Ground. Wire OE (output enable) to ground to enable the device and DIR (direction) to VCC. Then digital logic on the A pins up to 5V will appear on the B pins shifted down to the VCC logic...
  • Adafruit LED Lighting Development Tools 8-Channel PWM or Ser
    Precio:  $3,749.00

    Adafruit LED Lighting Development Tools 8-Channel PWM or Ser

    -Titulo Original : LED Lighting Development Tools 8-Channel PWM or Servo FeatherWing Add-on For All Feather Boards (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: There's an I2C-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! // It is 5V compliant, which means you can control it from a 3.3V Feather and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) // 6 address select pins so you can stack up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs // Adjustable frequency PWM up to about 1.6 KHz // 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate // A Feather board without ambition is a Feather board without FeatherWings! This is the 8-Channel PWM or Servo​ FeatherWing, you can add 8 x 12-bit PWM outputs to your FeatherWing. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top or bottom of your Feather board and let the board take flight! You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. What now? You could give up OR you could just get our handy PWM and Servo FeatherWing. It's a lot like our popular PWM/Servo Shield but with half the channels & squished into a nice small portable size and works with any of our Feather boards. Since the FeatherWing only uses the I2C (SDA & SCL pins), it works with any and all Feathers- ATmega32u4, ATSAM M0 or ESP8266-based. You can stack it with any other FeatherWing or with itself (just make sure you have each wing with a unique I2C address). This product comes with a fully tested and assembled wing as well as 2 pieces of 3x4 male straight header (for servo/LED plugs), a 2-pin terminal block (for power) and a stick of 0.1 header so you can plug into a Feather. A little light soldering will be required to assemble and customize the board by attaching the desired headers but it is a 15 minute task that even a beginner can do. Technical Details Dimensions: 50.8mm x 22.9mm x 1.6mm / 2 x 0.9 x 0.06 Weight: 3.9...
  • Adafruit Adxl326 - 5v Ready Triple-axis Accelerometer (+-16
    Precio:  $5,459.00

    Adafruit Adxl326 - 5v Ready Triple-axis Accelerometer (+-16

    -Titulo Original : Adafruit ADXL326 - 5V ready triple-axis accelerometer (+-16g analog out) [ADA1018]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1018 // Stock Type: Sensors >> Motion // In Stock & Ready to Ship // We've now got a wider range version of favorite triple-axis accelerometer - it even has an on-board 3.3V regulator - making it a perfect choice for interfacing with a 5V microcontroller such as the Arduino. This breakout comes with 3 analog outputs for X, Y and Z axis measurements on a 0.75x0.75 breakout board. The ADXL326 is the latest and greatest from Analog Devices, known for their exceptional quality MEMS devices. The VCC takes up to 5V in and regulates it to 3.3V with an output pin. The analog outputs are ratiometric: that means that 0g measurement output is always at half of the 3.3V output (1.65V), -16g is at 0v and 16g is at 3.3V with full scaling in between. Fully assembled and tested. Comes with 8 pin 0.1 standard header in case you want to use it with a breadboard or perfboard. Two 2mm (0.08) mounting holes for easy attachment. The XYZ filter capacitors are 0.1uF for a 50 Hz bandwidth See the ADXL326 webpage for datasheets and mor...
  • Adafruit Industries 1578 Lithium Ion Polymer Battery - 3.7v
    Precio:  $2,699.00

    Adafruit Industries 1578 Lithium Ion Polymer Battery - 3.7v

    -Titulo Original : ADAFRUIT INDUSTRIES 1578 Lithium Ion Polymer Battery - 3.7v 500mAh-Fabricante : ADAFRUIT-Descripcion Original: Kit includes: Circuit Playground Express - Developer Edition USB cable - A/MicroB - 3ft 3 x Alkaline AAA batteries 3 x AAA Battery Holder with On/Off Switch, JST, and Belt Clip Mini Storage Box Here's some of the great goodies baked in to each Circuit Playground: 10 x mini NeoPixels, each one can display any color 1 x Motion sensor (LIS3DH triple-axis accelerometer with tap detection, free-fall detection) 1 x Temperature sensor (thermistor) 1 x Light sensor (phototransistor). Can also act as a color sensor and pulse sensor. 1 x Sound sensor (MEMS microphone) 1 x Mini speaker with class D amplifier (7.5mm magnetic speaker/buzzer) 2 x Push buttons, labeled A and B 1 x Slide switch Infrared receiver and transmitter - can receive and transmit any remote control codes, as well as send messages between Circuit Playground Expresses. Can also act as a proximity sensor. 8 x alligator-clip friendly input/output pins Includes I2C, UART, 8 pins that can do analog inputs, multiple PWM output 7 pads can act as capacitive touch inputs and the 1 remaining is a true analog output Green ON LED so you know its powered Red #13 LED for basic blinking Reset button ATSAMD21 ARM Cortex M0 Processor, running at 3.3V and 48MHz 2 MB of SPI Flash storage, used primarily with CircuitPython to store code and libraries. MicroUSB port for programming and debugging USB port can act like serial port, keyboard, mouse, joystick or MIDI...
  • Adafruit OctoWS2811 Adapter for Teensy 3.1
    Precio:  $5,579.00

    Adafruit OctoWS2811 Adapter for Teensy 3.1

    -Titulo Original : Adafruit Accessories OctoWS2811 Adapter for Teensy 3.1-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1779 // Stock Type: NeoPixels >> Drivers // In Stock & Ready to Ship // This adapter board connects the Teensy 3.1 to up to thousands of WS2811/WS2812 (a.k.a NeoPixel) and compatible LEDs using the OctoWS2811 Library . It features a 74HCT245 buffer chip and 100 ohm series matching resistors. A CAT6 Ethernet cable is used to connect this board to the LED strips. A CAT6 cable is designed for very high bandwidth, minimal cross-talk between twisted pairs, and 100 ohm impedance, for a very high quality signal. Teensy 3.1 is a small, breadboard-friendly development board designed by Paul Stoffregen and PJRC. Teensy 3.1 brings a low-cost 32 bit ARM Cortex-M4 platform to hobbyists, students and engineers, using an adapted version of the Arduino IDE (Teensyduino) or programming directly in C language....
  • Adafruit TPIC6B595 High Power Shift Register - TPIC6B595 [AD
    Precio:  $2,049.00

    Adafruit TPIC6B595 High Power Shift Register - TPIC6B595 [AD

    -Titulo Original : Adafruit TPIC6B595 High Power Shift Register - TPIC6B595 [ADA457]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 457 // Stock Type: Components & Parts >> IC & Transistors // In Stock & Ready to Ship // Add a bunch of high-power outputs to a microcontroller system with chainable shift registers. These chips take a serial input (SPI) of 1 byte (8 bits) and then output those digital bits onto 8 pins. You can chain them together so putting three in a row with the serial output of one plugged into the serial input of another to make 3 x 8 = 24 digital outputs. You can chain pretty much as many as you want. This makes it easy to control a lot of outputs like LEDs from only 3 digital microcontroller pins. This item contains ! These chips similarly to the more well known 7HC595s but they are high power drains, able to sink 150mA per pin. They cannot source current so they should be connected to LED cathodes. This makes them ideal for use with LED matrices where you end up sinking 8 or more LEDs at once. These chips are DIP package so you can easily plug them into any breadboard or perfboard with 0.1 spacing. They are not the same pinout as '595s so check the datasheet! For an excellent tutorial on using shift registers, check out the Arduino ShiftOut pag...
  • Adafruit Feather M4 Express - Featuring ATSAMD51 - ATSAMD51
    Precio:  $8,679.00

    Adafruit Feather M4 Express - Featuring ATSAMD51 - ATSAMD51

    -Titulo Original : Adafruit Feather M4 Express - Featuring ATSAMD51 - ATSAMD51 Cortex M4-Fabricante : ADAFRUIT-Descripcion Original: 512KB Flash and 192KB RAM // ATSAMD51J19 // 120MHz Cortex M4 // It's what you've been waiting for, the Feather M4 Express featuring ATSAMD51. This Feather is fast like a swift, smart like an owl, strong like a ox-bird (it's half ox, half bird, OK?) This feather is powered by our new favorite chip, the ATSAMD51J19 - with its 120MHz Cortex M4 with floating point support and 512KB Flash and 192KB RAM. Your code will zig and zag and zoom, and with a bunch of extra peripherals for support, this will for sure be your favorite new chipset. And best of all, it's a Feather - so you know it will work with all our FeatherWings! What a great way to quickly get up and running. The most exciting part of the Feather M4 is that while you can use it with the Arduino IDE - and it's bonkers fast when you do, we are shipping it with CircuitPython on board. When you plug it in, it will show up as a very small disk drive with main.py on it. Edit main.py with your favorite text editor to build your project using Python, the most popular programming language. No installs, IDE or compiler needed, so you can use it on any computer, even ChromeBooks or computers you can't install software on. When you're done, unplug the Feather and your code will go with you. The Feather M4 Express uses the extra space left over to add a Mini NeoPixel, 2 MB SPI Flash storage and a little prototyping space. You can use the SPI Flash storage like a very tiny hard drive. When used in CircuitPython, the 2 MB flash acts as storage for all your scripts, libraries and files. When used in Arduino, you can read/write files to it, like a little datalogger or SD card, and then with our helper program, access the files over USB...
  • Adafruit Stereo Enclosed Speaker Set - 3w 4 Ohm
    Precio:  $3,229.00

    Adafruit Stereo Enclosed Speaker Set - 3w 4 Ohm

    -Titulo Original : Adafruit Stereo Enclosed Speaker Set - 3W 4 Ohm-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1669 // Stock Type: Components & Parts >> Speakers // In Stock & Ready to Ship // Listen up! This set of two 2.8 x 1.2 speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We particularly like these speakers as they are small and enclosed for good audio volume and quality. The pair have a handy SPK input cable to add audio to your displays (the connectors are similar to the JST-PH series  which is ~2.0mm spacing). We're specifically carrying these to use with our 10.1 inch , 7 inch , or 5.6 inch 1280x800 Display w/ Audio driver boards. However, they work peachy-keen with any of our audio amps as well, such as the MAX98306 , TS2012 or TPA2016 stereo class D amplifiers...
  • Flexible Flat Cable, 24 Pins 0.5mm Pitch 150mm Fpc Ffc Flex
    Precio:  $2,959.00

    Flexible Flat Cable, 24 Pins 0.5mm Pitch 150mm Fpc Ffc Flex

    -Titulo Original : Uxcell Flexible Flat Cable, 24 Pins 0.5mm Pitch 150mm FPC FFC Flexible Ribbon Cable For LCD TV Car Audio DVD Player Laptop 20Pcs (A Type)-Fabricante : Uxcell-Descripcion Original: Cubierta completa: protege el cuerpo y los bordes de raspaduras y rayones, y protege la pantalla completa. Parachoques cortado con precisión: la carcasa delgada no agrega volumen a su reloj, imperceptible cuando está encendida. 3 colores diferentes en 1 paquete. Encaja perfectamente con Samsung Galaxy Watch Active 2. Estuche activo flexible: el estuche de TPU suave hace que sea muy fácil de encender / apagar y no rayará el reloj durante la instalación. Ni siquiera se puede decir que hay una caja en el reloj, ya que no agrega volumen. Buen diseño: la funda con recortes se ajusta a todos los botones y orificios de su reloj Galaxy activo, hace que sea fácil de usar todos los puertos y botones, fácil de instalar y quitar. No dude en ponerse en contacto con nosotros si tiene algún problema. NOTA: Utilice un paño seco para limpiar si entra agua, sudor o humedad debajo de la carcasa, ya que esto puede afectar la respuesta táctil...
  • Adafruit 16 MHz Crystal + 20pF capacitors [ADA2215]
    Precio:  $1,929.00

    Adafruit 16 MHz Crystal + 20pF capacitors [ADA2215]

    -Titulo Original : Adafruit 16 MHz Crystal + 20pF capacitors [ADA2215]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2215 // Stock Type: Components & Parts >> Oscillators/Crystals // In Stock & Ready to Ship // Keep your microcontroller tickin' with a a fancy timing crystal. This 16.000 MHz model comes in a HC49/US 'short style' standard package and is breadboard friendly and easy to use with any microcontroller or device that requires an external crystal. We even include two 20pF capacitors!The crystal has 30PPM tolerance, 50PPM stability so it's good even for high precision needs (USB timing, long-term time-keeping, RF/PLL/VCO driving).To use, connect the two pins to XTAL-in and XTAL-out on your circuit (the package is symmetric so use whichever pin) and one capacitor each from a crystal pin to ground. Check your microcontroller datasheet in case you also need a 1 Megaohm resistor or any other components...
  • Adafruit Round Force-Sensitive Resistor (FSR) - Interlink 40
    Precio:  $2,489.00

    Adafruit Round Force-Sensitive Resistor (FSR) - Interlink 40

    -Titulo Original : Adafruit Round Force-Sensitive Resistor (FSR) - Interlink 402 [ADA166]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 166 // Stock Type: Sensors >> Touch // In Stock & Ready to Ship // FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This sensor is a Interlink model 402 FSR with 1/2 diameter sensing region.FSR's are basically a resistor that changes its resistive value (in ohms Ω) depending on how much its pressed. These sensors are fairly low cost, and easy to use but they're rarely accurate. They also vary some from sensor to sensor perhaps 10%. So basically when you use FSR's you should only expect to get ranges of response. While FSRs can detect weight, they're a bad choice for detecting exactly how many pounds of weight are on them.FSRs are made of plastic and the connection tab is crimped on delicate material. The best way to connect to these is to simply plug them into a breadboard or use a clamp-style connector like alligator clips, female header, or a terminal block. It is possible to solder onto the tabs but you must be very fast because if your iron is not good quality or you dally even a few seconds, you will melt the plastic and ruin the FSR! For a full tutorial with wiring diagrams, code examples and project ideas, please read the FSR tutorial page ...
  • Adafruit Audio Ic Development Tools Mono 2.5w Class D Audio
    Precio:  $1,739.00

    Adafruit Audio Ic Development Tools Mono 2.5w Class D Audio

    -Titulo Original : Audio IC Development Tools Adafruit Mono 2.5W Class D Audio Amplifier - PAM8302 (1 piece)-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2130 // Stock Type: Breakout Boards >> Amplifiers/Sound // In Stock & Ready to Ship // This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.0V-5.5VDC. Since the amp is a class D, its very efficient (over 90% efficient when driving an 8Î speaker at over half a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. There's even a volume trim pot so you can adjust the volume on the board down from the default 24dB gain. This board is a welcome upgrade to basic LM386 amps! The A+ and A- inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the Audio- pin  to ground. The output is Bridge Tied - that means the output pins connect directly to the speaker pins, no connection to ground. The output is a high frequency 250KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly. Comes with a fully assembled and tested breakout board. We also include header to plug it into a breadboard and a 3.5mm screw-terminal blocks so you can easily attach/detach your speaker. You will be ready to rock in 15 minutes! Output Power: 2.5W at 4Î, 10% THD, 1.5W at 8Î, 10% THD, with 5.5V Supply50dB PSRR at 1KHzFilterless design, with ferrite bead + capacitors on output.Fixed 24dB gain, onboard trim potentiometer for adjusting input volume.Thermal and short-circuit/over-current protectionLow current draw: 4mA quiescent and 1uA in shutdown mod...
  • Adafruit 10uF 50V Electrolytic Capacitors - Pack of 10 [ADA2
    Precio:  $1,469.00

    Adafruit 10uF 50V Electrolytic Capacitors - Pack of 10 [ADA2

    -Titulo Original : Adafruit 10uF 50V Electrolytic Capacitors - Pack of 10 [ADA2195]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2195 // Stock Type: Components & Parts >> Passives // In Stock & Ready to Ship // We like capacitors so much we made a  kids show about them.    They're super handy and it's really helpful to have a variety lying around to pick and choose from.This is a 10 pack of  10uF 50v  capacitors, so they can be used with any DC voltage up to 50V.  They have a tolerance of ±20% and long flexible pins that make them great for perf or breadboards. Remember that electrolytic capacitors are good for low frequency filtering (~1KHz or less), for higher frequency, pair up with a ceramic capacitor We use these capacitors in our own kits and they're great quality.  They're so useful we're selling them in packs of 10.  Each has nice clear labelling on the body as well in case you have a capacitor mix up...
  • Adafruit BMP280 I2C or SPI Barometric Pressure & Altitude Se
    Precio:  $3,429.00

    Adafruit BMP280 I2C or SPI Barometric Pressure & Altitude Se

    -Titulo Original : Adafruit BMP280 I2C or SPI Barometric Pressure & Altitude Sensor-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2651 // Stock Type: Sensors >> Barometric Pressure // In Stock & Ready to Ship // Bosch has stepped up their game with their new BMP280 sensor, an environmental sensor with temperature, barometric pressure that is the next generation upgrade to the BMP085/BMP180/BMP183. This sensor is great for all sorts of weather sensing and can even be used in both I2C and SPI!This precision sensor from Bosch is the best low-cost, precision sensing solution for measuring barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are so good, you can also use it as an altimeter with  ±1 meter accuracy.The BMP280 is the next-generation of sensors from Bosch, and is the upgrade to the BMP085/BMP180/BMP183 - with a low altitude noise of 0.25m and the same fast conversion time. It has the same specifications, but can use either I2C orSPI. For simple easy wiring, go with I2C. If you want to connect a bunch of sensors without worrying about I2C address collisions, go with SPI.Nice sensor right? So we made it easy for you to get right into your next project. The surface-mount sensor is soldered onto a PCB and comes with a 3.3V regulator and level shifting so you can use it with a 3V or 5V logic microcontroller without worry. We even wrote up a nice tutorial with wiring diagrams, schematics, libraries and examples to get you running in 10 minutes! And make sure to check the tutorial for pinouts, assembly, wiring, downloads, and more...
  • Adafruit FONA - Mini Cellular GSM Breakout - SMA Version [AD
    Precio:  $9,679.00

    Adafruit FONA - Mini Cellular GSM Breakout - SMA Version [AD

    -Titulo Original : Adafruit FONA - Mini Cellular GSM Breakout - SMA Version [ADA1963]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 1963 // Stock Type: Wireless >> Cellular // In Stock & Ready to Ship // Ring, Ring! Who's that callin'? It's your breadboard! Introducing Adafruit FONA MiniGSM, an adorable all-in-one cellular phone module that lets you add voice, text, SMS and data to your project in an adorable little package. This module measures only 1.75x1.25 but packs a surprising amount of technology into its little frame. At the heart is a GSM cellular module (we use the latest SIM800) the size of a postage stamp. This module can do just about everything. This version has an SMA connector. For the uFL version, click here! Quad-band 850/900/1800/1900MHz - connect onto any global GSM network with any 2G SIM (in the USA, T-Mobile is suggested)Make and receive voice calls using a headset OR an external 8Ω speaker + electret microphoneSend and receive SMS messagesSend and receive GPRS data (TCP/IP, HTTP, etc.)Scan and receive FM radio broadcasts (yeah, we don't exactly know why this was included but it works really well)PWM/Buzzer vibrational motor controlAT command interface with auto baud detectionSounds delicious, right? So we plated this fine module onto a little breakout with all the extras you need to make your next project shineOnboard LiPoly battery charging circuitry so you can take your project on the go. Use any 500mAh+ LiPoly or LiIon battery and recharge over the MicroUSB when necessary. Two LEDs let you know when its charging and doneStandard 4-pole TRRS headphone jack. Use any 'Android' or 'iPhone'-compatible headset with micBreakouts for external 8Ω speaker and electret mic if you don't want to use a headphoneLevel shifting circuitry so you can run it with 2.8V to 5V logic.Vibrational motor (buzzer) driver so you can have noiseless notificationsSMA connection for external antennaIndicator LEDs for power and network connectivity Standard SIM slides into the bac...
  • Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]
    Precio:  $4,619.00

    Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]

    -Titulo Original : Adafruit USB/DC/Solar Lithium Ion/Polymer Charger [ADA390]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 390 // Stock Type: Power >> Solar >> Chargers // In Stock & Ready to Ship // NOTE: This product is only designed for use with solar panels sold at the Adafruit store. We cannot guarantee this will work with solar panels purchased elsewhere. Please purchase this kit and panels from Adafruit to ensure optimized functionality! A 2.1mm adapter cable is also required to adapt a solar panel to the DC power jack. Make your projects to go green this summer with our specialized USB/Solar Lithium Ion Polymer Battery charger! This charger is a very unique design, perfect for outdoor projects, or DIY iPod chargers. We've spent over a year testing and tinkering with this charger to come up with a plug and play solution to charging batteries with the sun and we're really pleased with what we ended up with. Easy to use! Pick up any of our many 3.7V/4.2V LiIon batteries , and a 6V solar panel . Plug the battery into the BATT port using a 2-pin JST cable and the solar panel into the DC jack using a 2.1mm adapter cable Put the solar panel outside (and keep the battery out of the sun, it needs to be kept cool!) to start charging. You can power another project like a Mintyboost at the same time by connecting to the LOAD output port Our carefully designed charger is designed specifically for solar charging, and will automatically draw the most current possible from the panel in any light condition! Even thought it isn't a 'true' MPPT (max power point tracker), it has near-identical performance without the additional cost of a buck-converter. Our detailed tutorial on how to use this charger includes a design document explaining how it all works. For use with Adafruit Lipoly/LiIon batteries only! Other batteries may have different voltage, chemistry, polarity or pinout. Comes with an assembled charger board, a 2-pin JST cable that will fit into either the BATT or LOAD ports, and a large stabilization capacitor that must be installed in your finished project. Doe...
  • Adafruit IC Socket - for 8-pin 0.3 Chips - Pack of 3 [ADA220
    Precio:  $2,549.00

    Adafruit IC Socket - for 8-pin 0.3 Chips - Pack of 3 [ADA220

    -Titulo Original : Adafruit IC Socket - for 8-pin 0.3 Chips - Pack of 3 [ADA2202]-Fabricante : ADAFRUIT-Descripcion Original: Adafruit Part Number: 2202 // Stock Type: Components & Parts >> Sockets/Connectors // In Stock & Ready to Ship // An IC (Integrated Circuit) socket allows you to insert and remove chips easily from an assembled kit or project This item contains 3 of the 8 pin 0.3 wide version. Best used with chips that have 8 pins (2x4) and have 0.3 pin spacing. These are often used for soldering into a Perma Proto or PCB so that you can replace and swap chips easily. What's nice about IC sockets is that they are the same pin spacing and size so you don't have to redesign the board! For our example photo, we put the socket into an  Adafruit Perma-Proto Breadboard but any solderable PCB or protoboard will work great. Not recommended for solderless breadboards, the pins are not long enough...
Mostrar del 1 al 24 (de 169 productos)
Páginas de Resultados:  1  2  3  4  5 ...  [Siguiente >>]